SSR ULTRA-PLUS COOLANT TECHNICAL DATA Typical Properties of Ultra Plus Synthetic Compressor Lubricant Property
Test Method
SAE Viscosity Classification J300 ISO Viscosity Classification ASTM D2422 Viscosity Index D2270 Viscosity, cSt (SUS) at 40°C D445 at 100°C D445 at 0°F D445 at -40°C D445 Pour Point, °F (°C) D97 Flash Point, °F (°C) D92 Auto Ignition Temperature, °F (°C) E659 Conradson Carbon Residue, % D189 Copper Strip Corrosion, 3 hrs @ 212°F/100°C D130 4-Ball Wear, 40kg, 1 hr, 1800 rpm, (mm) D2266 Weld Point, kg D2783 Evaporation Loss 6.5 hrs @ 400°F D972 Specific Gravity @15.6°C D1298 Ferrous Metal Corrosion (Rust Test) Distilled Water D665A Synthetic Sea Water D665B Foam Tendency (Sequence I, II, III) Sequence I D892 Sequence II D892 Sequence III D892 Total Acid Number D664 High Pressure Oxidation Test (hr) D2272 Specific Heat, cal/gm/°C at 185°F (btu/lb mol °F) D2766 Thermal Conductivity, cal/(cm)(sec)(°C) at 150°F D2717 at 200°F D2717 at 250°F D2717 Demulsibility @ 130°F (54°C) ml oil/emulsion (min) D1401
Performance SAE10/20 32 150 34.9 6.65 1100 13,800 -59 (-51) 263 (128) 424 (218) <0.1 1a 0.73 100 4.13 0.9752 pass pass Nil 11.5 ml Nil 0.19 18.5 0.47 36.4x10 -5 34.6x10-5 33.7x10-5 41-39-0 (35)
Technical Data TOXICITY: Please refer to the Material Safety Data Sheet for Ultra Plus (Form APDD-772). COMPATIBILITY: The following lists serve as a guide for the material compatibility of various seals, plastics, and paints with Ultra Plus*. ACCEPTABLE: Seals: Fluorocarbon (Viton®), High Nitrile Buna-N, Florosilicone Rubber, Polysulfide, Hytrel®, Kalrez®, CPM Plastics: Nylon, Teflon®, Deltrin®, Celcon®, PBT, HD-PPE, Ryton® (oil-less) Paints: Epoxy, Baked Phenolic, 2-Comp Urethane, MC-Urethane, Oil-Resistant Alkyd
NOT RECOMMENDED: Seals: Neoprene, Natural Rubber, SBR, Buna-S, Butyl Rubber, Chlorosulfonated polyethylene, Low Nitrile Buna-N Plastics: Polystyrene, PVC, ABS Paints: Acrylic, Latex (household), Vinyl, Varnish, Lacquer *Under normal circumstances. In extreme conditions, such as high temperatures (over 250°F) and/or high stress, compatibility should be re-evaluated. Note: In the case of employment of new seal composition, lubricant compatibility should be evaluated. Please refer to Ingersoll-Rand Contract Service, Davidson, North Carolina.
APPLICATION DEPENDENT: Seals: Med Nitrile Buna-N, Polyurethane, EPDM, Epichlorohydrin, Polyacrylate Rubber, Silicone Rubber Plastics: Polyurethane, Polyethylene, Noryl®, Lexan®, Lucite®, Polysulfone, Polycarbonate (type) Paints: Alkyds, Phenolic, SC-Urethane, Industrial Latex
MORE THAN AIR. SOLUTIONS. Online solutions: www.air.ingersoll-rand.com Ingersoll-Rand compressors are not designed, intended or approved for breathing air applications. Ingersoll-Rand does not approve specialized equipment for breathing air applications and assumes no responsibility or liability for compressors used for breathing air service. Nothing contained on these pages is intended to extend any warranty or representation, expressed or implied, regarding the product described herein. Any such warranties or other terms and conditions of sale of products shall be in accordance with Ingersoll-Rand’s standard terms and conditions of sale for such products, which are available upon request. Ingersoll-Rand Company Air Solutions Group 800-C Beaty Street Davidson, NC 28036
©2001 Ingersoll-Rand Company
Form SCD-964 Printed in USA
05515184
