Your bucket tooth - Plasterer

Your bucket tooth information source including product features, applications and specifications for the following product lines: Ø Ø Ø Ø Ø Ø Ø Ø Ø

Fanggs Deere Caterpillar replacement Hensley replacement Esco Conical replacement Esco SuperÔ Esco Helilokâ/Vertalokâ H & L replacement

Rippers and scarifiers

Bucket Tooth Basics Tooth Performance and Wear Life

Tooth Performance and Wear Life

Maximum performance and wear life are the two most important characteristics for replacement teeth. Working with constant abrasive material places extreme demands on both design and strength.

Design

=

Performance

Strength

=

Wear Life

The best designed tooth is always a compromise of performance and wear life.

Design is directly related to performance while strength is directly related to wear life. Tooth Penetration Penetration is a key design consideration for all replacement teeth.

To Achieve Good Tooth Penetration

To achieve good penetration, a tooth must have a sharp point for initial ground entry. The tooth blade must taper gradually enough to reduce resistance to penetration and yet be thick enough to avoid breakage.

1. Tooth must have sharp point. 2. Blade must taper gradually to reduce resistance. 3. Blade must be thick enough to avoid breakage.

The easier it is to penetrate the material…the less horsepower is required for operation. Tooth Centerline vs. Non-Centerline Design All centerline points are reversible to distribute wear and stay sharp. Non-centerline points can be rotated to balance wear patterns, but they cannot be “flipped over” to resharpen.

PI7262 Litho in U.S.A. (97-02)

Basics 1

Bucket Tooth Basics (Continued) Tooth Breakage Tooth wear is expected, but tooth breakage under normal working conditions is not!

Tooth Installation The job of a tooth retainer is to withstand impacts or shocks transmitted through the tooth without breaking or falling out. It must also take up manufacturing tolerances so the tooth stays tight on the adapter.

Tooth breakage in extreme conditions - very hard abrasive material where blasting, ripping, or air hammering might be more effective should be expected.

The various types of “hardware” to install teeth are covered in detail within each section. These are some types of hardware or retainers used:

The worst thing an operator can do is use the bucket with missing teeth. A missing tooth exposes the adapter nose piece to wear. Any amount of worn metal from the adapter nosepiece leaves an open pocket between the adapter and the replaced tooth. This open area allows the tooth to work back and forth. The adapter can no longer provide the support necessary to firmly attach the tooth to the bucket. To find out if the nosepiece is the reason for the tooth breakage, remove the tooth tip. If the nosepiece is worn, the original shank or adapter should be replaced.

Flex Pin Spring Pin Horizontal Pin and Split Washer Roll Pin Groove Pin Crimp-On Pin and Lock Quadrilok® Pin and Plug Tooth Wear It is a good idea to inspect bucket teeth, adapters, and the bucket condition daily. By determining wear patterns and rotating teeth, you can extend wear life and increase productivity which, in turn, provides you the greatest return for the money invested. When using the right tooth and operating the bucket according to standard practice, a pattern will develop for normal wear. The tooth will maintain a profile similar to the original profile and it will continue to penetrate material quickly and easily. But even when using the right tooth, tooth wear is seldom even. Teeth that are near bucket corners generally wear fastest. And a bucket that is regularly loaded at an angle will show uneven wear on the loading side. Rotating teeth will help equalize the wear.

Both abnormal wear and breakage can be prevented with the right choice of teeth. Some suggestions include reducing the size and length of the point or switching to a forged or cast tooth when material becomes harder and more abrasive.

While teeth could assume the shape of a fist due to improper use of the bucket such as scraping, dragging, or banging, it is most likely that the wrong teeth are being used for the application. Using the wrong teeth for the application takes more power to penetrate material and reduces productivity.


Basics 2

Bucket Tooth Basics (Continued) Tooth Position FANGGS teeth have a curved shape to extend the contour of the bucket which results in a continuous flow of material to achieve maximum bucket fill. Reversing Fanggs teeth so that the curve of the tooth is opposite that of the bucket is not recommended.

Forged and cast backhoe and excavator teeth can be reversed as shown in this drawing. The flat of the tooth faces away from the open side of the bucket. As you can see, tooth angle is less aggressive. Teeth can be mounted in this position to avoid disturbing the trench floor.

Teeth other than Fanggs installed on backhoe and excavator buckets are mounted as indicated in the above illustration. The flat area of the tooth faces the open part of the bucket. In this position, tooth entry into the ground is very aggressive. It allows the teeth to break material for easier bucket loading. It is recommended that teeth be mounted in this position for normal digging conditions.


It is not recommended that fabricated teeth be mounted in this reversed position. As the bucket is being loaded, material will wear thin the clip portion of the tooth. Eventually, tooth breakage will occur. The clip is made of a softer metal and as a result is more susceptible to wear than the blade portion of the fabricated tooth.

Basics 3

Adapter Installation Various retention methods between the adapter and bucket as well as the tooth and adapter are available. Check the condition of the bucket and repair as necessary before installing an adapter. 3. On hydrostatic crawler loaders, preheat the cutting edge holes (second set from each end) to 400˚F (204˚C).

Bolt-On Adapters When installing a new adapter, be sure the cutting edge provides a firm mounting base. If the edge has been worn and doesn’t provide support, the adapters are susceptible to breakage. Always use the attaching hardware recommended for the application. Bolt tensile strength has been matched to specific application requirements. Weld-On Adapters

4. Use a temperature stick (Tempilstik or equivalent) to check preheat temperature.

Warning: Persons performing welding and other maintenance work should wear OSHAapproved safety equipment such as hard hats, safety shoes and glasses, work gloves, and the proper lenses in welding gear. When welding adapters to the bucket cutting edge, make sure the cutting edge provides a firm mounting base. This support is necessary as adapters are also susceptible to breakage. Welding to the bucket cutting edge may cause cracks in the cutting edge if a firm mounting base is not provided and good welding techniques are not followed:

5. Fill the holes with plug welds.

1. Remove the tooth and pin from the adapter prior to welding. High welding temperatures can have a detrimental effect on tooth heat treatment. 2. Clean the area to be welded. Remove paint by sanding or grinding. Remove oil and grease using a safe solvent. Remove rust and dirt using a wire brush.


6. Grind weld flush with top cutting edge surface.

Basics 4

Adapter Installation (Continued) 9. Use a smaller diameter (0.12″ (3 mm) maximum) electrode to make the Jgroove welds with an unequal leg fillet weld (2). Extend the longer leg onto the cutting edge.

7. Tack weld the rear of the adapter to the cutting edge. 8. Preheat adapter to 400-600˚F (204306˚C) before welding. Use a temperature stick to check for correct temperature.

10. Start at the rear of the adapter. Weld one pass to 1″ (25.4 mm) from the edge (4). Weld one pass on the other side of the adapter. 11. Chip off the slag and peen each weld bead after each pass. Alternate from one side of the adapter to the other side for each pass. 12. After all adapters are welded, uniformly heat the edge and all adapters to 400˚F (204˚C). Let the adapters and cutting edge cool slowly in still air.


Basics 5

Manufacturing Process ADI Teeth Austempered ductile iron teeth are used on backhoes, excavators and loaders. They offer moderate to heavy impact resistance. An ADI tooth is essentially a cast tooth of different chemistry, ductile iron which is brought to heat in a controlled environment (austempering). John Deere has a video offering further explanation of ADI (DGVHI93821 available from DSC). The pattern is then mounted on an automatic molding machine. This machine takes preconditioned sand that has been mixed with clay and water and compresses the sand against both sides of the pattern plate to form the two halves of the mold. These two halves of the mold are pulled away from the pattern leaving detailed impressions in the sand. Then the shell cores are strategically placed into the imprint. Now the two halves are joined forming the casting impression. The molds are next transferred by conveyor to the mold handling system. A metal jacket is placed around each mold to insure that no side movement occurs between the mold halves. The weight is set on top of the mold to apply additional pressure so that no separation occurs as the pouring process is completed.

The manufacturing of ADI teeth starts naturally with an engineering drawing of the part itself. From the drawing, critical dimensions are utilized to machine a metal pattern. The pattern is then used to manufacture prototype castings. These are evaluated by engineering to confirm the design. If any pattern adjustments are required, additional tooth samples are produced and final approval authorized.

The combination of the following metals provide high strength and ductility: • Pig iron • Manganese • Steel • Along with other alloys including carbon and silicon

The pattern forms the outside shape of the tooth. It incorporates the gating system which is the path the molten metal flows through to the actual tooth cavities.

All of these materials have the necessary metallurgical chemistry to meet John Deere’s strict specifications.

Although the pattern forms the outside shape of the tooth, the pocket area is formed by a core. The core is produced in a metal machined core box. The box is injected under pressure with a resin-coated sand.

This raw material is carefully weighed so that there is a consistent cross match of ongoing, solid, raw material with an outgoing molten ductile iron.

By using heat, the resin-coated sand grains bond together forming a shell core. The shell core is dipped into a liquid metal protectant which provides a smooth pocket and accurate pin hole location.


The charge vessel is moved in place over the electrical furnace and material is released. After approximately 15 minutes, the material will be heated to about 2700 degrees Fahrenheit and will be transformed into a liquid state. Basics 6

Manufacturing Process (Continued) ADI Teeth (Continued)

Cast Teeth

The metal undergoes chemistry analysis to monitor quality standards.

Cast teeth are used on loaders, scrapers, rippers, and scarifiers. They are formed from a medium-carbon, chromium, nickel, molybdenum steel offering high strength and toughness with deep-hardening properties. They have excellent resistance to wear and abrasion.

The iron is then poured into an inoculation ladle, magnesium is added, and it is then transferred to the pouring area.

The manufacturing process begins with the pattern which is basically an exact duplicate of the tooth to be cast but slightly oversized to compensate for steel contraction. The mold is made from this pattern. The mold consists of silica sand and binder. It contains the cavity into which the molten metal will be poured in order to form the casting. The mold is made in two sections with the top half referred to as the cope and the bottom as the drag.

The iron pourer will check the molten iron for proper pouring temperature and magnesium inoculations. If the material passes inspection, molds are poured. The metal travels through the gating and fills each tooth cavity.

The core is also made of a sand mixture. When placed in the mold, it forms the tooth pocket area. At this point, liquid cement is applied to the cope and drag. Clamping fixtures press the two pieces together.

Once poured, the carousel moves the mold to the cooling chamber for a specified time. Afterwards the teeth are removed mechanically and pass down the shake-out area. This removes the majority of sand from the casting.

Metal is placed into the furnace for the melt process. The melt process begins as three, 8inch (203 mm) diameter graphite electrodes moving in tanden work their way downward through the charge. An electric arc is maintained between the electrodes and the charge. When the electrodes reach the bottom, the initial transformation to liquid steel takes place. The entire charge is then transformed into liquid steel as the electrodes slowly return upward. At this point, the temperature of the steel is approximately 2900˚F (1593˚C).

The castings are now transported to the tumble-blast area for final cleaning. They are shuttled to a grind step to remove the end gates and any protrusions. Quality assurance and analysis occurs throughout the processes. Constant monitoring of the sand and metal micro structure ensure a high quality casting.

Following the adjustments dictated by steel and slag samples taken to determine carbon level and stage of melt process, the melt is refined. Temperature is raised to 3200˚F (1760˚C), and tested again to determine if alloy adjustments are necessary. The entire melt is then poured into a tapping ladle, reladled into small pouring ladles, and poured into the mold.

Spectrographic analysis is also constantly performed to provide proper metal chemistries. Inspection steps continue as Brinell Hardness and additional quality audits are consistently administered. In final process, the castings undergo an austempering heat treatment. This makes the final product stronger, harder, tougher. PI7262 Litho in U.S.A. (97-02)

Basics 7

Manufacturing Process (Continued) Forged Teeth

Cast Teeth (Continued)

Forged teeth are used on backhoes, loaders, excavators and motor graders. Chrome-moly alloy steel along with the continuous fibre structure and grain flow of the steel provide increased strength while maintaining hardness. Forged teeth have a high tensile strength while maintaining excellent ductility.

After cooling, the teeth are run through a shakeout to remove the mold and cores. Castings go through an additional cleaning operation to remove all sand. Using acetylene torches, excess material is removed from the teeth which then go through a finishing grind to remove all excess metal. Forged teeth are produced from steel bars and billets with specified and carefully controlled analysis. The raw material is cut to size and heated in electric induction heating units to forging temperatures. Electrical heating provides a much higher quality product than gas heating. Following heating, the part undergoes up to ten steps in the forging process to form the tooth from the solid steel billet. After forging, the individual parts are inspected, hand finished, and then sent on to heat-treating.

All John Deere cast teeth are differentially heat-treated to provide the hardness, wear resistance, and toughness for the longest, most productive life.


In the heat-treating process, the teeth are individually placed in containers to provide thorough and even heating. Next, they are loaded into endothermically-controlled atmosphere furnaces where they are heated to a closely controlled temperature. This type of furnace allows the surface chemical analysis of the part to be maintained and ensures that the part will be heat-treated to the maximum attainable hardness. Following the hardening process, the teeth are tempered and inspected for hardness.

Basics 8

Manufacturing Process (Continued) Two pieces - the blade and the clip - comprise the fabricated tooth. Since the blade incurs most of the wear, it is made of chrome-nickelmoly alloy steel heat-treated to Rockwell C4550. The clip is shaped to form the exact pocket size required for precise adapter fit. It is electronically welded to the blade and then heat-treated and tempered.

Fabricated Teeth Fabricated teeth are used on backhoes, excavators, and motor grader rippers. They are standard-duty teeth which are self-sharpening and feature easy replacement and economy.

Nodular Iron Teeth Nodular iron teeth are available on utility crawler loaders. These teeth are a one-piece, bolt-on type. They are generally used in lightduty applications.


Basics 9

Hardness Testing Two tests are commonly used for hardness testing.

Charpy Test (Impact Stronger)

Brinell Hardness

A test bar (a small metal bar from a pour approximately 6” long) is notched and placed on the anvil. The hammer portion of the testing machine is released with adequate force to break the sample. The scale measures the energy absorbed by the sample during the fracture. The farther the pendulum swings through the sample, the more brittle the material.

The Brinell Hardness Number (BHN) is one of the oldest tests and is the most common standard. The tooth is placed on the anvil and a steel ball is pressed into the sample with a load of 3000kg. The load is then left in place for 30 seconds and then removed. The diameter of the impression is then read in millimeters with a low power microscope with a measuring eyepiece and the BHN is determined.

John Deere’s charpy range is from 17-19 which indicates excellent impact strength.

The BHN in John Deere’s product line is 475-500.


Basics 10

Warranty

or labor for tooth removal and installation; all other remedies are expressly excluded.

Guaranteed against breakage! Warranty applies to a John Deere ADI, cast or forged replacement tooth that breaks during operation before it wears out provided: (1) the tooth has not been hard faced or repaired, (2) it is used on a matching tooth adapter, and (3) the tooth support surface of the adapter has been properly maintained. A new tooth of the same type will be furnished free of charge by any authorized John Deere industrial dealer.

In addition, John Deere’s normal parts warranty and its terms and conditions (see John Deere Service Parts Warranty for details) applies to any ADI, cast or forged tooth under the above warranty which may otherwise prove defective in material or workmanship within 90 days after purchase.

John Deere’s obligation under this warranty does not cover hardware for attaching the tooth


Basics 11

Tooth Pocket Dimensions (Refer to Replacement Section for Specific Part Numbers)

At times, part number information is not always readable on a worn tooth. There are several ways to identify a design and then a specific part number: 1. Tooth Pocket Dimensions Measure the tooth pocket width and height and reference the dimensions in the list below to isolate the tooth type (Caterpillar, H & L, Hensley, etc.) and series. Then look in the corresponding replacement section which includes photos, line drawings, and dimensions to establish the tooth needed for the application. 2. Retention Hardware Use the actual size illustrations of the retention hardware included at the end of each replacement section to determine possible tooth type (Caterpillar, H & L, Hensley, etc.) and size. Tooth Pocket Width 1-13/32″ 1-1/2″ 1-9/16″ 1-9/16″ 1-5/8″ 1-5/8″ 1-3/4″ 1-13/16″ 1-15/16″ 2-1/16″ 2-1/4″ 2-3/8″ 2-1/2″ 2-11/16″ 2-7/8″ 2-7/8″ 3″ 3″ 3-5/32″ 3-13/32″ 3-1/2″ 3-1/2″ 3-17/32″ 4″ 4″ 4-5/16″ 4-1/2″ 4-3/4″ 4-7/8″ 6″ PI7262 Litho in U.S.A. (97-07)

Tooth Pocket Height 1-27/32″ 1-5/8″ 1-11/16″ 2-1/8″ 1-5/8″ 2-3/8″ 2-11/32″ 1-1/2″ 2-11/16″ 2-1/8″ 2-1/8″ 3-1/32″ 2-1/8″ 3-5/16″ 2-1/8″ 2-11/16″ 2-1/8″ 2-1/4″ 3-21/32″ 3-3/16″ 2-5/8″ 2-7/8″ 3-29/32″ 2-7/8″ 3″ 4-11/32″ 3-1/4″ 3-1/2″ 5-1/2″ 5−29/32″

Replacement Section Caterpillar H&L H&L H&L Hensley Hensley Caterpillar Esco Conical Caterpillar H&L Hensley Caterpillar Esco Conical Caterpillar H&L Hensley Hensley Esco Conical Caterpillar Hensley Esco Conical Hensley Caterpillar Hensley Esco Conical Caterpillar Esco Conical Hensley Caterpillar Caterpillar

Tooth Pocket Dimensions 1

Series 20 23 – 24 156 160 22 18 25 25 220 30 25 35 27 290 310 30 40 330 35 350 45 400 40 55 45 475 45 Abrasion (Standard) 70

Fanggs Teeth: A John Deere Exclusive! Better Bucket Fill Better Level Bucket Operation Better Start-Dig Characteristics Exclusive to John Deere

Whether it is breaking-up gumbo, slicing through frost, moving hard-packed sand, or general-purpose digging, Fanggs will answer the call! The patented, guaranteed-againstbreakage, competitively-priced Fanggs teeth provide better bucket fill, better level bucket operation, and better start-dig characteristics due to their design.

Curved Profile Fanggs teeth are curved. That is why they dig with less effort. The curved profile allows them to closely track the path of the bucket. Conventional teeth work against the bucket as they pass through the soil.

Without Fanggs Teeth

With Fanggs Teeth

Better Bucket-Fill and Faster Cycles with Fanggs Teeth You get better bucket-fill and faster cycles with Fanggs teeth because the rolling action causes the soil to collect at the back of the bucket instead of the middle.


Fanggs/John Deere 1

Fanggs Teeth: A John Deere Exclusive! Self-Cleaning Effect Fanggs teeth have a self-cleaning effect that lets dirt flow between the teeth. The moldboardshaped sidewalls decrease friction and soil compaction. Wear Characteristics Wear characteristics are relative to your application and the material you are working in. But there are many instances where the wear differential of Fanggs teeth is more - lots more than conventional teeth.

Soil Bin Test A soil bin test was performed using a Fanggs tooth and a standard tooth. Teeth were assembled to run one at a time completely submerged through identically compacted soil. Tests were run at a constant 1/2 mph.

Soil Bin Test Results Standard Tooth Fanggs Tooth Additional Force Required with Standard Tooth

Force Required 101.5 pounds 78.5 pounds 23.0 pounds

23.0 pounds divided by 101.5 pounds = nearly 22.7% less effort required with the Fanggs tooth!

The standard tooth required 101.5 pounds of force while the Fanggs tooth required only 78.5 pounds of force to transverse the same soil. The Fanggs tooth required nearly 22.7% less effort to do the same work! Vertical Force There was also a significant difference noted in the vertical force between the standard tooth and Fanggs. The standard tooth showed a 4.7 pound force trying to plane up out of the soil. The Fanggs tooth had a 5.0 pound force trying to go deeper. So while requiring nearly 23% less effort to traverse the same soil, the Fanggs tooth was trying to work harder.


Fanggs/John Deere 2

Fanggs Teeth: A John Deere Exclusive! Two Types of Fanggs There are two basic designs of the Fanggs teeth: one is for digging, the other for loading.

Digging Tooth

Loading Tooth

Each tooth is designed to provide optimum performance by filling the bucket faster and requiring less force. Material flow during operation is smooth and consistent on both the top and side surfaces. Operation Comparisons Let’s take a look at comparisons of Fanggs and conventional teeth during various operations.

Conventional Tooth

Fanggs Tooth

Conventional Tooth

Fanggs Tooth

Loading

Digging A conventional tooth uses a wedging action to penetrate material.

A ski-nose pattern appears on conventional loader teeth.

A Fanggs tooth slices through material for more productivity and less effort.

The Fanggs design creates a level bucket wear pattern.

Crowding Conventional teeth rake material away from walls. Fanggs teeth peel material away from walls.


Fanggs/John Deere 3

Fanggs Teeth: A John Deere Exclusive! Part No. Explanation Various information can be determined from the part number system. Refer to the following chart for basic part numbering information. Part Number Explanation for John Deere Fanggs Prefix

Suffix

Explanation

TF

D

Fanggs Digging

TF

L

Fanggs Loading

Operator Tips With conventional teeth, many operators start by raking the earth. It is a fast way to open the land, but it can wear out a set of teeth very quickly. The unique slicing action of Fanggs teeth make raking unnecessary. You can start digging immediately. Here’s how:

3

2

1

1. Start with a steep angle of entry as shown above. 2. Keep the bucket at a flatter attitude as you continue to dig. 3. Maintain this flat profile, then curl the bucket as you complete the dig cycle. This technique allows you to do the job faster and requires less power. It also helps maintain the natural compaction of the soil while reducing the chance of undercutting.


Fanggs/John Deere 4

Fanggs/John Deere Retention and Installation

Horizontal Pin and Split Washer

Spring Pin

Replacement teeth for both John Deere and Caterpillar are retained with a horizontal pin and split washer. This 2-piece retention method makes tooth removal and installation fast and easy. Both the pin and washer are reusable.

The spring pin is an economical means of retaining teeth. The spring in the pin takes up manufacturing tolerances and keeps the tooth tight against the adapter. When removing spring pins from John Deere teeth, use special tool JDG97 (see Special Tools below).

Flex Pin Special Tools When removing spring pins from John Deere teeth, use special tool JDG97. When removing flex pins from backhoe and excavator teeth, use special tool D05339ST. These tools are available from SERVICEGARD.

The flex pin is designed to withstand shock and take up small amounts of adapter wear to provide the necessary tight fit. The pin should be installed so the half groove faces forward towards the tooth tip. The groove is the locking mechanism.

Pin Master® is also available and boasts of 3 minute removal and replacement time for an entire set of 23 Series backhoe teeth. Order TY15994 through your normal parts system.

Flex pins are reusable when properly removed. Use special tool D05339ST when removing flex pins from backhoe and excavator teeth – see “Special Tools.” Do not use bolts in place of flex pins when installing teeth. Bolts create wear on pin holes and promote tooth breakage. If teeth do not stay on, there is probably an adapter problem.


Pin Master® Tooth Replacement Tool (TY15994)

Fanggs/John Deere 5

John Deere TF__D (Digging) TF__L (Loading) Non-Centerline

Fanggs Digging and Loading Teeth • For general-purpose to heavy-duty digging conditions. • Fanggs digging teeth have a curved shape and track the path of the bucket. • Fanggs loading teeth have a flat bottom for improved bucket control.

-A-

-B-

-C-

Width

Point

Series

Tooth Part No.

Length

Cat 20 Series

TF1U3202 (Digging)

5-7/8″

Cat 25 Series

TF1U3252D (Digging)

7-5/8″

Retainer Washer

Retainer Washer

Retainer Washer

TF1U3202P T4T0001

T9J2258 T3G9609

PM8E6258 PM8E6259

Cat 25 Series

TF1U3252L (Loading)

Retainer Washer

Retainer Washer

T9J2258 T3G9609

Cat 30 Series Retainer Washer

T9J2308 T3G9609


-EPocket Height

1-3/4″ 1/8″ 1-13/16″ 1-5/8″ ADI 4.1 lb. Cat: 416, 426, 428, 436; Competitive: Equipment with Cat 20 Series-type adapters.

2-1/2″ 1/8″ 2-11/16″ 2″ Cast 9.0 lb. Cat: 205, 206, 211, 212, 213B, 214B, 613, E110, E120B, E200, EL200; Competitive: Equipment with Cat 25 Series-type adapters.

7-5/8″

2-1/2″ 1/8″ 2-11/16″ 2″ Cast 9.0 lb. JD: 544E, 544G, 624E, 624G, 644H; Cat: 613, 916, 920, 924F, 926, 930, 936, 938F, 939, 941, 941B, 943, 943GLP, 951, 951C, 953, 953GLP, IT12, IT24, IT28; Competitive: Equipment with Cat 25 Series-type adapters.

TF1U3302D (Digging)

9″

3″

1/8″ 3″ 2-1/2″ ADI 12.3 lb. JD: 690E; Cat: 205, 206, 211, 212, 213B, 214B, 215, 219, 224, 235, E180, E200, EL200; Competitive: Equipment with Cat 30 Series-type adapters.

TF1U3302L (Loading)

8-3/4″

3″

T9J2308 T3G9609

Cat 30 Series Retainer Washer

PM8E6258 PM8E6259

-DPocket Width

1/4″ 3″ 2-1/2″ Cast 13.3 lb. JD: 644E, 644G, 644H; Cat: 950, 950B, 955, 966, 966C; Competitive: Equipment with Cat 30 Series-type adapters.

Fanggs/John Deere 12

John Deere

Fanggs Digging and Loading Teeth (Continued)

Series

Tooth Part No.

Cat 35 Series

TF1U3352D (Digging)

Retainer Washer

Retainer Washer

T9J2358 T3G9549

T8E6358 T8E6359

Cat 45 Series

TF9W8452D (Digging)

Retainer Washer

Retainer Washer

T1U1458 T3G9549

PM8E0468 PM8E8469

-A-

-B-

-C-

Length

Width

Point

Pin

3-3/8″ 4-3/4″ 3-1/4″ 2-15/16″ Cast 16.9 lb. JD: 790D, 790E, 892D, 892E; Cat: 205, 206, 211, 212, 213B, 214B, 224, 225, 229, 231, 245, E240, E248; Competitive: Equipment with Cat 35 Series-type adapters. 10″

3-3/8″ 4-3/4″ 3-7/8″ 3-7/8″ Cast 28.5 lb. JD: 790D, 790E, 892D, 892E, 992, 992D; Cat: 224, 225, 229, 235, 325, 330, 375, E240, E248, E300; Competitive: Equipment with Cat 45 Series-type adapters.

Pin

TF23D (Digging)

1-3/4″ 1/8″ 1-1/2″ 1-5/8″ ADI 3.8 lb. JD: Buckets with H & L 23 Series adapters (5/8″ or 3/4″ edge); Case: 480F, 580K, 590, 680L, 780D; Ford: 555D, 575D, 655D, 755B, 710D; Competitive: Backhoes with H & L 23 Series-type adapters (5/8″ or 3/4″ edge).

TF23L (Loading)

5-7/8″

TF252 (Digging)

7-1/2″

TF23P

H & L 25 Series Pin

Loading

TF23P

H & L 23 Series

TF25P


-EPocket Height

10″

Digging

H & L 23 Series

-DPocket Width

6″

1-3/4″ 1/4″ 1-1/2″ 1-5/8″ ADI 3.3 lb. JD: Backhoe loading buckets with H & L 23 Seriestype adapters; Skid-Steer: JD14, JD24, JD24-A; Case: 480F, 580K, 580L, 590, 590L, 680L, 780D; Ford: 555D, 575D, 655D, 755B. 2-1/2″ 1/8″ 2-1/16″ 2-1/8″ ADI 8.8 lb. JD: 690, 690A, 690B, 690C, 690D, 690E; Competitive: Excavators with H & L 25 Series-type adapters (1-1/2″ edges).


John Deere

Fanggs Digging and Loading Teeth (Continued)

-A-

-B-

-C-

Length

Width

Point

-DPocket Width

-EPocket Height

Series

Tooth Part No.

Hensley 156 Series

TF156 (Digging)

1-3/4″ 1/8″ 1-5/8″ 1-5/8″ ADI 3.9 lb. JD: 300D, 310D, 315D, 410D, 500B, 510, 510D, 710B; Competitive: Backhoes with Hensley 156 Series-type adapters (1″ edges).

TF160 (Digging)

6-1/4″

TF220 (Digging)

7″

2-5/8″ 1/4″ 2-1/4″ 2-1/8″ Cast 6.0 lb. JD: 490, 490D, 490E, 495D, 590D, 595, 595D; Competitive: Backhoes and excavators with Hensley 220 Series-type adapters (1-1/4″ edges).

TF290 (Digging)

8-1/4″

TF310 (Digging)

7-1/2″

TF330 (Digging)

9-1/4″

TF350 (Digging)

10-5/8″

Pin

TF13P

Hensley 160 Series Pin

TP160


TP160


TK290


TP160L


TK330


TP400HD


6″

2-1/8″ 1/8″ 1-5/8″ 2-3/8″ Cast 4.2 lb. JD: 190E, 290D; Competitive: Backhoes and excavators with Hensley 160 Series-type adapters (1″ edges).

3-1/4″ 1/4″ 2-7/8″ 2-11/16″ Cast 10.4 lb. JD: 490, 490D, 490E, 495D, 590D, 595, 595D, 690, 690A, 690B, 690C, 690D, 690E; Competitive: Excavators with Hensley 290 Series-type adapters (1-1/2″ edges).

3-1/4″ 1/4″ 3″ 2-1/8″ Cast 10.4 lb. JD: 590D, 595, 595D, 690, 690A, 690B, 690C, 690D, 690E, 790, 790D, 790E, 792, 792D; Competitive: Excavators with Hensley 310 Series-type adapters (1-1/2″ edges). 3-5/8″ 1/4″ 3-13/32″ 3-3/16″ Cast 15.3 lb. JD: 590D, 595, 595D, 690, 690A, 690B, 690C, 690D, 690E, 790, 790D, 790E, 792, 792D; Competitive: Excavators with Hensley 330 Series-type adapters (1-1/2″ edges).

4-1/4″ 1/4″ 3-1/2″ 2-7/8″ Cast 23.6 lb. Competitive: Excavators with Hensley 350 Series-type adapters.


John Deere

Fanggs Digging and Loading Teeth (Continued) -A-

-B-

-C-

Width

Point

Series

Tooth Part No.

Length

Hensley 400 Series

TF400 (Digging)

9-1/4″

TF475 (Digging)

11-7/8″

Pin

TP400HD


TP475

5-3/4″ 1/4″ 4-3/4″ 3-1/2″ Cast 40.7 lb. JD: 890, 890A, 892D, 892E, 992D, 992E; Competitive: Excavators with Hensley 475 Series-type adapters (2-1/2″ edges).

Reference 2

John Deere

TF13 (Loading)

Pin

Ref. 2

John Deere

TF10L (Loading)

Pin Washer

Ref. 1

TF10P T112196

John Deere

TF11L (Loading)

Pin

Ref. 1

TP160L

John Deere

TF33L (Loading)

Pin Washer

Ref. 1

T67083 T67086


-EPocket Height

4-1/2″ 1/4″ 4″ 2-7/8″ Cast 19.7 lb. JD: 690, 690A, 690B, 690C, 690D, 690E, 790, 790D, 790E, 792, 792D, 890, 890A, 892D, 892E, 992D, 992E; Competitive: Excavators with Hensley 400 Series-type adapters (2″ edges).

Reference 1

TF13P

-DPocket Width

6-3/8″

2-5/8″ 1/8″ 1-1/2″ 1-1/8″ ADI 3.9 lb. Crawler Loaders: 1010, 2010, 350, 350A, 350B, 350C, 355D; Wheel Loaders: 310, 400, 401A, 401C, 410, 410B, 415B, 500, 500A, 500C, 510B, 515B, 610B, 710B, 710C, 710E

5-1/2″

3-5/8″ 1/8″ ADI 6.1 lb. 4-Wheel Drive Loaders: 544E, 544G, 544H, 624E, 624G, 644E, 644G; Crawler Loaders: 455G, 555G 3-5/8″ 1/8″ 2−3/8″ 1−3/4″ ADI 5.1 lb. 4-Wheel Drive Loaders: 444, 444C, 444CH, 444D, 544, 544A, 544B, 544C, 544D, 644, 644A, 644B, 644C, 644D; Compactors: 646, 646B, 646C; Crawler Loaders: 450, 450B, 450C, 455D, 455E, 555, 555A, 555B, 655, 755, 755A 6″

3-1/4″ 1/8″ 2−1/2″ 3−1/8″ Cast 15.0 lb. 4-Wheel Drive Loaders: 744E, 744H, 844; Crawler Loaders: 655, 655B, 755, 755A, 755B

9-5/8″


John Deere

Series

Pin Washer

Pin Washer

Chisel Teeth

-A-

-B-

-C-

Tooth Part No.

Length

Width

Point

T105690

5-7/8″

2″

T69647

9-1/8″

T112195 T112196

T67083 T67086


-DPocket Width

-EPocket Height

3/8″ 2-1/4″ 1-3/4″ Cast 4.7 lb. 4-Wheel Drive Loaders: 544E, 544G, 544H, 624E, 624G, 644E, 644G; Crawler Loaders: 455G, 555G 2-5/8″ 1/4″ 2-1/2″ 3″ Cast 10.5 lb. 4-Wheel Drive Loaders: 744E, 744H, 844; Crawler Loaders: 655, 655B, 755, 755A, 755B, 855


John Deere

Standard Teeth

Reference 1

Reference 2

Series

Tooth Part No.

John Deere

T103189

Pin Washer

T112195 T112196

John Deere Pin

Pin

John Deere Pin Washer

T29887

T56004

John Deere

T79008

John Deere Pin

TH106698

John Deere Pin

TP160


Point

-EPocket Height

3-11/16″ 3/16″ 2-1/4″ 1-3/4″ Cast 5.9 lb. 4-Wheel Drive Loaders: 544E, 544G, 544H, 624E, 624G, 644E, 644G; Crawler Loaders: 455G, 555G 2-13/16″ 1/4″ 2-3/8″ 1-3/4″ Cast 5.0 lb. 4-Wheel Drive Loaders: 444, 444C, 444CH, 444D, 544, 544A, 544B, 544C, 544D, 644, 644A, 644B, 644C, 644D; Compactors: 646, 646B, 646C; Crawler Loaders: 655, 755, 755A 4-5/8″ 7/16″ Cast 4-Wheel Drive Loaders: 844

3-3/16″ 2-1/4″ 13.1 lb.

4-1/8″ 3/16″ 2-1/2″ 3″ Cast 14.0 lb. 4-Wheel Drive Loaders: 744E, 744H, 844

5-1/2″ 2

U13449

34M7070

Width

-DPocket Width

9-1/8″ 1

Wedge Pin TH106699 Lock TH106700

Length

8″

1

T67083 T67086

-C-

5-3/4″ 1

T56005

-B-

5-9/16″ 1

TP160

John Deere

Ref.

-A-

2-1/4″ 3/16″ Cast Excavators: 70, 70D

1-7/8″

1-7/8″ 3.1 lb.

4-5/16″ 1

U16086

2-5/8″ 3/16″ 1-1/2″ 1-1/8″ Cast 2.2 lb. Crawler Loaders: 1010, 2010, 350, 350A, 350B, 350C, 355D; Wheel Loaders: 310, 400, 401A, 401C, 410, 410B, 415B, 500, 500A, 500C, 510B, 515B, 610B, 710B, 710C, 710E

5-3/8″ 1

3-5/8″ 5/16″ 2-3/8″ 1-3/4″ Cast 4.5 lb. 4-Wheel Drive Loaders: 444, 444C, 444CH, 444D, 544, 544A, 544B, 544C, 544D, 644, 644A, 644B, 644C, 644D; Crawler Loaders; 450, 450B, 450C, 455D, 455E, 555, 555A, 555B; Scraper Bowls: 760, 760A, 762, 762A, 762B, 860, 860A, 860B, 862, 862B


John Deere

Reference 1

Standard Bolt-On Teeth

Reference 2

Reference 3

-ALength Series

Tooth Part No.

John Deere

AT121474

Ref.

Center

John Deere

John Deere

John Deere

T110052

John Deere

T110058

John Deere

T111297

-DHole Spacing

-EWt.

12-3/4″ 2″ 3/16″ 2-5/8″ 7-1/4″ 23˚ 4″ JD: 344E, 344H, 444E

15/16″ 9.9 lb.

4

12-3/4″ 2-3/8″ 1/4″ 2-5/8″ 7-1/4″ 23˚ 4″ JD: 344E, 344H, 444E

15/16″ 13.7 lb.

4

12-3/4″ 2-3/8″ 1/4″ 2-5/8″ 7-1/4″ 23˚ 3-7/8″ JD: 344E, 344H, 444E

15/16″ 14.0 lb.

2

9-1/2″ 2-3/8″ JD: 50

1-5/8″

1/4″ 4-7/8″ 1-3/4″

11/16″ 5.7 lb.

2

8-1/4″ 2″ JD: 30

1-3/8″

1/4″ 3-3/4″ 1-3/4″

5/8″ 3.9 lb.

8″

1-1/4″

1/4″

9/16″ 3.5 lb.

2-1/2″ 60˚

1/4″ 5-1/4″ 3-1/2″

AT121476 Corner, Left-Hand

-G-

-CPoint

3

AT121475 Corner, Right-Hand

-F-

-BWidth

Reference 4

2

4″

JD: 15

John Deere


T115680

1

9-3/4″ 2-1/2″ JD: 84


5/8″ 6.1 lb.

John Deere

Adapters

Reference 1

Reference 2

Reference 3

Reference 4

Reference 5

Reference 6

Reference 7



John Deere

Adapters

Note: John Deere adapter and teeth applications are listed on pages 10-11.

Adapter Part No.

Type Attachment

B

C

D

Hole Spacing

Wt. (lb.)

T103190

Bolt-On Center

1

7-3/4″

1-1/4″

4-3/4″

30˚

4-13/16″

14.4

T103191

Bolt-On Corner

2

8-1/4″

1-1/4″

1-3/4″

30˚

T104673

Bolt-On Center

3

7-7/16″

1-5/16″

8-15/16″

30˚

4-11/16″

27.0

T104674

Bolt-On End

2

8-15/6″

1-1/4″

2-3/4″

30˚

4-13/16″

33.6

T105692

Bolt-On Center

1

5-5/8″

1″

3-5/8″

30˚

3-5/8″

10.6

T112163

Bolt-On Corner

2

5-5/8″

1″

1-5/8″

30˚

T112164

Bolt-On Center

1

5-7/8″

3/4″

4″

30˚

3-5/8″

9.5

T123077

Bolt-On Center

3

9-1/4″

1-1/2″

10-1/2″

30˚

5-3/16″

40.4

T29886

Bolt-On

1

8-1/4″

1-3/8″

4″

30˚

6″

12.6

T35385

Bolt-On

1

8-5/8″

1-1/2″

5-7/16″

32˚

5-1/4″

14.7

T38783

Bolt-On

5

8-3/8″

1-1/8″

9-7/8″

30˚

2″

12.3

T56003

Bolt-On

3

8-1/4″

1-15/16″

10-1/2″

30˚

5″

36.7

T79004

Bolt-On Center

3

8-9/16″

1-13/16″

11-1/4″

30˚

5-3/16″

38.2

T79006

Bolt-On Corner

2

11-13/16″

1-1/2″

2-3/8″

30˚

57.2

TH106697

Weld-On

7

1-7/8″

15/16″

5-1/4″

30˚

6.6


Ref.

A


23.2

14.2

John Deere Adapter Part No.

Adapters (Continued) Type Attachment

Ref.

B

C

D

Hole Spacing

Wt. (lb.)

U16087

Bolt-On

6

7-1/2″

1-1/2″

8-1/8″

35˚

2″

9.3

U16864

Bolt-On

1

8-5/8″

1-1/8″

3-7/8″

32˚

6-1/2″

10.3

U41344

Bolt-On

1

4-7/16″

1-1/8″

3-3/8″

30˚

2-3/8″

5.2

A

Adapter Hardware Adapter

Bolt Size

Bolt

Nut

Washer

T103190

1″ x 3-1/8″

19M7287

14M7278

24M7243

T103191

1″ x 3-1/2″

19M8288

14M7278

24M7243

T104673

1″ x 4-1/4″

19H3556

K40018

T75690

T104674

1-1/4″ x 4-1/4″

19H3594

A20329

T81065

T105692

3/4″ x 2-1/2″

19M8102

14M7277

24M7242

T112163

1″ x 3-1/2″

19M8288

14M7278

24M7243

T112164

3/4″ x 2-1/2″

19M8102

14M7277

24M7242

T123077

1-1/4″ x 5″

08H4815

A20329

T79096

T29886

5/8″ x 3-1/4″

19H2072

K40015

24H1367

T35385

3/4″ x 2-1/4″

19H1782

K40016

24H1400

T38783

3/4″ x 4″

T70287

14H1046

T83426

T56003

7/8″

–

_

_

T79004

1-1/4″

–

–

–

T79006

1-1/4″ x 4-1/2″

08H4814

A20329

T79096

U16087

3/4″ x 4″

T70287

14H1046

12H236

U16864

5/8″ x 3-1/4″

10H1157

K40015

24H1367



John Deere Hardware Illustrated parts are actual size.

TF10P

T112196

T112195

TT9J2308 T3G9609

TH106700

TH106699



John Deere Hardware Illustrated parts are actual size.

34M7070

TF13P

TP160

TP160L

T56005



John Deere Replacement Teeth for Caterpillar Products Oversized Pocket and Extended Adapter Nose Piece The John Deere replacement teeth for Caterpillar products come in sizes and types to fit almost all machine makes and models. The oversized pocket characteristics of these teeth with the extended adapter nose piece provide a nose fit between the tooth and adapter which results in strong impact resistance but a loose fit in the ramps.

Pin and Washer Retention Replacement teeth for Caterpillar equipment use a 2-piece retention method which makes tooth removal and installation fast and easy. Both the pin and the washer are reusable. The original style and "E" style are now available. Original Style Pins and Washers The original retention for replacement Caterpillar teeth use a horizontal pin and split washer. Do not use the new "E" washers with the original style pins. "E" Pins and Washers

Centerline Design, Oversized Pocket . Nose fit provides impact resistance with loose pin and ramp fit.

"E" Pins and Washers have an "E" in the Part No.

The shallow radius groove on the "E" pin reduces the spread which increases locking force. The tapered pin outer edge reduces contact with the inside of the adapter counterbore. This minimizes breakage. The new pin jacket on the washer aligns the pin and washer during installation. Do not use split washers with "E" washers with "E" pins. "E" pins and washers are interchangeable with original pins/washers in all sizes except J450/J460 adapters. Original pins/washers fit J450 adapters. "E" pins/washers fit J460 adapters

John Deere Replacement Teeth for Caterpillar Products Various information can be determined from the part numbering system. Refer to the following chart for basic part number information. Part Number Explanation (Replacement Teeth for Caterpillar Products) P r e f i x and S u f f I x Explanation NOTES: PM or T 0 Flare PM or T 1 Short The "Series" equipment the PM or T 2 Long tooth is used on is generally PM or T 2 Heavy Duty Long provided in the part number. PM or T 3 Abrasion PM or T 9 Penetration "N" within the part number PM or TT T Tiger designates heavy-duty. PM or TX WT Twin Tiger TF D Fanggs Digging See examples below. TF L Fanggs Loading PM SYL Ribbed Sharp PM RC Rock Chisel PM RP Rock Penetrator Examples: T3G8250 Flare Tooth used with 25 Series Adapters (T3G8250) T9N4252 Long (Heavy-Duty) used with 25 Series Adapters (T9N4252) T9N4353 Abrasion Tooth used with 35 Series Adapters (T9N4353) T1U3551 Short Tooth used with 55 Series Adapters (T1U3551) TF1U3252D Fanggs Digging used with 25 Series Adapters (TF1U3252D)

John Deere Replacement Teeth for Caterpillar Products - Types Available

• •

Fanggs Digging Teeth (Non-Centerline) TF_D Part Numbers For general-purpose to heavy-duty digging conditions. Provide a clean start and close crowd.

• •

Fanggs Loading Teeth (Non-Centerline) TF_L part Numbers For general-purpose to heavy-duty digging conditions. Flat bottom for improved bucket control.

• •

•

Short Teeth (Centerline) PM or T_1 Part Numbers Designed for use in highimpact and pry-out work. Provides more strength but less wear than the long tooth Long Teeth (Centerline) PM or T_2 Part Numbers For loading and digging


Tiger Teeth (Non-Centerline) PM or TT_T Part Numbers • Long, aggressive teeth designed for breaking extremely tight soil. • Used primarily as center teeth

Penetrator Teeth (Non-Centerline) PM or T_9 Part Numbers • Use in highly compacted, dense material such as clay. • Center rib provides added strength. • Maintains good sharpness throughout its life.

Twin Tiger Teeth (Non-Centerline) PM or TX_WT Part Numbers • For densely compacted material. • Use primarily as a corner tooth but can be used in center.

Abrasion Teeth (Standard and Heavy-Duty) (Non-Centerline) PM or T_3 Part Numbers • Use where extended tip life is needed in highly-abrasive conditions. • Heavy-duty teeth have more wear material than the standard teeth.

•

• • •

Flare Teeth (Centerline) PM or T_0 Part Numbers Work extremely well in loose and mud-like conditions.

Ribbed Sharp (Centerline) PM _SYL Part Numbers Excellent Penetration Greater Wearlife than tiger For digging in tight or compacted material


• •

Rock Chisel (Non-Centerline) PM _RC Part Numbers Extremely abrasive terrain requiring extra penetration. Increased Wear Material

•

Rock Penetrator (Non-Centerline) PM _RP Part Numbers Loaders in high abrasion quarry and mining operations. .

• •

H.D. Long (Non-Centerline) PM or T_2 Part Numbers Use in high abrasion application Added wear material in tip for longer wear life.

Replacement for Caterpillar Products Illustrated parts are actual size

Retainers

T8E6208 T8E6209

20 Series Fanggs

TF1U3202P T4T0001

20 Series except Fanggs


Retainers (Continued)

T6Y3228 22 Series

T8E6259 22, 25 Series

T9J2258 25 Series

T8E6258 25 Series

T3G9609 25, 30 Series

T9J2308 30 Series


T7T3409 40 Series


T7T3408 40 Series

T9J2358 35 Series T8E6359 35 Series

T8E6358 35 Series T3G9549 35 Series


T3G9549 35, 45 Series

T1U1458 45 Series (J450 Adapters)


T8E8469 45 Series

T8E0468 45 Series (J460 Adapters)

Replacement for Caterpillar Products


Illustrated parts are actual size

T3G9559 55 Series

T1U1558 55 Series

Caterpillar - Tooth by Series

a

20 Series g m d j a f -

a

Fanggs dig long tiger twin tiger abrasion penetrator org pin org wash e type pin e type wash adapter adapter

TF1U3202 T1U3202 TT1U3202 TX1U320WT T4T2203 T1U3209 TF1U3202P T4T0001 T8E6208 T8E6209* PM4T1204 T8J7525

ü ü ü ü ü ü ü ü ü ü ü ü

Cat flush weld-on: 416, 910, 931 Cat center weld-on bottom strap: 416, 426, 428, 436, 438, 910, 914G, 931, 935

22 Series style m -

description long e type pin e type wash adapter

part no. T6Y3222 T6Y3228 T8E6259 PM6Y3224

disc. used on ü ü ü ü Cat weld-on double strap: 446, 933, 307, 307B

Caterpillar - Applications 25 Series style g c h m d k j l f e a b -

description Fanggs dig Fanggs load short long long h-d tiger twin tiger flare penetrator abrasion h-d abrasion ribbed sharp org pin org wash e type pin e type wash adapter adapter adapter

part no. TF1U3252D TF1U3252L T1U3251 T1U3252 T9N4252 TT1U3252 TX1U3252WT T3G8250 T9J4259 PM9N4253 T4T2253 PM1U3252SYL T9J2258 T3G9609 T8E6258 T8E6259 T25CA T25EA T1U1254

disc. ü ü ü ü ü ü ü ü ü ü ü ü ü ü ü ü ü ü ü

used on

-

adapter

T3G0169

ü

Cat center weld-on: 205, 206, 211, 212, 213B, 214B, 916, 920, 926, 930, 936, 941, 941B, 951, 951C, 953, 953B, 953C

-

adapter

T1U0257

ü

Cat center bolt-on: 916, 920, 924F, 926, 928, 930, 936, 938F, 938G, 939, 941, 941B, 943, 943LPG, 951, 951C, 953, 953B, 953C

-

adapter

PM3G4258

ü

Cat left bolt-on: 916, 920, 924F, 926, 928, 930, 936, 938F, 938G, 939, 941, 941B, 943, 943LPG, 951, 951C, 953, 953B, 953C

-

adapter

PM3G4259

ü

Cat right bolt-on: 916, 920, 924F, 926, 928, 930, 936, 938F, 938G, 939, 941, 941B, 943, 943LPG, 951, 951C, 953, 953B, 953C

-

adapter

PM6Y3254

ü

Cat center weld-on: 311, 312, 311B, 312B, 312BL

J D center bolt-on: 544E, 544G, 544H, 624E, 624G, 624H J D center bolt-on: 544E, 544G, 544H, 624E, 624G, 624H Cat flush weld-on: 205, 206, 211, 212, 213B, 214B, 918F, 920, 926, 928, 936, 953, 951, 953B, 953C

Caterpillar - Applications 30 Series style g c h m d k j l f e a b n -

description Fanggs dig

part no. TF1U3302D

disc. used on ü ü ü ü ü ü ü ü ü ü ü ü

-

Fanggs load short long long h-d tiger twin tiger flare penetrator abrasion h-d abrasion ribbed sharp rock chisel org pin org wash adapter adapter adapter

TF1U3302L T1U3301 T1U3302 T9N4302 TT1U3302 TX1U3302WT T107-3300 T9J4309 T9N4303 T4T2303 PM1U3302SYL PM1U3302RC T9J2308 T3G9609 T30CA T30EA T3G6304

-

adapter adapter adapter

T1U0307 PM3G4308 PM3G4309

ü ü ü

-

adapter adapter adapter adapter adapter

T4T4307 PM3G9307 PM3G8308 PM3G8309 PM1U1304

ü ü ü ü ü

ü ü ü ü ü

JD center bolt-on: 644E, 644G, 644H, JD end bolt-on: 644E, 644G, 644H, JD double strap center: 690E, Cat double strap center: 215, 219, 315, 315B, 315BL, 320, 320B Cat center bolt-on: 944, 950, 953B, 955 Cat 1 - 1-1/4" edge left bolt-on: 950B, 955, 960F, 963 Cat 1 - 1-1/4" edge right bolt-on: 950B, 950E, 950F, 950G 955, 960F, 962G, 963 Cat center bolt-on: 950, 953B, 955, 960F, 963 Cat center bolt-on: 966, 966C, Cat 1-1/4" edge left bolt-on : 962G, 966, 966C Cat 1-1/4" edge right bolt-on : 962G, 966, 966C Cat flush weld-on: 944, 950, 955, 966

Caterpillar - Applications 35 Series style g h m d k j l f e a b n I -


part no. TF1U3352D

disc. used on ü ü ü ü ü ü ü ü ü ü ü

short long long h-d tiger twin tiger flare penetrator abrasion h-d abrasion ribbed sharp rock chisel rk penetrator org pin org wash e type pin e type wash adapter

T1U3351 T1U3352 T9N4352 TT1U3352 TX1U3352WT T107-3350 T9J4359 T9N4353 T4T2353 PM1U3352SYL PM1U3352RC PM4T2353RP T9J2358 T3G9549 T8E6358 T8E6359 T3G8354

-

adapter

PM1U1354

ü

Cat flush weld-on: 245, 950, 950B, 963B, 966C, 966D, 966E, 966F, 973, 973LPG, 977, 977L, 980, 980B

-

adapter adapter

PM8J5357 T3G3357

ü ü

Cat center bolt-on: 963, 966

-

adapter

PM3G5358

ü

Cat cornergaurd LH: 960F, 966, 966D, 966E, 966F, 970, 970F, 973, 973LPG, 977, 977L,

-

adapter

PM3G5359

ü

Cat cornergaurd RH:960F, 966, 966D, 966E, 966F, 970, 970F, 973, 973LPG, 977, 977L,

-

adapter adapter adapter adapter

PM8J3357 PM1U1357 PM1U1350 PM9J2357

ü ü ü ü

ü ü ü ü ü

JD double strap center: 790D, 892D, 892E, Cat double strap center: 215, 219, 225, 229, M318, 320, 320B, 320BL, 322, 322B, 322BL, 325BL, 325B, 325

Cat center bolt-on: 960F, 966, 966D, 966E, 966F, 970, 970F, 973, 973LPG, 977, 977L

Cat Center Bolt-on: 980C, 980F Cat Center Bolt-on: Spade Nose 980C

Caterpillar - Applications 40 Series style m d f f n -

description long long h-d penetrator penetrator rock chisel org pin org wash e type wash adapter

part no. T7T3402 T8E4402 T6Y7409 PM6Y7409 PM7T3402RC T7T3408 T7T3409 T8E8409 PM7T3404

disc. used on ü ü ü ü ü ü ü ü

Cat double strap center: 320L, 325L, 330L, 322L, 330BL, 345B, 345BL, 320BL, 322BL, 325BL, 320B, 322B, 325B, 330B, 320, 322, 325, 330

Caterpillar - Applications 45 Series style g h m d k j l f a e b n I -


part no. TF9W8452D

disc. used on ü ü ü ü

T9W8451 T9W8452 T9N4452 PM1U3452T PM1U3452WT T107-3450 T9W8459 PM9W1453 T9N4453 PM9W8452SYL PM1U3452RC PM9W1453RP T1U1458 T3G9549 T8E0468* T8E8469* T1U1454

-

short long long h-d tiger twin tiger flare penetrator abrasion abrasion h-d ribbed sharp rock chisel rk penetrator org pin org wash e type pin e type wash adapter adapter

T8E6464**

ü

Cat double strap center: 229, 235, 330, 330B, 330BL, 345, 345BL, 350, 350L

-

adapter

PM8E3464**

ü

Cat spade nose double strap center weld-on: 973SLAG, 983, 988, 988B

-

adapter PM8E3465** ü Cat spade nose double strap RH: 983, 988, 988B adapter PM8E3466** ü Cat spade nose double strap LH: 983, 988, 988B adapter PM8J1454 ü adapter PM9J9584 ü Cat flush mount weld-on: Note: All 45 Series adapter will not accept e-type pins and retainers * used on J460 adapters only ** J460 adapter

ü ü ü ü ü

ü ü ü ü ü

JD double strap center: 790D, 790E, 892D, 892E, 992, 992D

Caterpillar - Applications 55 Series style h m d f e n I -

description short long long h-d penetrator abrasion h-d rock chisel rk penetrator org pin org wash e type pin e type retainer adapter adapter adapter adapter

part no. T1U3551 T1U3552 PM9N4552 T9J4559 PM6Y2553 PM1U3552RC PM9W1553RP T1U1558 T3G9559 T6Y8558 T8E5559 PM1U1553 PM3G9494 PM3G9495 PM3G9496

disc. used on ü ü ü ü ü

part no. T4T4702 PM4T4703 T4T4707 T9U9616 T4T4704

disc. used on ü ü ü ü ü Cat double strap: 375, 375L, 375LME, Deere double strap: 550LC, 750

ü ü ü ü ü ü ü ü

Cat double strap: 245, 345, 345B, 345BL, 350, 350L, 375 Cat double strap center: 245FS Cat double strap RH: 245S Cat double strap LH: 245S

70 Series style m a -

description long abrasion washer pin adapter

CATERPILLAR LOADER TIPS VERTICAL-PIN STYLE (OLD STYLE) MODEL NO.

SHORT TIP

920, 922, 930, 931, 933, 941, 944

LONG TIP

PIN

LOCK

PM4K6936

PM4K0043

PM4K0041

930, 944, 950, 951, 955, 966

PM5K2925

PM4K0034

PM4K0043

PM4K0041

950, 966, 977, 980

PM5K2926

PM4K6148

PM4K0032

PM4K0008

Caterpillar - Specifications

T

20 Series style T T T T T T 2 3

description Fanggs dig long tiger twin tiger abrasion penetrator adapter adapter

part no. TF1U3202 T1U3202 TT1U3202 TX1U320WT T4T2203 T1U3209 PM4T1204 T8J7525

a 5-7/8" 5-11/16" 6-1/2" 6-1/2" 5-11/16" 5-11/16" 7-1/4" 3-15/16"

b 1-3/4" 2" point 2-3/4" 2-3/16" 1" 1/2" 1"

c 1-13/32" 1-13/32" 1-13/32" 1-13/32" 1-13/32" 1-13/32" 1/2" 1"

d 1-27/32" 1-27/32" 1-27/32" 1-27/32" 1-27/32" 1-27/32" 23° 23°

lbs. 4.1 3 3.5 5.5 3 2.4 4.6 3.1

a 6-9/16" 5-9/16"

b 2-1/8" 3-11/16"

c 1-3/4" 1-1/16"

d 2-11/32" 22°

lbs. 3.7 6.6

22 Series style description part no. T long T6Y3222 1 adapter PM6Y3224

Caterpillar - Specifications 25 Series style T T T T T T T T T T T T 4 5 2 3 4 6 6 1

description part no. Fanggs dig TF1U3252D fanggs load short long long h-d tiger twin tiger flare penetrator abrasion abrasion h-d ribbed sharp adapter adapter adapter adapter adapter adapter adapter adapter

TF1U3252L T1U3251 T1U3252 T9N4252 TT1U3252 TX1U3252WT T3G8250 T9J4259 T4T2253 PM9N4253 PM1U3252SYL T25CA T25EA T1U1254 T3G0169 T1U0257 PM3G4258 PM3G4259 PM6Y3254

a 7-5/8" 7-5/8"

b 2-1/2" 2-1/2"

c 1-15/16" 1-15/16"

d 2-11/16" 2-11/16"

6-11/16" 7-3/4" 8-1/8" 8-1/8" 8-1/8" 8" 7-1/2" 7-1/2" 7-15/16" 8-1/4" 5-5/8" 8-1/4" 9-1/4" 7-1/2" 2-3/4" 5-3/4" 5-3/4" 6-1/8"

2-1/4" 2-5/8" 2-2/1" point 3-1/8" 4-1/2" 1-3/8" 3-1/8" 3-15/16" 2-3/4" 1" 1" 2" 2-5/16" 4-7/8" 4-3/16" 4-3/16" 5"

1-15/16" 1-15/16" 1-15/16" 1-15/16" 1-15/16" 1-15/16" 1-15/16" 1-15/16" 1-15/16" 1-15/16" 7-1/8" 3-1/8" 1" 2" 1-1/16" 1-1/16" 1-1/16" 1-5/16"

2-11/16" 2-11/16" 2-11/16" 2-11/16" 2-11/16" 2-11/16" 2-11/16" 2-11/16" 2-11/16" 2-11/16" 30° 30° 22° 22° 23° 43° 43° 22°

lbs. 9 9 5.9 5.9 10.9 5.5 7.3 8.5 5.3 7 10 6.2 14.2 18.6 12.1 10.8 18.2 25 25 9.5

Caterpillar - Specifications 30 Series style T T T T T T T T T T T T T 4 5 1 4 6 6 4 4 6 6 2

description part no. Fanggs dig TF1U3302D Fanggs load short long long h-d tiger twin tiger flare penetrator abrasion abrasion h-d ribbed sharp rock chisel adapter adapter adapter adapter adapter adapter adapter adapter adapter adapter adapter

TF1U3302L T1U3301 T1U3302 T9N4302 TT1U3302 TX1U3302WT T107-3300 T9J4309 T4T2303 T9N4303 PM1U3302SYL PM1U3302RC T30CA T30EA T3G6304 T1U0307 PM3G4308 PM3G4309 T4T4307 PM3G9307 PM3G8308 PM3G8309 PM1U1304

a 9" 8-3/4"

b 3" 3"

7-5/8" 8-3/4" 8-7/8" 9-3/8" 9-1/8" 8-1/2" 8-1/2" 8" 8-5/16" 9-1/4" 9-7/8" 2-5/16" 10" 7-7/8" 2-3/4" 7" 7" 3-3/16" 3-1/8" 8-3/16" 8-3/16" 9-1/4"

2-3/4" 2-3/4" 2-3/4" 3-1/4" 4" 6" 1-1/2" 3-7/16" 4-3/8" 3-1/2" 3-1/4" 4-13/16" 4-1/8" 4-3/8" 4-7/8" 4-3/4" 4-3/4" 6-1/2" 6-5/16" 5-1/2" 5-1/2" 3-3/4"

c 2-3/8" 2-3/8" 2-3/8" 2-3/8" 2-3/8" 2-3/8" 2-3/8" 2-3/8" 2-3/8" 2-3/8" 2-3/8" 2-3/8" 2-3/8"

d 3-1/32" 3-1/32" 3-1/32" 3-1/32" 3-1/32" 3-1/32" 3-1/32" 3-1/32" 3-1/32" 3-1/32" 3-1/32" 3-1/32" 3-1/32"

1-5/16" 1-1/16" 1-3/8" 1-1/16" 1-1/16" 1-1/16" 1-5/16" 1-5/16" 1-1/16" 1-1/16" 1-1/2"

30° 30° 22° 39° 39° 39° 23° 23° 39° 39° 23°

lbs. 12.3 13.3 9 9.9 12.1 9.2 10.7 11 7.8 10.8 16.7 10 11.8 20.8 21.7 16.3 23.1 34.9 34.9 31.2 31.9 36.5 36.5 18.3

Caterpillar - Specifications 35 Series style T T T T T T T T T T T T T 1 2 7 4 6 6 7 4 3 7

description part no. Fanggs dig TF1U3352D short long long h-d tiger twin tiger flare penetrator abrasion abrasion h-d ribbed sharp rock chisel rk penetrator adapter adapter adapter adapter adapter adapter adapter adapter adapter adapter

a 10"

b 3-3/8"

T1U3351 T1U3352 T9N4352 TT1U3352 TX1U3352WT T107-3350 T9J4359 T4T2353 T9N4353 PM1U3352SYL PM1U3352RC PM4T2353RP T3G8354 PM1U1354 PM8J5357 T3G3357 PM3G5358 PM3G5359 PM8J3357 PM1U1357 PM1U1350 PM9J2357

8-1/8" 9-3/8" 10" 11-1/8" 11-1/2" 9-1/2" 9-7/8" 9-1/2" 10 10 1/4" 11" 11-5/8" 8-1/4" 11-1/4" 4-3/16" 3-7/8" 8-17/32" 8-17/32" 3-1/2" 4-1/8" 10-1/4" 3-3/8"

3-1/2" 3-1/4" 3-1/2" 3-15/16" 4-3/4" 7" 2" 4" 5" 2" 3-1/2" 3-3/4" 2-11/16" 3-3/4" 6" 5-7/8" 5-5/8" 5-5/8" 5-11/16" 6-1/8" 2" 5-3/4"

part no. T7T3402 T8E4402 T6Y7409 PM6Y7409 PM7T3402RC PM7T3404

a 11-1/16" 11-1/16" 10-1/2" 11-3/8" 12" 9-1/2"

b 3-7/8" 3-7/8" 2" 1-1/2" 4" 6-3/4"

c 2-11/16" 2-11/16" 2-11/16" 2-11/16" 2-11/16" 2-11/16" 2-11/16" 2-11/16" 2-11/16" 2-11/16"

d 3-5/16" 3-5/16" 3-5/16" 3-5/16" 3-5/16" 3-5/16" 3-5/16" 3-5/16" 3-5/16" 3-5/16"

2-11/16" 2-11/16" 2-11/16" 1-5/8" 1-1/2" 1-13/16" 1-11/16" 1-9/16" 1-9/16" 1-13/16" 1-3/4" 1-3/4" 1-1/2'

3 5/16" 3-5/16" 3-5/16" 35° 22° 23° 24° 38° 38° 23° 23° 23° 23°

lbs. 16.9 11.4 12.3 18.7 13 14.2 16 12.3 17.8 21.6 12.4 15.3 23 20.7 30.9 35.6 40.3 49 49 44 45 21 36.4

c 3-5/32" 3-5/32" 3-5/32" 3-5/32" 3-5/32" 1-7/8"

d 3-21/32" 3-21/32" 3-21/32" 3-21/32" 3-21/32" 22°

lbs. 25 25 21 17.5 23.5 6.7

40 Series style T T T T T 1

description long long h-d penetrator penetrator rock chisel adapter

Caterpillar - Specifications 45 Series style T T T T T T T T T T T T T T 1 1 2 2 1 1 1

description part no. Fanggs dig TF9W8452D short long long h-d tiger twin tiger flare penetrator abrasion h-d abrasion penetrator ribbed sharp rock chisel rk penetrator adapter adapter adapter adapter adapter adapter adapter

a 10"

b 3-3/8"

T9W8451 T9W8452 T9N4452 PM1U3452T PM1U3452WT T107-3450 T9J4459 T9N4453 PM9W1453 T9J4459 PM9W8452SYL PM1U3452RC PM9W1452RP T1U1454 T8E6464 PM8J1454 PM9J9584 PM8E3464 PM8E3465 PM8E3466

10-3/8" 11-1/2" 13" 13-3/16" 13-3/16" 11-1/4" 11-5/8" 11 5/8" 11-5/8" 11-5/8" 12-1/2" 13-5/16" 14" 11-1/8" 11-1/8" 12-1/2" 12-1/2" 10-3/8" 10-3/8" 10-3/8"

4-1/2" 4-1/2" 4-1/2" 5-1/2" 7-1/4" 9" 2" 5-1/2" 5-1/2" 2" 4-3/4" 4-1/2" 4-3/4" 7-3/8" 7-3/8" 4-1/8" 4-1/8" 6-7/8" 6-7/8" 6-7/8"

part no. T1U3551 T1U3552 PM9N4552 T9J4559 PM9W1553 PM6Y2553 PM1U3552RC T9J4559 PM9W1553RP PM1U1553 PM3G9494 PM3G9495 PM3G9496

a 12-1/2" 13-1/2" 14" 13-1/4" 13" 13-1/2" 14-3/4" 13" 15-3/16" 14-1/2" 14-1/2" 15" 15"

b 5-1/2" 5-1/2" 5-3/4" 2-5/8" 9" 7-5/8" 5-3/4" 2-5/8" 5-3/4" 8-5/8" 12-5/8" 13-3/8" 13-3/8"

c 3-17/32" 3-17/32" 3-17/32" 3-17/32" 3-17/32" 3-17/32" 3-17/32" 3-17/32" 3-17/32" 3-17/32" 3-17/32" 3-17/32" 3-17/32" 3-17/32"

d 3-29/32" 3-29/32" 3-29/32" 3-29/32" 3-29/32" 3-29/32" 3-29/32" 3-29/32" 3-29/32" 3-29/32" 3-29/32" 3-29/32" 3-29/32" 3-29/32"

lbs. 28.5 22.5 24.6 36.2 20.5 24.5 31.3 23.6

2" 2" 2-3/16" 2-3/16" 2-1/8" 2-1/8" 2-1/8"

24° 24° 23° 23° 22° 22° 22°

32.4 23.6 25.1 32.3 48.4 42 41.8 45.4 50 50 50 50

c 4-5/16" 4-5/16" 4-5/16" 4-5/16" 4-5/16" 4-5/16" 4-5/16" 4-5/16" 4-5/16" 2-7/16" 2-5/8" 2-5/8" 2-5/8"

d 4-11/32" 4-11/32" 4-11/32" 4-11/32" 4-11/32" 4-11/16" 4-11/16" 4-11/16" 4-11/16" 23° 22° 22° 22°

lbs. 35.5 33.5 59 35 50.5 67 45.5 32 66 77.2 70 70 70

55 Series style T T T T T T T T T 1 1 1 1

description short long long h-d penetrator abrasion abrasion h-d rock chisel penetrator rk penetrator adapter adapter adapter adapter

Caterpillar - Specifications 70 Series style T T 1

description part no. long T4T4702 abrasion T4T4703 adapter T4T4704

a 16-5/16" 16-5/16" 12-3/4"

b 7 9 16-3/4"

c 6 6 3"

d 5-3/4" 5-3/4" 22°

lbs. 84 107.2 149

John Deere Replacement Teeth for Esco Conical Products John Deere replacement teeth for Esco conical systems come in sizes and tooth designs to fit almost all machine makes and models. Conical Design The "conical" design mating system between tooth and adapter creates self-tightening action. The raised center area on the top and bottom of the adapter nose piece fits tightly into the formed area on the top and bottom of the tooth pocket. This design reduces tooth movement both vertically and horizontally. The tooth and adapter are designed as a bucket tooth system that will absorb impact loads and generally reduce the amount of abrasive action to the bucket lip.

Part Number Explanation Prefix Suffix PM TF PM TL T AP T R T S T S_F T TVIP or TVIPA

Pin and Lock Retention All John Deere replacement teeth for Esco conical products are retained with a pin and lock. Once the pin and lock are installed, a snug fit gives this attaching system little to no movement and provides great strength throughout the life of the tooth. We offer pins and locks in the standard and ratchet version. The standard is designed for use in general-purpose applications. The ratchet style provides secure retention in more demanding conditions and avoids "pin walk" in heavy prying conditions.

(Replacement Teeth for Esco Products)

Explanation NOTES: Nose Sizes are identified by the Dual Purpose Flare first two numeric Dual Purpose Long digits of the Abrasion Paneled designation number. Rock The letter(s) following Sharp the nose size describe Sharp_" Flare the tooth shape. Twin "V-Shaped" Paneled (Twin Tiger) T VIP or VIPA "V-Shaped" Paneled (Tiger) Examples: Part Number T30S Esco Replacement, 3.0 inches wide, sharp. Part Number T25S5F Esco Replacement, 2.5 inches wide, sharp, 5" flare.

John Deere Replacement Teeth for Esco Conical Products - Types Available

Abrasion-Paneled Teeth (AP Suffix) (Centerline)

Flare Teeth (S_F Suffix) (Centerline)

Sharp Teeth (S Suffix) (Centerline)

•

•

• Slim, penetrating profile. For use in general-purpose to heavy digging and loading conditions.

•

Good for general-purposeto-to heavy-duty applications. Good penetration; self sharpens.

For loading and digging in loose, mud-like conditions.

Tiger Teeth (VIP or VIPA Suffix) (Non-Centerline)

Twin Tiger Teeth (TVIP or TVIPA Suffix) (Non-Centerline)

•

•

•

V-shaped and paneled for highimpact digging and loading. Narrow bit for maximum penetration; paneled to maintain sharpness.

•

Two points on the V-shaped tooth cut clearance for bucket sides. Can be used as center teeth for maximum penetration.

Esco Conical - Teeth by Series

18 Series Conical style description a sharp c tiger b twin tiger tilt front long - std pin pin - std retainer - adapter tooth, long rubber lock adpt., W-O, bttm. leg, 1.25" lip adpt., B-O, 1-1/2 leg, (Case W18, W20) adpt., B-O, 2 leg, (Case 850B) adpt., B-O, crnr., RH (Case 850B) adpt., B-O, crnr., LH (Case 850B) adpt., B-O, 1-1/2 leg, 1.06" thr

part no. PM18SLHX PM18VIPHX PM18TVIPHX PM18THX PM18TL PM18PN PM18-20MPNP PM18LK PM833-18 PM18LPHX PM18-20MLKR PM855-18HX PM4718-18HX PM4729-18HX PM5701R-18HX PM5701L-18HX PM5707-18HX

rcv. disc.

part no. T25S T25VIP T25TVIP T25S5F PM25TF T2530PN T2530LK T2530PNR T2530LKR PM855-25 PM3806-25 PM25THX PM25RP PM25RB PM25RBS PM4703-25HX PM5710L-25HX PM5710R-25HX PMEWN25

rcv. disc. 9 9 9 9 9 9 9 9 9 9 9

9 9 9 9

non stock STK STK STK STK STK STK STK STK STK STK STK N.S. N.S. N.S. N.S. N.S. STK

used on

Competitive: Backhoes

25 Series Conical style a c b d d -

description sharp tiger twin tiger flare, 5" d-p flare std pin std retainer ratchet pin ratchet retainer adpt., W-O, bttm., leg, 1.25 lip, 30 degrees adapter tooth, tilt front pin, solid rubber bushing steel bushing adpt., B-O, 1-1/2 leg, (Case 1150) adpt., B-O, crnr., LH adpt., B-O, crnr., RH nose, W-O

non stock STK STK STK STK STK STK STK STK STK STK STK STK STK STK STK N.S. N.S. N.S. STK

used on

JD: 190E, 290D, Competitive: Backhoes, Clamshells, Draglines, Excavators, Face Shovels, Loaders, Scrapers, Shovel Dippers

Esco Conical - Teeth by Series 30 Series Conical style a c b d -

description sharp tiger twin tiger flare, 6" std pin std retainer ratchet pin ratchet retainer adapter adapter adapter tooth, tilt front adpt., W-O, bttm. leg, 1.25" to 1.5" lip adpt., W-O, bttm. leg, 1.5" lip adpt. nose, W-O

part no. T30S T30VIP T30TVIP T30S6F T2530PN T2530LK T2530PNR T2530LKR PM3807-30 TH108948 TH103467 PM30THX PM838-30HX PM855-30HX PMEWN30

rcv. disc. 9 9 9 9 9 9 9 9 9 9 9

non stock STK STK STK STK STK STK STK STK STK STK STK STK STK STK N.S.

part no. T35S T35VIPA T35TVIPA T35S6F PM3808-35 T35PN T3540LK T35PNR T3540LKR EX119-35 EX20SP EX20W2 EX20W3 EX20W1 PM136-35HX PMP136 PM822-35HX PM839-35HX PM1899-35HX PM1875-35HX PMEWN35

rcv. disc. 9 9 9 9 9 9 9 9 9 9 9 9 9 9

non stock STK STK STK STK STK STK STK STK STK STK STK STK STK STK N.S. STK N.S. N.S. STK STK N.S.

part no. T40S T40VIPA T40TVIP T40S7F PM3809-40 TH111281 TH109817 TH102450 T40PN T3540LK T40PNR T3540LKR PM236-40HX PM129-40HX PMP236 PMEWN40

rcv. disc. 9 9 9 9 9 9 9 9 9 9 9 9

non stock STK STK STK STK STK STK STK STK STK STK STK STK N.S. STK STK STK

used on

JD: 490, 490D, 490E, 495D, 590D, 595, 595D, Competitive: Clamshells, Draglines, Excavators, Face Shovels, Loaders, Scrapers, Shovel Dippers

35 Series Conical style a c b d -

description sharp tiger twin tiger flare, 6" adapter std pin std retainer ratchet pin ratchet retainer adapter spool wedge wedge wedge adpt., stake-type, for C-19 Hensley flex pin for C-19 Hensley lips (136-35HX) adpt., W-O, bttm. leg, 1.5" lip adpt., W-O, bttm. leg, 1.5" to 1.75" lip adpt., W-O, 1-1/2 leg, 1.5" lip adpt., W-O, 1-1/2 leg, 1.25" lip adpt., nose, W-O

used on

JD: 690, 690A, 690B, 690C, 690D, 690E, Competitive: Clamshells, Draglines, Excavators, Face Shovels, Loaders, Scrapers, Shovel Dippers

40 Series Conical style a c b d -

description sharp tiger twin tiger flare adapter adapter adapter adapter std pin std retainer ratchet pin ratchet retainer adpt., stake-type, for Hensely lips adpt., stake-type, for C-29 ESCO lips flex pin for C-29 Hensley lips (236-40) adpt., nose, W-O

used on

JD: 790, 790D, 790E, 792, 792D, Competitive: Clamshells, Draglines, Excavators, Face Shovels, Loaders, Scrapers, Shovel Dippers

Esco Conical - Teeth by Series 45 Series Conical style a c b d

-

description sharp tiger twin tiger flare, 8" tooth, long tooth, rock chisel adapter std pin std retainer ratchet pin ratchet retainer adpt., stake-type, ESCO C-29 lip spool wedge wedge wedge adpt., stake-type, ESCO C-29 lip flex pin for C-29 ESCO lips (236-40) adpt., stake-type, Hensley C-29 flex pin for C-29 Hensley lips (236-40) adpt., W-O bttm. leg adpt., W-O 1-1/2 leg 2" lip adpt., nose, W-O

part no. T45S T45VIPA T45TVIP T45S8F PM45LPHX PM45RDXHX AT131709 T45PN T45LK T45PNR T45LKR EX129-45 EX29SP EX29W1 EX29W2 EX29W3 PM129-45HX PMP236 PM236-45HX PMP236 PM840-45HX PM2810-45HX PMEWN45

rcv. disc. 9 9 9 9

part no. PM50SHX PM50SLHX PM50VIPHX PM50TVIPHX PM50RHX PM50RDXHX PM50APHX PM50S9FHX PM50LPHX PM50PNP PM50LKR PM50PNRP PM50LKRR PM3811-50HX PMEWN50

rcv. disc.

non stock STK N.S. STK N.S. N.S. STK N.S. N.S. N.S. STK STK STK STK N.S. N.S.

used on

description part no. sharp PME55HX sharp short PM55SSHX sharp long PM55LPHX tiger PM55VIPHX twin tiger PM55TVIPHX rock PM55RHX rock chisel PM55RDXHX abrasion panel PM55APHX flare, 10" PM55S10FHX slag PM55AHX heavy slag PM55AHHX panel sharp PM55SPHX pin PM55PNP ratchet pin PM55PNRP wedge pin PM55PNTP rubber lock PM55LKR ratchet rub lock PM55LKRR adpt., W-O, 1-1/2 leg, 3 straight lip, 23 degre PM1856-55HX adpt., nose, W-O PMEWN55

rcv. disc.

non stock N.S. N.S. STK N.S. N.S. STK STK N.S. N.S. N.S. N.S. N.S. STK STK STK STK STK N.S. N.S.

used on

9 9 9 9 9 9 9 9 9 9

non stock STK STK STK STK N.S. STK STK STK STK STK STK STK STK STK STK STK STK STK N.S. STK N.S. STK N.S.

used on

JD: 890, 890A, 892D, 892E, 992D, 992E, Competitive: Clamshells, Draglines, Excavators, Face Shovels, Loaders, Scrapers, Shovel Dippers

50 Series Conical style a a c b

-

description sharp long sharp tiger twin tiger rock rock chisel abrasion panel flare, 9" long pin rubber lock ratchet pin ratchet rub lock adpt., W-O, 1-1/2 leg, 2.25 lip, 30 degrees adpt., nose, W-O

55 Series Conical style a a a c b

d

-

Esco Conical - Teeth by Series Early "R" Series Conical style

description tooth pin rubber plug adpt., W-O, bttm. leg, 1.25" lip

part no. PMR2HX PMR2P PMR2R PMCB11255R2H

rcv. disc.

non stock STK STK STK STK

used on Competiitive: Clamshells, Draglines, Excavators, Face Shovels, Loaders, Scrapers, Shovel Dippers

Esco Super Conical- Applications 36 Series Super Conical style description flared panel tilt front c tiger lock pin

part no. PM36FPHX PM36THX PM36VIPHX PM36LKR PM36PNP

rcv. disc.

part no. PM46ARLHX PM46RHX PM46FPHX PM46THX PM46VIPHX PM46LKR PM46PNP

rcv. disc.

part no. PM56ARLHX PM56FPHX PM56RHX PM56VIPHX PM56LKR PM56PNP

rcv. disc.

part no. PMT1154CHX PMT1155CHX PMT2143AHX PMT2144AHX PMT1156AHX PMT1157AHX PMPDE31329HX

rcv. disc.

non stock STK N.S. N.S. STK STK


46 Series Super Conical style description long rock rock flared panel tilt front c tiger lock pin

non stock N.S. STK STK N.S. N.S. STK STK

used on

Competiitive: Clamshells, Draglines, Excavators, Face Shovels, Loaders, Scrapers, Shovel Dippers

56 Series Super Conical style description long rock d flared panel rock c tiger lock pin

non stock N.S. N.S. N.S. N.S. STK STK


Sidecutters style description sidecutter, LH, 4" add'1 sidecutter, RH, 4" add'1 sidecutter, LH, 2" add'1 sidecutter, RH, 2" add'1 sidecutter, LH, 6" add'1 sidecutter, RH, 6" add'1 sidecutter, strikeoff

non stock STK STK N.S. STK STK STK STK

used on


Esco Ripper Teeth- Applications 22 Series style description tooth, ripper bushing pin

part no. PM22R10HX PM22RBGB PM22RPGP

rcv. disc.

part no. PM25R11HX PM25R12HX PM25RNHX EX25R12

rcv. disc.

non stock STK STK STK


25 Series style description tooth, ripper tooth, ripper ripper, nose, W-O tooth, ripper

non stock STK STK STK STK


Esco Conical - Teeth by Series 35 Series style description ripper tooth tooth, ripper 14 tooth, ripper 15 tooth, ripper 15 tooth, ripper, tiger, 15 tooth, ripper, twin tiger, 14 bushing, rubber bushing, slag pin, solid

part no. T35-5R15 PM35R14HX PM35R15HX PM35R15AHX PMT35R15 PM35RWTHX PM35RB PM35RBS PM35RP

rcv. disc. 9

part no. PM39-5R17AHX PM39RP

rcv. disc.

non stock STK STK STK STK N.S. N.S. STK STK STK

used on


39 Series style description tooth, ripper pin bushing

PM39RB

non stock STK STK STK


Esco Conical - Specifications

T Type 4

18 Series Conical style T T T T T 4

description long sharp tilt front tiger twin tiger adapter tooth, long pin rubber lock tooth, ripper adpt., W-O, bttm. Leg, 1.25" lip adpt., B-O, 1-1/2 leg, (Case W18, W20) adpt., B-O, 2 leg, (Case 850B) adpt., B-O, crnr., RH (Case 850) adpt., B-O, crnr., LH (Case 850) adpt., B-O, 1-1/2 leg, 1.06" thr

part no. PM18TL PM18SLHX PM18THX PM18VIPHX PM18TVIPHX PM833-18 PM18LPHX PM18-20MPNP PM18-20MLKR PM22R10HX PM855-18HX PM4718-18HX PM4729-18HX PM5701R-18HX PM5701L-18HX PM5707-18HX

a 4-11/16" 5-7/8" 4-13/16" 6-7/8" 6-7/8" -

b 2-1/8" 2-1/8" 2-3/16" 3/8" 3" 3/4"

c 1-13/16" 1-13/16" 1-13/16" 1-13/16" 1-13/16" 3-7/8"

d 1-1/2" 1-1/2" 1-1/2" 1-1/2" 1-1/2" 23°

lbs. 3.1 1.9 1.8 2.5 3 3.3 2.1 0.1 0.1 8 4.2 6.6 8.5 12 12 6.5

part no. T25S T25VIP T25TVIP T25S5F PM25TF PM855-25 PM3806-25 PM25THX PM4703-25HX PM5710L-25HX PM5710R-25HX PMEWN25

a 6-5/8" 8-1/8" 8" 6-1/2" 6-5/16" -

b 2-1/2" 1/8" 3-1/4" 4-7/8" 3-5/16" 1" -

c 2-1/2" 2-1/2" 2-1/2" 2-1/2" 2-1/2" 5-1/4" -

d 2-1/8" 2-1/8" 2-1/8" 2-1/8" 2-1/8" 23° 20°

11/16"

3-1/16"

2-7/8"

-

lbs. 5.6 6.9 7.4 7.4 6.0 7.3 10.5 4.8 12.5 12.8 12.5 4.9

25 Series Conical style T T T T T 4 2

description sharp tiger twin tiger flare, 5" d-p flare adapter adapter tooth, tilt front adpt., B-O, 1-1/2 leg, (Case 1150) adpt., B-O, crnr., LH adpt., B-O, crnr., RH nose, W-O

Esco Conical - Specifications 30 Series Conical style T T T T 2 1 1

description sharp tiger twin tiger flare, 6" adapter adapter adapter tooth, tilt front adpt., W-O, bttm. leg, 1.25" to 1.5" lip adpt., W-O, bttm. leg, 1.5" lip nose, W-O

part no. T30S T30VIP T30TVIP T30S6F PM3807-30 TH108948 TH103467 PM 30THX PM 838-30HX PM 855-30HX PMEWN30

a 6-1/2" 8-1/4" 8-1/4" 6-5/8" 6-1/2" 3-1/2" 4-14"

b 3-1/8" 1/8" 3-3/4" 6" 1-1/4" 1-5/16" 1-5/16"

c 3" 3" 3" 3" 6" 8" 9-7/8"

d 2-1/4" 2-1/4" 2-1/4" 2-1/4" 23° 25° 15°

3/4"

3-1/8"

3-3/8"

-

part no. T35S T35VIP T35TVIPA T35S6F PM3808-35 EX119-35 PM136-35HX PM822-35HX PM839-35HX PM1899-35HX PM1875-35HX PMEWN35

a 7-3/4" 10/7/2016 10" 7-3/4" 6-1/4" 6-1/4"

b 3-5/8" 1/8" 4-1/4" 6" 1-5/8" 1-5/8"

c 3-1/2" 3-1/2" 3-1/2" 3-1/2" 5-3/4" 6-1/4"

d 2-5/8" 2-5/8" 2-5/8" 2-5/8" 23° 13°

3/4"

3-5/8"

4"

-

part no. T40S T40VIPA T40TVIP T40S7F PM3809-40 TH111281 TH109817 TH102450 PM236-40HX PM129-40HX PMEWN40

a 9" 12-5/16" 10" 8-3/4" 7-1/2" 4" 4" 6-1/4"

b 4-1/4" 1/4" 4-3/4" 6-5/8" 1-5/8" 1-5/8" 1-1/2" 1-5/8"

c 4" 4" 4" 4" 7" 8-3/4" 8-3/4" 10-3/4"

d 3" 3" 3" 3" 23° 17° 18° 43°

1"

4-1/4"

4-1/2"

-

lbs. 6.6 7.2 9.3 8.5 17.0 13.9 17.5 6.0 11.1 9.2 5.6

35 Series Conical style T T T T 2 3

description sharp tiger twin tiger flare, 6" adapter adapter adpt., stake-type, for C-19 Hensley adpt., W-O, bttm. leg, 1.5" lip adpt., W-O, bttm. leg, 1.5" to 1.75" lip adpt., W-O, 1-1/2 leg, 1.5" lip adpt., W-O, 1-1/2 leg, 1.25" lip nose, W-O

lbs. 10.6 6.9 11.2 11.7 19.4 17.1 19.4 25.0 22.1 22.6 20.6 9.4

40 Series Conical style T T T T 2 1 1 1

description sharp tiger twin tiger flare adapter adapter adapter adapter adpt., stake-type, for Hensley adpt., stake-type, for C-29 ESCO lips nose, W-O

lbs. 14.5 15.4 16.6 15.1 33.1 26.0 27.2 28.4 43.8 27.0 13.7

Esco Conical - Specifications 45 Series Conical style T T T T

2 3

description sharp tiger twin tiger flare, 8" tooth, long tooth, rock chisel adapter adpt., stake-type, ESCO C-29 lip adpt., stake-type, ESCO C-29 lip adpt., stake-type, Hensley C-29 adpt., W-O bttm. leg adpt., W-O 1-1/2 leg 2" lip nose, W-O

part no. T45S T45VIPA T45TVIP T40S8F PM45LPHX PM45RDXHX AT131709 EX129-45 PM129-45HX PM236-45HX PM840-45HX PM2810-45HX PMEWN45

a 10" 13-3/4 11" 9-7/8"

b 4-5/8" 1/4" 5-1/2" 7-3/4"

c 4-1/2" 4-1/2" 4-1/2" 4-1/2"

d 3-1/4" 3-1/4" 3-1/4" 3-1/4"

7-1/4" 9"

2-1/4" 2-1/2"

7-1/4" 9"

25° 17°

1-1/16"

4-1/2"

5"

-

c 4-7/8" 4-7/8" 4-7/8" 4-7/8" 4-7/8" 4-7/8" 4-7/8" 4-7/8" 4-7/8"

d 3-13/16" 3-13/16" 3-13/16" 3-13/16" 3-13/16" 3-13/16" 3-13/16" 3-13/16" 3-13/16"

lbs. 20.8 22.9 24.8 25.2 16.4 17.7 44.0 33.3 32.7 48.5 35.1 45.2 17.9

50 Series Conical style T T T T T T T T T

description sharp long sharp tiger twin tiger rock rock chisel abrasion panel flare, 9" long adpt., W-O, 1-1/2 leg, 2.25 lip, 30 degrees nose, W-O

part no. PM50SHX PM50SLHX PM50VIPHX PM50TVIPHX PM50RHX PM50RDXHX PM50APHX PM50S9FHX PM50LPHX PM3811-50HX PMEWN50

a b 11-1/8" 5-11/16" 11-1/8" 5-1/4" 15" 5/8" 13" 6-1/2" 10-5/8" 5-1/4" 12" 3" 11-3/4" 5-3/4" 11" 9" 11-15/16" 5-1/8" 1-3/8"

5-5/16"

5-1/16"

-

a

b

c

d

10-5/16" 13-1/4" 16-1/2" 15-1/2" 11-1/8" 13-1/2" 12-3/4" 11-1/4" 11-3/8" 12-3/16" 12"

6" 6" 3/4" 7" 6" 3-3/8" 6-1/2" 10" 6" 6" 5-1/2"

5-3/8" 5-3/8" 5-3/8" 5-3/8" 5-3/8" 5-3/8" 5-3/8" 5-3/8" 5-3/8" 5-3/8" 5-3/8"

4-1/4" 4-1/4" 4-1/4" 4-1/4" 4-1/4" 4-1/4" 4-1/4" 4-1/4" 4-1/4" 4-1/4" 4-1/4"

lbs. 22.4 23.0 31.6 34.8 23.7 20.3 30.9 28.8 26.9 60.4 23.7

55 Series Conical style T T T T T T T T T T T

description tooth, std. sharp short sharp long tiger twin tiger rock rock chisel abrasion panel flare, 10" abrasion heavy slag panel sharp adpt., W-O, 1-1/2 leg, 3 straight lip, 23 degrees nose, W-O

part no. PME55HX PM55SSHX PM55LPHX PM55VIPHX PM55TVIPHX PM55RHX PM55RDXHX PM55APHX PM55S10FHX PM55AHX PM55AHHX PM55SPHX PM1856-55HX PMEWN55

lbs. 27.4 25.9 36.1 43.1 51.2 31.5 31.9 39.0 35.0 34.6 44.6 31.5 81.0 31.2

Esco Conical - Specifications Early "R" Series Conical style

description tooth rubber plug Adpt., W-O, bttm. leg, 1.25" lip

part no. PMR2HX PMR2R PMCB11255R2H

a

b

c

d

lbs. 3.0 0.1 5.5

a 8-3/4" 8" 10"

b 3-3/4" 4" 7/16"

c 2-5/16" 2-5/16" 2-5/16"

d 2-3/8" 2-3/8" 2-3/8"

lbs. 7.8 8.6 8.1

Esco Super Conical - Specifications 36 Series Super Conical style T flared panel T tilt front T tiger

description

part no. PM36FPHX PM36THX PM36VIPHX

46 Series Super Conical style T T T T T

description long rock rock flared panel tilt front tiger

part no. PM45ARLHX PM46RHX PM46FPHX PM46THX PM46VIPHX

a

b

c

d

lbs.

11-7/8" 10-1/8"

5" 3-3/4"

2-3/4" 2-3/4"

3-3/16" 3-3/16"

10-1/2" 12-7/8"

4-1/4" 5/8"

2-3/4" 2-3/4"

3-3/16" 3-3/16"

25.7 16.7 17.8 17.8 17.4

a

b

c

d

lbs.

14-1/2" 14" 12-3/4" 15-1/2"

6-1/4" 5-1/2" 4-1/2" 5/8"

3-3/8" 3-3/8" 3-3/8" 3-3/8"

4-3/16" 4-3/16" 4-3/16" 4-3/16"

49.5 36.0 31.4 36.2

a

b

c

d

lbs. 53.5 54.8 43.6 44.4 59.0 59.5 37.0 4.9

56 Series Super Conical style T T T T

description long rock flared panel rock tiger

part no. PM56ARLHX PM56FPHX PM56RHX PM56VIPHX

Sidecutters style

description sidecutter, LH, 4" add"1 sidecutter, RH, 4" add"1 sidecutter, LH, 2" add"1 sidecutter, RH, 2" add"1 sidecutter, LH, 6" add"1 sidecutter, RH, 6" add"1 sidecutter, strikeoff adpt. nose, W-O

part no. PMT1154CHX PMT1155CHX PMT2143AHX PMT2144AHX PMT1156AHX PMT1157AHX PMPDE31329HX PMEWN25

Esco Conical - Specifications Esco Ripper Teeth- Specifications 22 Series style

description

part no. PM22R10HX

a

b

c

d

lbs. 8.0

description

part no. PM25R11HX PM 25R12HX PM 25RNHX

a

b

c

d

lbs. 11.0 13.1 18.1

description tooth, ripper 14 tooth, ripper 15 tooth, ripper 15 tooth, ripper, tiger, 15 tooth, ripper, twin tiger, 14 ripper tooth

part no. PM35R14HX PM35R15HX PM35R15AHX PMT35R15 PM35RWTHX T35-5R15

a

b

c

d

lbs. 26.0 27.1 29.0 30.0 31.8 30.4

part no. PM39-5R17AHX

a

b

c

d

lbs. 43.6

tooth, ripper

25 Series style tooth, ripper tooth, ripper ripper, nose, W-O

35 Series style

39 Series style

description tooth, ripper

Replacements for Esco Conical Products

Retainers

Illustrated parts are actual size.

PM18LK - 18 Series

T2530LKR - 25 and 30 Series

T2530LK - 25 and 30 Series

T3540LKR - 35 and 40 Series

T3540LK - 35 and 40 Series

T45LKR - 45 Series

T45LK - 45 Series


Esco Conical 13

Replacements for Esco Conical Products



T2530PN 25 and 30 Series T45PN 45 Series T45PNR

T40PN 40 Series T40PNR

T35PN 35 Series T35PNR T2530PNR 25 and 30 Series

PM18PN 18 Series


Esco Conical 14

Esco Helilok®/Vertalok® Systems

Style a

Style b

Style c

Standard Teeth (SYL Suffix) (Centerline)

Tiger Teeth (VIP Suffix) (Non-Centerline)

Twin Tiger Teeth (TVIP Suffix) (Non-Centerline)

•

•

•

•

For general-purpose to heavyduty digging and loading Excellent penetration and wear

Style d

High penetration for frost and tough material

Style e

Flare Teeth (S_F Suffix) (Centerline)

Chisel Teeth (SD Suffix) (Centerline)

•

• • •

•

•

For digging and loading in extremely tight material Use as a corner tooth with tiger teeth in the center

For digging in mud-like conditions Wide bite for trench cleanup

Chisel shape with sharp profile Excellent penetration Greater wear than tiger or twin tiger teeth

Part Number Explanation for Esco Helilok®/Vertalok® Teeth Prefix

Suffix

Explanation

EX EX EX EX EX EX

ARL SD S_F SYL VIP TVIP

Abrasion Chisel Flare (S5F indicates a sharp edge with a 5" flare) Standard Tiger Twin Tiger

Esco Helilok® Vertalok® System Helilok/Vertalok teeth are designed to give you up to 20% more wear material up-front over other tooth systems. As a result, more time can be spent digging and loading rather than replacing teeth.

Teeth mount on both the Vertalok and Helilok adapters with a quarter turn and butt up against the adapter nose to take thrust loads head-on. The helical threads and large stabilizing flats at the end of the nose deliver maximum resistance to severe breakout forces. Digging forces are distributed over the entire nose surface which results in added strength and durability.

With Quadrilok, the helical threads create a "locknut" force to resist shock loads and keep point securely locked. Loading stresses are distributed over the entire nose for unmatched resistance to breakout and digging forces. Greater strength and load bearing area. Point twists onto the adapter with a quarter turn.

Helilok® Vertalok® Adapters Horn Style

Available for Esco Horn-style lips

1 1/2 (Top Leg)

Extra strength and weld surface for tough digging conditions

Side Cutter

Tooth-type side cutters cut extra clearance

1 1/2 (Bottom) Leg

Fits a wide range of lip thicknesses. Designed for general-purpose use backhoes - excavators

Spherical

Designed for Esco S19 and S29 series bucket lips

Esco Helilok®/Vertalok® Systems ®

Quadrilok

®

Quadrilok

®

(For Helilok

Pin and Plug (For Vertalok® Adapters)

Adapters)

®

Retainer for Helilok

Retainers

Pin and Plug for Vertalok® Adapters

Adapters

Teeth are held on to Helilok® adapters by a driveon, one-piece Quadrilok® retaining system. With the Quadrilok, the helical threads create a lock-nut force that tightens under load and resists rotation under the most severe impact. The U-shaped Quadrilok eliminates the need for snap rings or rubber-bonded locks, and it prevents the tooth from rotating.

Teeth are securely fastened to Vertalok adapters with a drive-through pin which provides maximum holding power and virtually eliminates tooth loss. The pin is held in place by a spring-loaded plug that fits snugly into a cavity in the side of the adapter nose. Both the pin and the plug are reusable provided they are not damaged. Pins can be removed with a pin or punch.

Special Tools for Quadrilok® Adapters For removal and installation of the 21 and 27 Series Teeth, use special tool EX21-27QRT. For the 37, 47, and 57 Series, use special tool EX3-4-57QRT. Special tools for Vertalok® Adapters For removal and installation of 37, 47 and 57 series Vertalok teeth, use special tool EXPRT Spool and Wedge Adapter Locks for Horn Style Adapters: Install a spool in front of the key slot and a wedge in the rear of the key slot. Oversize wedges are available to compensate for wear. Use a standard wedge (W1) when installing a new adapter on a new or reconditioned lip. When the W1 is nearly flush with the top of the lip, replace it with a W2 wedge. When the W2 wedge drives flush, replace it with a W3 wedge. To avoid lip damage, rebuild the adapter promptly when a W3 drives flush with the top of the lip.

Series 21 or 27 37

Fluted Spool EX20SP EX29SP

W1 EX230W1 EX29W1

Side Wear Shroud (bolt-on)

EX31329-X

A

B

Weight

3.95

5.97

40

Fluted Wedge W2 EX20W2 EX29W2

W3 EX20W3 EX29W3

Esco Helilok® / Vertalok® Products

Retainers

Quadrilok® for Helilok® Adapters Illustrated parts are actual size

EX21LKS 21 Series

EX37LKS 37 Series

EX27LKX 27 Series

Esco Helilok®Vertalok® Products

Retainers

Quadrilok® for Helilok® Adapters; Pins for Vertalok® Adapters Illustrated parts are actual size

EX57LKS 57 Series

EX27VPL 27 Series

EX37VPL 37 Series

EX47VPL 47 Series

EX57VPL 57 Series

Esco Helilok®Vertalok® Products Quadrilok® for Helilok® Adapters

Retainers

Illustrated parts are actual size

EX47LKS 47 Series

EX57VPN 57 Series

EX47VPN 47 Series

EX37VPN 37 Series

EX27VPN 27 Series

ESCO Helilok®/Vertalok® - Specifications

T

7

17 Series style T

description standard

part no. EX17TL

a 5-1/2"

b 1-7/8"

c 1-1/2"

d 1-3/4"

lb 2.3

part no. EX21SYL EX21VIP EX21TVIP EX21S5F EX119-21 EX360-21 EX1550-21 EX1551-21

a 7-1/2" 7-1/8" 7-1/8" 7-1/2" 1-5/8" 2-1/2" 4-5/8" 4-5/8"

b 3" 1/4" 3-1/4" 5" 5-7/8" 2-3/8" 6" 6"

c 1-5/8" 3-7/8" 3-7/8" 3-7/8"

d 1-1/4" 4-3/4" -

lb 6.7 5.9 7.2 10.4 15.4 15.0 21.8 21.7

21 Series style T T T T 3 7 4 4

description standard tiger twin tiger 5" flare adapter adapter adapter adapter

ESCO Helilok®/Vertalok® - Specifications

Esco Helilok®/Vertalok® - Tooth by Series

17 Series style description a

standard

part no. EX17TL

disc. used on ü

Competitive: backhoes, mini-excavators

21 Series style a c b f -

description standard tiger twin tiger 5" flare Quadrilok adapter adapter adapter adapter adapter adapter

part no. EX21SYL EX21VIP EX21TVIP EX21S5F EX21LKS EX119-21 EX360-21 EX1550-21 EX1551-21 EX5854-21 EX5849-21

disc. used on ü ü ü ü ü JD: 190E, 290D, 490, 490D, 490E, 495D Competitive: backhoes, ü excavators ü ü ü ü ü

27 Series style a c b f d e

description standard tiger twin tiger 6" flare chisel HD Sharp

part no. EX27SYL EX27VIP EX27TVIP EX27S6F EX27SD EX27S

ü ü ü ü ü ü

used on JD: 590D, 595, 595D, 690C, 690D, 690E, 790, 790D, 790E, 792, 792D Competitive: backhoes, excavators Case: 9030; Cat: EL180, EL200B, 215D, EL240B, All B and S family, EL180, EL200B, EL240B, Daewoo: DH130, DH170, DH180, DH200, Dresser: 545, Fiat-Allis: FX150, FX200, Gradall: Tracksta, Hyundai: R130, R200, JCB: 818, 820, Kawasaki: 90ZIII, Kobelco: SK200IV, SJ229IV, Koehring: 6612, 6615, 6620, Komatsu, PC200-6, PC210-6, WA380-1. WA400-1, WA450-

27 Series style -

description Quadrilok adapter adapter adapter adapter adapter pin plug adapter

part no. EX27LKX EX119-27 EX360-27 EX1550-27 EX1551-27 EX5827-27 EX27VPN EX27VPL EX5850-27V

ü ü ü ü ü ü ü ü ü

used on JD: 590D, 595, 595D, 690C, 690D, 690E, 790, 790D, 790E, 792, 792D Competitive: backhoes, excavators Case: 9030; Cat: EL180, EL200B, 215D, EL240B, All B and S family, EL180, EL200B, EL240B, Daewoo: DH130, DH170, DH180, DH200, Dresser: 545, Fiat-Allis: FX150, FX200, Gradall: Tracksta, Hyundai: R130, R200, JCB: 818, 820, Kawasaki: 90ZIII, Kobelco: SK200IV, SJ229IV, Koehring: 6612, 6615, 6620, Komatsu, PC200-6, PC210-6, WA380-1. WA400-1, WA4502, WA500-1, Liebherr: R912, R922, Link-Belt: LS2700Q, LS2800Q, MDI/Yutani: MD200BLC, MD240BLC, MD240LC, O&K Trojan: RH8, RH9, Samsung: SE210, L160, Yutani: MD200C, MD240C

37 Series style a c b f f d e -

-

description standard tiger twin tiger 7' flare 8' flare Chisel HD Sharp Quadrilok

part no. EX37SYL EX37VIP EX37TVIP EX37S7F EX37S8F EX37SD EX37SH EX37LKS

used on ü ü ü ü ü ü ü ü

adapter adapter adapter adapter pin plug adapter

EX450-37 EX5824-37 EX1506-37 EX1507-37 EX37VPN EX37VPL EX5856-37V

ü ü ü ü ü ü ü

JD:690C, 690D, 690E, 790, 790D, 790E, 792, 792D, 892D, 892E, 922D, 922E, Case: 9040, 9050, Caterpillar: 225D, 231D, 980F, 988F, All C , D, E Family, EL300B, Competitive: Excavators, Daewoo: DH220, DH280, DH320, Dresser: 555,560B, Fiat-Allis: FX220, FX300, Hyundai: R280, R290, R320, 95ZIII, 110III, Kobelco: SK300IV, Koehring: 6625, 6627, 6633, Komatsu: PC220-6, PC250-6, PC300-5, Liebherr: R932, R942, Link-Belt: LS3400Q, LS4300Q, MDI/Yutani: MD300LC, MD320BLC, O&K Trojan, RH11, RH12, Samsung: SE280, SE350, VME: L190B, L270B, Yutani: 320BLC

47 Series style a c b f d e -

description standard tiger twin tiger 9' flare chisel HD Sharp Quadrilok adapter adapter pin plug adapter

part no. EX47SYL EX47VIP EX47TVIP EX47TS9F EX47SD EX47SH EX47LKS EX450-47 EX1829A-47 EX47VPN EX47VPL EX5857-47V

used on ü ü ü ü ü ü ü ü ü ü ü ü

JD: 892D, 892E, 992D, 992E, 9060, Caterpillar: 235C, 245B, All F, G Family, EL450, Competitive: Loaders, Daewoo: DH450, Demag: H40, Dresser: 570, Fiat-Allis: FX400, Hyundai: R450, Kawasaki: 115ZIII, Kobelco: SK400IV, SK600IV, Koehring: 6644, Komatsu: PC400-5, WA600-1, Liebherr: R952, R954, R962, Link-Belt: LS5800CII, MDI/Yutani: MD400LC, MD450BLC, O&K Trojan: RH18, RH20, Samsung: SE450,

57 Series style a c b -

description standard tiger twin pin plug Quadrilok adapter

part no. EX57SYL EX57VIP EX57TVIP EX57VPN EX57VPL EX57LKS EX1856A-57V

used on ü ü ü ü ü ü ü

Caterpillar: 245B, 245BLC, 245ME, 922, 922C, Competitive: Loaders, Demag: H55, H65, H85, H121, Kobelco: SK400IVME, Komatsu: PC650-3, WA700-1, WA800-2, Liebherr: R962, R972, R972HD, R974, R981, R982, Link-Belt: LS7400CII, MDI/Ytani: SK400, O&K Trojan: RH30C, RH30D, RH40C, VME: 480, L320, L480

MACHINE APPLICATION FOR HELILOK /VERTALOK SYSTEMS Company

Equipment

Series

Demag

H40-------------------------------------------------------------------------------47 H55, H65, H85, H121---------------------------------------------------------57

Dresser

545 -------------------------------------------------------------------------------27 555, 560B -----------------------------------------------------------------------37 570 -------------------------------------------------------------------------------47

Fiat-Allis

FX150, FX200------------------------------------------------------------------27 FX220, FX300------------------------------------------------------------------37 FX400 ---------------------------------------------------------------------------47

Gradall

Tracksta -------------------------------------------------------------------------27

Hyundai

R130, R200 ---------------------------------------------------------------------27 R280, R290, R320 -------------------------------------------------------------37 R450 -----------------------------------------------------------------------------47

JCB

818, 820 -------------------------------------------------------------------------27

Kawasaki

90ZIII----------------------------------------------------------------------------27 95ZIII, 110ZIII -----------------------------------------------------------------37 115ZIII --------------------------------------------------------------------------47

Kobelco

SK200IV, SK220IV -----------------------------------------------------------27 SK300IV ------------------------------------------------------------------------37 SK400IV ------------------------------------------------------------------------47 SK400IVME--------------------------------------------------------------------57 SK600IV ------------------------------------------------------------------------47

Koehring

6612, 6615, 6620---------------------------------------------------------------27 6625, 6627, 6633---------------------------------------------------------------37 6644------------------------------------------------------------------------------47

Komatsu

PC200-6, PC210-6 -------------------------------------------------------------27 PC220-6, PC250-6, PC300-5-------------------------------------------------37 PC400-5 -------------------------------------------------------------------------47 PC650-3 -------------------------------------------------------------------------57 WA380-1, WA400-1, WA450-2, WA500-1 -------------------------------27 WA600-1------------------------------------------------------------------------47 WA700-1, WA800-2 ----------------------------------------------------------57

Liebherr

R912, R922 ---------------------------------------------------------------------27 R932, R942 ---------------------------------------------------------------------37 R952, R954 ---------------------------------------------------------------------47 R962 -----------------------------------------------------------------------------47 57 R972, R972HD, R974, R981, R982 -----------------------------------------57

MACHINE APPLICATION FOR HELILOK /VERTALOK SYSTEMS Company

Equipment

Series

Link-Belt

LS2700Q, LS2800Q -----------------------------------------------------------27 LS3400Q, LS4300Q -----------------------------------------------------------37 LS5800CII ----------------------------------------------------------------------47 LS7400CII ----------------------------------------------------------------------57

MDI/Yutani

MD200BLC, MD240BLC, MD240LC -------------------------------------27 MD200C, MD240C------------------------------------------------------------27 MD300LC-----------------------------------------------------------------------37 MD320BLC---------------------------------------------------------------------37 MD400LC, MD450BLC ------------------------------------------------------47 SK400 ---------------------------------------------------------------------------57

O&K Trojan

RH8, RH9 -----------------------------------------------------------------------27 RH11, RH12 --------------------------------------------------------------------37 RH18, RH20 --------------------------------------------------------------------47 RH30C, RH30D, RH40C -----------------------------------------------------57

O&K Trojan

RH8, RH9 -----------------------------------------------------------------------27 RH11, RH12 --------------------------------------------------------------------37 RH18, RH20 --------------------------------------------------------------------47 RH30C, RH30D, RH40C -----------------------------------------------------57

Samsung

SE210----------------------------------------------------------------------------27 SE280, SE350 ------------------------------------------------------------------37 SE450----------------------------------------------------------------------------47

VME

L160 -----------------------------------------------------------------------------27 L190B, L270B------------------------------------------------------------------37 L320, L480 ---------------------------------------------------------------------57

21 Series 1 1

adapter adapter

EX5854-21 EX5849-21

3-3/4" 3-3/4"

1" 1-5/16"

4-1/2" 9-1/8"

30° 30°

12.9 14.4

part no. EX27SYL EX27VIP EX27TVIP EX27S6F EX27SD EX119-27 EX119-27V EX360-27 EX1550-27 EX1551-27 EX5827-27 EX5850-27V

a 8" 7-3/4" 7-3/4" 8-3/4" 8" 1-5/8" 1-5/8" 2-1/2" 4-5/8" 4-5/8" 2" 2"

b 3-1/2" 1/4" 3-3/4" 6" 2" 5-13/16" 5-13/16" 2-3/8" 6" 6" 1-1/2" 1-9/16"

c 1-23/32" 1-23/32" 3-7/8" 3-7/8" 3-7/8" 9-7/8" 8-1/16"

d 1-5/16" 1-5/16" 4-3/4" 30° 30°

lb 9.4 8.4 16.9 18.0 10.5 18.2 18.2 17.0 28.8 29.1 27.1 19.0

part no. EX37SYL EX37VIP EX37TVIP EX37S7F EX37S8F EX37SD EX129A-37 EX129A-37V EX450-37 EX5824-37 EX1506-37 EX1507-37 EX5856-37V

a 9-1/2" 9-1/2" 9-1/2" 11" 11" 10-1/4" 2-1/2" 2-1/2" 3-1/8" 3" 4-5/8" 4-5/8" 4-7/8"

b 4-3/4" 1/4" 4-1/2" 7" 8" 2-1/4" 8-19/32" 8-19/32" 3" 2-1/16" 6" 6" 2-1/6"

c 2-1/2" 2-1/2" 5" 9-3/4" 3-7/8" 3-7/8" 9-3/4"

d 1-3/4" 1-3/4" 5-3/4" 30° 30°

lb 17.3 13.9 16.7 25.7 27.0 17.4 37.1 37.1 31.0 30.3 60.2 60.2 37.9

part no. EX47SYL EX47VIP EX47TVIP EX47TVIP EX47SD EX1829A-47 EX450-47 EX5857-47V

a 11" 11" 11" 12-5/8" 10-3/4" 3-1/8" -

b 5" 3/8" 5-1/8" 9" 2-1/2" 2-9/16" 3" 2-5/8"

c 4-3/4" 5" 10-5/8"

d 30° 5-3/4" 30°

lb 24.8 22.7 25.8 34.7 25.9 46.4 37.0 57.0

27 Series style T T T T T 3 3 7 5 5 1 1

description standard tiger twin tiger 6" flare chisel adapter adapter adapter adapter adapter adapter adapter

37 Series style T T T T T T 3 3 7 1 6 6 1

description standard tiger twin tiger 7' flare 8' flare chisel adapter adapter adapter adapter adapter adapter adapter

47 Series style T T T T T 2 7 1

description standard tiger twin tiger 9' flare chisel adapter adapter adapter

ESCO Helilok®/Vertalok® - Specifications 57 Series style T T T 2

description standard tiger twin adapter

part no. EX57SYL EX57VIP EX57TVIP EX1856A-57V

a 13" 13-1/8" 13-1/8" 3-3/16"

b 6" 1/2" 6-3/4" 5-7/8"

c -

d -

11-3/4"

25°

lb 34.0 34.0 40.8 71.0

New Generation of Esco Systems: Super V™ The Super V pin, tooth, and adapter system more closely matches break-out forces while reducing fuel consumption and machine maintenance. Slimmer Profile; Matches Break-Out Forces More Closely

Unique 1-Piece, Vertical Pin

The Super V tooth has a slimmer profile which provides increased penetration. The tooth twists a quarter turn onto the adapter and "butts up" against the adapter nose to match breakout forces more closely.

The unique, 1-piece, vertical, drive-thru pin locks to the tooth ear for excellent point retention. It is completely covered by the tooth ear to reduce wear and avoid pin walk. The 1-piece pin provides easier changeover and less cost; it is reusable for 29 Series sizes and larger.

Part Number Explanation Various information can be determined from the part numbering system. Refer to the following chart for basic part number information. Part Number Explanations for Exco Super V™ Prefix Suffix Explanation EV S_F Flare (_indicates width of flare.) Note: The numbers EV SYL Standard Within the part number EV TVY Twin Tiger represent the "Series." EV VY Tiger Examples: EV19SYL 19 Series Standard Tooth EV51TVY 51 Series Twin Tiger Tooth EV43S9F 43 Series 9" Flare Tooth Special tools for Super V Adapters For removal and installation of 29, 33, 39, 43 and 51 Series Super V teeth use special tool EXPRT

New Generation of Esco Systems: Super V™

Standard Teeth (SYL Suffix) (Centerline) • For general-purpose-to-heavy-duty digging conditions. • Excellent penetration and wear.

Tiger Teeth (VY Suffix) (Non-Centerline) • High penetration for frost and tough material.

Twin Tiger Teeth (TVY Suffix) (Non-Centerline) • For digging and loading in extremely tight material. • Use as a corner tooth with tiger teeth in the center.

Flare Teeth (S_F Suffix) (Centerline) • For digging in mud-like conditions • Provides more bucket capacity by bridging material between teeth.

Esco Super V™ Systems

Retainers

Illustrated parts are actual size. EV19PN 19 Series

EV23PN 23 Series

EV29PN 29 Series

EV33PN 33 Series

EV39PN 39 Series

EV43PN 43 Series

EV51PN 51 Series

Esco Super V™ System - Tooth by Series

19 Series style a b c d -

description standard tiger twin tiger flare pin adapter

part no. EV19SYL EV19VY EV19TVY EV19TF EV19PN EV5854-V19

disc. ü ü ü ü ü ü

used on JD: 190E, 290D Competitive: Case: 488C, 590SL Caterpillar: 438B Komatsu: PC95, PC100-5 Liebherr: R310B, O&K: MH2.10



part no. EV23SYL EV23VY EV23TVY EV23S5F EV23PN EV5849-V23

used on ü ü ü ü ü ü

JD: 490, 490D, 490E, 495D, 590D, 595, 595D Competitive: Case: 688C: Caterpillar: 205B, 211B, E110B, E120B Kobelco: SK100, SK120, SL150 Komatsu: PC120-6, PC150LC5 Liebherr: R900Lit; Link-Belt: 2650, 2700





JD: 690, 690A, 690B, 690C, 690D, 690E, Competitive: Case: 883C, 9030, Caterpillar: 215D, 320L, E200B, Kobelco: SK200, Komatsu: PC180LC5, PC200LC6, Liebherr: R902Lit, R912Lit, O&K: RH CITY, RH5





JD: 790, 790D, 790E, 792, 792D, Competitive: Case: 1088C, 1188C, 9040, Caterpillar: 225D, 325L, E240B, E300B, Kobelco: SK220, Komatsu PC220LC6, Liebherr: R922Lit, R923Lit, LinkBelt:: 3400, O&K: RH6-20





JD: 892D, 892E, Competitive: Case: 1288C, 9050, Caterpillar: 235B, 235C, 330L, Kobelco: SK300, Komatsu PC300LC5, PC360LC3, Liebherr: R942Lit, Link-Belt: 4300, O&K: RH12





JD: 922D, 992E, Competitive: Case: 9060, Caterpillar: 235D, 350L, Kobelco: SK400, Komatsu: PC400LC5, Liebherr: R954Lit, Link-Belt: 5800, O&K: RH16, RH20

51 Series style a b c -

description standard tiger twin tiger pin adapter

part no. EV51SYL EV51VY EV51TVY EV51PN EV5857A-V51

used on ü ü ü ü ü

JD: 922D, 992E, Competitive: Caterpillar: 245D, Komatsu: PC650LC3, Liebherr: R964Lit, O&K: RH25

Esco Super V™ System - Specifications

T

19 Series style T T T T 1

description standard tiger twin tiger flare adapter

part no. EV19SYL EV19VY EV19TVY EV19TF EV5854-V19

a 6-1/2" 7" 7" 6-1/2" 1"

b 2-1/2" 7/16" 3" 4-1/2" 3-1/8"

c 6-1/2"

d 30°

nose angle 12°

lbs. 5.2 4.3 5.5 6 8.7

part no. EV23SYL EV23VY EV23TVY EV23S5F EV5849-V23

a 7-1/2" 8" 8" 7-1/2" 1-1/8"

b 3" 1/2" 3-1/2" 5" 3-3/4"

c 7-1/2"

d 30°

nose angle lbs. 6.8 6.5 7.5 8.8 12° 14.5


a 8-5/16" 9-9/16" 9-9/16" 9-1/6" 1-1/2"

b 3-1/2" 7/16" 4-1/8" 6" 4-1/2"

c 8-1/4"

d 30°

nose angle lbs. 10.7 8.7 9.6 13.7 10° 17.5





Esco Super V™ System - Specifications

33 Series style T T T

description standard tiger twin tiger

T flare 1 adapter

part no. EV33SYL EV33VY EV33TVY

a 9-1/8" 10-3/8" 10-3/8"

b 4" 1/2" 4-9/16"

c -

d -

nose angle lbs. 15 12.3 14.2

EV33S7F EV5855-V33

10" 1-1'2"

7" 5"

9-1/4"

30°


a 10-1/8" 11-11/16" 11-11/16" 11" 2"

b c 4-3/4" 9/16" 5-1/8" 8" 5-3/4" 10-3/8"

d 30°

nose angle lbs. 21.5 17.5 19.9 23.3 36 10°


a 11-1/4" 12-7/8" 12-7/8" 12-5/16" 2"

b 5" 5/8" 5-5/8" 9" 6"

d 30°

nose angle lbs. 29 23.5 27.4 38.5 10° 48

part no. EV51SYL EV51VY EV51TVY EV5857A-V51

a 12-1/8" 14" 14" 2-1/2"

b c 5-1/2" 3/4" 6-1/4" 6-7/16" 11-7/8"

d 30°

nose angle lbs. 33 30 36 10° 63

10°

19.6 25





c 11"

51 Series style T T T 1

description standard tiger twin tiger adapter

John Deere Replacement Teeth for Hensley Products John Deere replacement teeth for Hensley products come in sizes and tooth designs to fit almost all machine makes and models. The Parabolic (Dished-Out) Design Creates a Wedging, Self-Tightening Fit With use, the parabolic (dished-out) design mating system creates a wedging and selftightening fit. A dished-out area in the lower top and bottom of the adapter nose plus a recessed channel on the inside sidewall of the tooth which matches a tapered extension on the adapter nose piece forms a locking fit in all directions and reduces tooth movement both vertically and horizontally. The tooth and adapter are designed as a bucket tooth system that will absorb impact loads and generally reduce the amount of abrasive action to the bucket lip. Flex Pin Retention The TP400HD and TP475HD Flex Pins are made of two hardened steel forgings with vulcanized neoprene between them. Once installed, the flex pin provides a four-way locking support. Removal is easy as pins can be driven through the bottom of the adapter. Hensley Series 350, 400 and 475 teeth use a vertically-mounted flex pin. Roll Pin Retention and Installation The smaller series of John Deere replacement teeth for Hensley products are retained with a roll pin. The vertical design allows easy removal and installation of center teeth. It is a simple, economical, reliable means to retain the tooth to the adapter. These steel roll pins should always be installed with the split facing towards the front of the tooth. Series 156, 160, 220, and 310 use a roll pin. Steel Key A steel key retains the 290, 330, 370 and 410 Series of John Deere replacement teeth for Hensley products. This key provides outstanding retention in all types of applications. It is not reuseable.

CE98- 01U,02C Date

Part Number Explanation Various information can be determined from the part number system. Refer to the following chart for basic part numbering information. Part Number Explanation (Replacement Teeth for Hensley Products) Prefix Suffix Explanation TF Fanggs Digging TT Tiger TX Standard TX AP Abrasion Paneled TX F Flare TX WT Twin Tiger Example: Part Number TX400 Series 400 standard tooth. Part Number TX400AP Series 400 abrasion paneled tooth.

NOTE: The numbers within the part number represent the “Series.”

John Deere Replacement Teeth for Hensley Products - Types Available

Fanggs Digging Teeth (TF__) (Non-Centerline) • For general-purpose-to-heavy digging. • Provides a clean start and close crowd.

Abrasion Paneled Teeth (TX__AP) (Centerline) • For loading and digging in highly-abrasive material. • Panel design makes tooth selfsharpening.

Flare Teeth (TX__F) (Centerline) • For digging in loose and mudlike conditions to improve the bridging of material between teeth. • Provides flush cut or clean-up.

Standard Teeth (TX__) (Centerline) • For general-purpose to heavyduty applications. • Provides long wear life.

Tiger Teeth (TT__) (Non-Centerline) • For digging and loading in severe conditions - frost, hardpan, extremely tight soil. • Excellent penetration.

Twin Tiger Teeth (TW__WT) (Non-Centerline) • For digging and loading in extremely tight material. • Use as a corner tooth with tiger teeth in center positions.


Hensley 2

Hensley - Teeth by Series

156 Series (Top Mount) style e f c d b d -

description

part no.

Fanggs TF156 standard TX156 tiger TT156 twin tiger TX156WT tooth, star PMS156 heavy-duty PMS156HD tiger h-d PMT156HD flare PMX156F heavy PMX156H extra long PMX156LP tooth, long PMX156L tooth, twin tiger long PMX156WTL pin TF13P pin TP156 adapter T834X156 adpt., ctr. (156 nose) PM110HX adpt., RH (156 nose) PM110RH adpt., LH (156 nose) PM110LH blade (156 nose) PM11V16L blade (156 nose) PM11V16R adpt., W-O, 1-1/2 leg, .625" lip 30 degrees PM230X156 adpt., B-O, .81" thr., 29deg JCB 3C PM300X156 adpt., B-O, LH, crnr., refer to 300X156 PM301X156 adpt., B-O, RH, crnr. refer to 300X156 PM302X156 adpt., B-O, Deere no. U-41344 PM344X156 adpt., B-O, 1-1/2 leg, .93" throat PM350X156 adpt., B-O, 2 leg, step, Case #D35642 PM401X156 adpt., W-O, 1-1/2 leg, .625" lip PM548X156 adpt., W-O, 1-1/2 leg, .875" lip PM549X156 adpt., W-O, 1-1/2 leg, 1" lip PM550X156 adpt., B-O, .625" throat, 21deg PM551X156 adpt., W-O, 1-1/2 leg, .75"" lip PM552X156 adpt., W-O, flush, .75"" to .875" PM681X156 adpt., B-O, step (Drott TD-6) PM682X156 adpt., B-O, 2 leg, 1.18" throat PM683X156 adpt., B-O, 2 leg, .81" throat PM684X156 adpt., W-O, bttm. leg, 1" lip PM805X156 adpt., W-O, bttm. leg, .625" to .875", ditch wit PM835X156 adpt., W-O, bttm. leg, .75"" to 1.0" lip PM836X156 12" lip blade w/3 noses PM12M156-12A 14" lip blade w/3 noses PM14M156-12A 18" lip blade w/4 noses PM18M156-12A 24" lip blade w/5 noses PM24M156-12A ripper box PMB922B box pin (B922B) PMP922 pin removal tool for P100, P156 PMPRT156 pin punch PM516PU adapter, nose, W-O PM156WN

rcv. disc.

non stock

9 9 9 9

STK STK STK STK STK STK STK STK STK STK STK STK STK STK STK STK STK STK STK STK STK N.S. N.S. N.S. N.S. N.S. N.S. N.S. STK STK N.S. STK STK N.S. N.S. N.S. STK STK STK STK STK STK STK STK STK STK STK STK

9 9 9

used on

JD: 300, 310D, 315D, 410D, 500B, 510, 510D, 710B, Competitive: backhoes

Hensley - Teeth by Series 160 Series (Top Mount) style e f c d b -

Fanggs

description

part no. TF160

standard tiger twin tiger flare star heavy-duty pin adapter adapter adapter adpt., B-O, 2 leg, .81" throat, (TCM 830) adpt., B-O, RH, crnr. adpt., B-O, LH, crnr. adpt., B-O, 2 leg 1.125" throat adpt., B-O, 2 leg, Cat #8J2930 adpt., B-O, 2 leg, Komatsu #1 13-70-22140 adpt., B-O, 1-1/2 leg, 1.31" throat (Clark 55C) adpt., B-O, 2 leg, .93" throat adpt., B-O, step adpt., B-O, step adpt., B-O, 2 leg, .90" throat, (KSS-65Z) adpt., B-O, RH, crnr., refer to 650X160 adpt., B-O, LH, crnr., refer to 650X161 adpt., B-O, step adpt., B-O, 2 leg, 1.31" throat adpt., B-O, 2 leg, 1.18" throat adpt., B-O, 2 leg, 1.06" throat adpt., B-O, 2 leg, 1.06" throat adpt., B-O, H&L #L2145-23, L-4013-23 adpt., B-O, Case/Drott 4-in.-1, #26269 adpt., B-O, Case/Drott 4-in.-1, #229291 adpt., W-O, top leg, H&L #809-24 adpt., B-O, step adpt., B-O, 1.18" throat, Deere U41344 adpt., B-O, 2 leg, 1.31" throat adpt., W-O, bttm. Leg ripper box box pin (B926A) pin punch adpt. nose, W-O

TX160 TT160 TX160WT TX160F PMS160 PMX160HD TP160 T658X160 PM552X160 PM850X160 PM168X160 PM169X160 PM170X160 PM204X160 PM309X160 PM310X160 PM314X160 PM504X160 PM510X160 PM553X160 PM650X160 PM653X160 PM654X160 PM702X160 PM706X160 PM717X160 PM718X160 PM750X160 PM775X160 PM787X160 PM792X160 PM809X160 PM840X160 PM861X160 PM927X160 PM928X160 PMB926A PMP926 PM716PU PM160WN

rcv. disc.

non stock

9 9 9 9 9

STK STK STK STK STK N.S STK STK STK N.S N.S N.S N.S N.S N.S N.S N.S N.S N.S N.S N.S STK N.S N.S N.S N.S N.S N.S N.S N.S N.S N.S N.S N.S N.S N.S N.S STK STK STK STK

9 9

used on

JD: 80, 110, 190E, 290D, Competitive: backhoes, excavators

162 Series (Side Mount) style c f b d -

description tooth, tiger standard flare, 4" heavy duty twin tiger pin flex pin adpt., B-O, 1.31" throat, 30 deg, Clark 55C adpt., B-O, step adpt., B-O, step adpt., B-O, 2 leg, 1.06" throat adpt., W-O, bttm. leg, 1" to 1.25" adpt., B-O, 1.06" throat, (VME L-70) adpt., B-O, 1.25" throat, (VME L-90) adpt., B-O, LH, refer to 902X162 adpt., B-O, RH, refer to 902X163 adpt., B-O, 2 leg, 1.31" throat blade (162 nose) - RH blade (162 nose) - LH adpt. nose, W-O

part no. PMT162 PMX162 PMX162F PMX162HD PMX162WT TP160 PMP162 PM314X162 PM510X162 PM702X162 PM750X162 PM850X162 PM901X162 PM902X162 PM903X162 PM904X162 PM927X162 PM13V16R PM13V16L PM162WN

rcv. disc.

9

non stock STK STK STK STK N.S STK STK N.S N.S N.S N.S N.S N.S N.S N.S N.S N.S N.S N.S STK

used on

Hensley - Teeth by Series 220 Series (Top Mount) style e f c d b a a -

description

rcv. disc.

non stock

TF220 TX220 TT220 TX220WT TX220F TX220AP PMS220 PMX220ABR PMX220DP PMX220WTL PMT220L

9 9 9 9 9 9

pin TP160 adapter T109X220 adpt., B-O, 2 leg, 1.875" throat PM0C1X220 adpt., B-O, 2 leg, 1.625" throat PM3C1X220 adpt., W-O, 1-1/2 leg, 1" lip PM103X220 adpt., W-O, notched LH crnr. PM107X220 adpt., W-O, notched RH crnr. PM108X220 adpt., B-O, 1.125" throat, (D57S) PM111X220 adpt., B-O, crnr., RH, 1.15 thr PM112X220 adpt., B-O, crnr., LH, 1.15 thr PM113X220 adpt., B-O, 2 leg, .96" throat PM155X220 adpt., B-O, 2 leg, 1" throat PM168X220 adpt., B-O, RH, crnr. PM169X220 adpt., B-O, LH, crnr. PM170X220 adpt., B-O, step, IH #610986C1 PM211X220 adpt., B-O, ctr. (920, 930, 941B)(1U0257) PM257X220 adpt., B-O, crnr., Cat #3G4258 PM258X220 adpt., B-O, crnr., Cat #3G4259 PM259X220 adpt., B-O, step, IH #611606C1(270, 442, 444)PM270X220 adpt., B-O, 2 leg, 1.31" throat PM295X220 adpt., B-O, 2 leg, 1.06" throat PM310X220 adpt., B-O, 1.18" thr, 30deg (Case 750, 850) PM311X220 adpt., B-O, 2 leg 1"" throat, 25deg, Kom D41 PM410X220 adpt., B-O, 1.31" thr, ESCO #4738-25 (W36) PM473X220 adpt., B-O, 2 leg, 1.31" throat PM500X220 adpt., B-O, step, Cat #7J4415 PM613X220 adpt., stake-type (Poclain, PC8) PM615X220 adpt., B-O, ctr. 1.06" throat (Case 621, 855D) PM621X220 adpt., B-O, crnr. (Case 621) PM622X220 adpt., B-O, 2 leg, 1.03" throat PM700X220 adpt., B-O, RH, refer to 700X22 PM701X220 adpt., B-O, LH, refer to 700X22 PM702X220 adpt., B-O, step (Wabco 222G) PM703X220 adpt., B-O, step (Fiat-Allis 161) PM706X220 adpt., B-O, step (Wabco 222G) PM707X220 adpt., B-O, step PM710X220 adpt., B-O, 1.18" throat, (F-A 545B) PM730X220 adpt., B-O, 1.09" throat, Case #D49545 PM747X220 adpt., B-O step PM785X220 adpt., B-O step PM786X220 adpt., B-O, 1-1/2 leg, 1.06" throat PM796X220 adpt., B-O, 1-1/2 leg, .875" throat PM797X220 adpt., W-O, 1-1/4 leg, 1.5" throat PM809X220 adpt., B-O, 2 leg, 1.31" throat PM810X220 adpt., B-O, 2 leg, 1" throat PM811X220 adpt., B-O, 2 leg, 1.25" throat PM812X220 adpt., B-O, 1.06" throat, (Case W18) PM818X220 adpt., B-O, 1.31" throat PM824X220 adpt., W-O, bttm. leg, 2" to 2.25" PM855X220 adpt., B-O, 2 leg, 1.375" throat PM856X220 adpt., B-O, 1.68" throat PM857X220 adpt., B-O, step, Deere #T38783 PM860X220 adpt., B-O, 2 leg, 1.31" throat PM927X220 adpt. nose, W-O PM220WN

9 9

STK STK STK STK STK STK N.S STK STK STK STK STK STK N.S N.S STK STK STK N.S STK STK N.S N.S N.S N.S N.S N.S N.S N.S N.S N.S N.S N.S N.S N.S N.S N.S N.S STK STK N.S N.S N.S N.S N.S N.S N.S N.S N.S N.S N.S N.S N.S N.S N.S N.S N.S N.S N.S N.S N.S N.S N.S N.S STK

Fanggs standard tiger twin tiger flare abrasion paneled star abrasion down pitch twin tiger long tooth, tiger long

part no.

used on

Hensley - Teeth by Series 225 Series style

c f a a b -

description tiger std. abr. paneled abr. flare, 4.5"" twin tiger flex pin adpt., B-O, 2 leg, 1.875" throat adpt., W-O, bttm. leg, 2" lip adpt., W-O, 1-1/2 leg, 1" lip adpt., B-O, 1.125" throat adpt., B-O, 2 leg, .96" throat adpt., B-O, rev., crnr., Deere #112163 adpt., B-O, ctr., .81" throat adpt., B-O, ctr., 1.06" throat adpt., B-O, crnr. (544E, 624E) adpt., B-O, 2 leg, 1.06" throat adpt., B-O, LH, crnr., Cat #3G4258 adpt., B-O, RH, crnr., Cat #3G4259 adpt., B-O, 2 leg, 1.06" throat adpt., B-O, 1.43" thr, 22deg, Clark #251 147 adpt., B-O, 1.56" thr, 33deg, Deere T35385 adpt., B-O, 1.31" throat, 22deg (Case W36) adpt., B-O, 1.31" throat, Deere T29886 adpt., B-O, step adpt., B-O, LH, crnr. adpt., B-O, 1.06" throat adpt., B-O, step (Wabco 222G) adpt., B-O, 1.09" throat adpt., B-O, 1-1/2 leg, 1.06" throat adpt., B-O, 1-1/2 leg, .875" throat adpt., B-O, 2 leg, 1.31" throat adpt., B-O, 2 leg, 1" throat adpt., B-O, 1.06" throat adpt., B-O, 1.31", Case #L58824 adpt., W-O, bttm. leg, 2" to 2.25" lip adpt., B-O, 1.68" throat adpt., B-O, step, Deere #T38783 adpt., W-O, flush, 1.25" lip, 2" adpt., B-O, ctr., 1.43" throat adpt., B-O, LH, crnr., refer to 902X225 adpt., B-O, RH, crnr., refer to 902X225 adpt., nose, W-O

part no. PMT225 PMX225 PMX225AP PMX225ABR PMX225F PMX225WT PMP225 PM0C1X225 PM102X225 PM106X225 PM111X225 PM155X225 PM163X225 PM164X225 PM165X225 PM191X225 PM257X225 PM258X225 PM259X225 PM310X225 PM313X225 PM385X225 PM473X225 PM544X225 PM785X225 PM572X225 PM611X225 PM703X225 PM747X225 PM796X225 PM797X225 PM810X225 PM811X225 PM818X225 PM824X225 PM855X225 PM857X225 PM860X225 PM900X225 PM902X225 PM903X225 PM904X225 PM225WN

rcv. disc.

non stock STK STK N.S N.S N.S N.S STK N.S N.S N.S N.S N.S N.S N.S STK N.S N.S N.S N.S N.S N.S N.S N.S N.S N.S N.S N.S N.S N.S N.S N.S N.S N.S N.S N.S N.S N.S N.S N.S N.S N.S N.S STK

used on

Hensley - Teeth by Series 290 Series (Top Mount) style e f c d b a a

Fanggs

description

part no. TF290

standard tiger twin tiger flare abrasion panel abrasion pin flex pin adapter adapter adapter adapter adapter adapter adapter adapter adapter nose template kit for 290, 330 nose rebuild kit for 290 series flex pin, C-19 lips (136X290) flex pin, solid rubber pin removal tool for (290, 330) tooth, sharp, ribbed adpt., stake type, ESCO C-19 lip adpt., W-O, 1-1/2 leg, 2" lip adpt., W-O, 1-1/2 leg, RH, 1.75" adpt., W-O, 1-1/2 leg, LH, 1.75" adpt., stake type, Hensley C-19 adpt., B-O, 2 leg, 1.25" thr. adpt., B-O LH crnr. (955L) adpt., B-O RH crnr. (955L) adpt., W-O, bttm. leg, 1.25" to 1.5" lip adpt., B-O, 2 leg, 1.31" thr. 23deg, (955L) adpt., B-O, 2 leg, 1.93" thr. 23deg, (85Z11) adpt., B-O, LH (85Zll), (req. 486INS) adpt., B-O, RH (85Zll), (req. 486INS) adpt., B-O, LH (80Zlll) adpt., B-O, RH (80Zlll) adpt., B-O, 2 leg, 1.03" thr. (80ZIII) adpt., W-O, 1-1/2 leg, 1.375" lip adpt., stake type (Akerman H9, H11) adpt., B-O, ctr., 1.375" thr. adpt., B-O, crnr. (Case 721) adpt., B-O, crnr. (Case 821) adpt., B-O, ctr., 1.31" thr. (Case 821) adpt., B-O, Crnr (VME L-140) adpt., B-O, 2 leg, 1.56" thr. adpt. nose, W-O

TX290 TT290 TX290WT TX290F TX290AP PMX290ABR TK290 PMP290 T127X290 T158X290 PM125X290 PM150X290 PM190X290 PM191X290 PM673X290 PM674X290 PM822X290 PMA-TEM PMA290NR PMP136 PMP290STP PMPRT290 PMX290SYL PM119X290 PM124X290 PM130X290 PM131X290 PM136X290 PM156X290 PM308X290 PM309X290 PM383X290 PM430X290 PM480X290 PM486X290 PM487X290 PM488X290 PM489X290 PM490X290 PM580X290 PM589X290 PM721X290 PM722X290 PM820X290 PM821X290 PM904X290 PM905X290 PM290WN

rcv. disc.

non stock

9 9 9 9 9 9

STK STK STK STK STK STK STK STK STK STK STK N.S N.S STK STK N.S N.S N.S STK STK STK STK STK STK N.S N.S N.S N.S STK N.S N.S N.S N.S N.S STK STK STK N.S N.S N.S N.S N.S STK STK STK N.S N.S N.S STK

9 9 9

used on

JD: 490, 490D, 490E, 495D, 590D, 595, 595D, 120, 160LC, Competitive: excavators

295 Series (Top Mount) style f c d a b

description standard tiger twin tiger abrasion panel tooth, short, ribbed flare steel pin

part no. PM295 PMT295 PM295WT PM295AP PM295SYL PM295F PMP295

pin, steel spring adpt. 1-1/4" lip adpt., C-19 cast lip adpt. 1-1/2" lip adpt. B-O L.H. adpt., B-O R.H. adpt. bttm. leg W-O adpt., B-O adpt., stake type, Akerman H7 pin removal tool for P295SL adpt., W-O nose

PMP295SL PM127X295 PM136X295 PM158X295 PM308X295 PM309X295 PM383X295 PM430X295 PM589X295 PMP295SLRT PM295WN

rcv. disc.

non stock STK STK STK STK STK STK STK STK STK STK STK N.S N.S N.S N.S STK STK STK

used on

Hensley - Teeth by Series 300 Series (Side Mount) style c f a a b d

description tiger standard abrasion abrasion panel flare, 6"" heavy duty rock twin tiger flex pin (4 tab) adpt. nose, W-O

part no. PMT300 PMX300 PMX300ABR PMX300AP PMX300F PMX300R PMX300WT PMP300B PM300WN

rcv. disc.

non stock STK STK N.S N.S N.S N.S N.S STK STK

used on

Hensley - Teeth by Series 310 Series (Top Mount) style e

Fanggs pin

description

part no. TF310 TP160L

f c d b a a

standard tiger twin tiger flare tooth, 4" wide abrasion paneled abrasion pin flex pin, C-19 lip (136X310) adapter

TX310 TT310 TX310WT TX310F PMX310-4 TX310AP PM310ABR TP160 PMP136 T153X310

key refer also to PM142X330 adpt., stake-type, ESCO C-19 lip adpt., W-O, bttm. leg, 1.5" lip adpt., W-O, 1-1/2 leg, 2" lip adpt., W-O, flush, 1.25" lip adpt., W-O, 1-1/2 leg, 1.25" lip adpt., W-O, 1-1/2 leg, 1.25" lip adpt., W-O, RH, 1-1/2 leg, 1.75" adpt., stake-type, C-19 lip (reqs P136) adpt., B-O, 1-1/2 leg, 1.43" throat adpt., flush, 1.5" str. lip adpt., RH, flush, 1.5" sp. lip adpt., LH flush, 1.5" sp. lip adpt., W-O, RH, 1-1/2 leg, 1.5" lip adpt., W-O, LH, 1-1/2 leg, 1.5" lip adpt., B-O, 2 leg, 1.25" thr. adpt., W-O, 1-1/2 leg, 1.5" lip adpt., W-O, LH, notched crnr. adpt., W-O, RH, notched crnr. adpt., B-O, 2 leg, 1.43" thr. adpt., B-O, RH, crnr. adpt., B-O, LH, crnr. adpt., B-O, 1.46" thr. Komatsu D65, D75 adpt., B-O, 2 leg, 1.31" thr. adpt., B-O, 2 leg, 1.81" throat adpt., B-O, LH crnr. (955L) adpt., B-O, RH crnr. (955L) adpt., B-O, 1.31" thr., 22deg, Case 1450 adpt., B-O, specialty item adpt., W-O, bttm. leg, 1.25" to 1.5" lip adpt., B-O, 2 leg, 1.31" thr. 23deg, (955L) adpt., W-O, 1-1/2 leg, 1" lip adpt., B-O, step adpt., B-O, 2 leg, 1.81" thr, Furukawa 320A adpt., W-O, 1-1/2 leg, 1.375" lip adpt., stake-type (req. K668) adpt., B-O, 1-1/2 leg, 1.375" thr adpt., B-O, step adpt., B-O, step adpt., B-O, step adpt., B-O adpt., W-O, bttm. leg, 1.5" lip adpt., W-O, bttm. leg, .75" to .875" Lip adpt., W-O, 1.375" special lip adpt., B-O, 2 leg, 1.81" thr. (HD 6G, 12G) adpt., W-O, flush, 1.5" str. lip adpt., W-O, flush, LH, sp. lip adpt., W-O, flush, RH, sp. lip adpt. nose, W-O

PMK668 PM110X310 PM119X310 PM122X310 PM124X310 PM125X310 PM127X310 PM128X310 PM130X310 PM136X310 PM138X310 PM150X310 PM151X310 PM152X310 PM154X310 PM155X310 PM156X310 PM158X310 PM159X310 PM160X310 PM168X310 PM169X310 PM170X310 PM181X310 PM185X310 PM301X310 PM308X310 PM309X310 PM317X310 PM323X310 PM383X310 PM430X310 PM494X310 PM495X310 PM550X310 PM580X310 PM668X310 PM742X310 PM756X310 PM758X310 PM759X310 PM812X310 PM822X310 PM844X310 PM845X310 PM859X310 PM900X310 PM901X310 PM902X310 PM310WN

rcv. disc.

non stock

9 9 9 9 9 9

STK STK STK STK STK STK STK STK STK STK STK STK STK N.S N.S N.S N.S N.S N.S N.S N.S STK N.S N.S N.S N.S N.S N.S N.S STK STK STK N.S N.S N.S N.S N.S N.S N.S N.S N.S STK N.S N.S N.S N.S N.S N.S N.S N.S N.S N.S N.S N.S STK N.S N.S N.S N.S N.S N.S STK

9 9 9

used on

JD: 160LC, 200LC, 230LC, 270LC, 590D, 595, 595D, 690, 690A, 690B, 690C, 690D, 690E, 790, 790D, 790E, 792, 792D, Competitive: excavators, loaders

Hensley - Teeth by Series 330 Series (Top Mount) style e f c d b a a

Fanggs

description

part no. TF330

standard tiger twin tiger flare abrasion panel sharp, ribbed short rock abrasion pin flex pin adapter adapter adapter adapter adapter adapter nose rebuild kit for 330 Series lip fastener, C-19 lips (136X330, 136X310) lip fastener, C-29 lips (236X330) steel wedge adpt., stake-type, Hensley C-19 adpt., W-O, LH, notched crnr. adpt., W-O, RH, notched crnr. adpt., W-O, 1-1/2 leg, 1.625" lip adpt., stake-type, Hensley C-29 adpt., B-O specialty item (Sauerman) adpt., W-O, bttm. leg, 1.25"lip, 23deg adpt., B-O, ctr. (VME L150, L180) adpt., B-O, ctr. (Case 921) adpt., W-O, LH, notched crnr. adpt., W-O, RH, notched crnr. adpt. nose, W-O

TX330 TT330 TX330WT TX330F TX330AP PMX330SYL PMX330SR PMX330ABR TK330 PMP330 T158X330 PM190X330 PM743X330 PM744X330 PM822X330 PM937X330 PMA330NR PMP136 PMP236 PMW330 PM136X330 PM159X330 PM160X330 PM225X330 PM236X330 PM323X330 PM383X330 PM901X330 PM921X330 PM935X330 PM936X330 PM330WN

rcv. disc.

non stock

9 9 9 9 9 9

STK STK STK STK STK STK STK N.S STK STK STK STK N.S N.S N.S N.S STK STK STK STK STK STK STK STK N.S N.S STK N.S N.S N.S STK STK STK

9 9

used on

JD: 160LC, 200LC, 230LC, 270LC, 590D, 595, 595D, 690, 690A, 690B, 690C, 690D, 690E, 790, 790D, 790E, 792, 792D, Competitive: excavators

Hensley - Teeth by Series 335 Series (Top Mount) style f a b c d

description

part no.

standard abrasion panel flare short, ribbed tiger tooth twin tiger tooth steel pin

PM335 PM335AP PM335F PM335SYL PMT335 PM335WT PMP335

pin, steel spring adpt., 1.5" lip adpt., W-O, flush 1.625" - 1.75" lip, 30 deg adpt., C-29 Hensley cast lip adpt., stake (Akerman H12, 14, 16) adpt., L.H. crnr., 1.75" lip adpt., R.H. crnr. 1.75" lip adpt., 1.75" lip pin removal tool for P335SL adpt., W-O nose

PMP335SL PM158X335 PM190X335 PM236X335 PM355X335 PM935X335 PM936X335 PM937X335 PMP335SLRT PM335WN

rcv. disc.

non stock

used on

STK STK STK STK STK STK STK STK STK STK STK STK STK STK STK STK STK

350 Series (Top Mount) style f c a b d

description standard tiger abr. paneled, short flare twin tiger pin adpt. nose, W-O

part no. TX350 PMT350 PMX350APS PMX350F PMX350WT TP400HD PM350WN

rcv. disc.

non stock

9

STK STK N.S N.S STK STK STK

9

used on

Competitive: excavators

Hensley - Teeth by Series 370 Series (Top Mount) style e f c d a b a

Fanggs

description

part no. TF370

standard tiger twin tiger abrasion paneled flare sharp, ribbed abrasion steel keeper

TX370 TT370 TX370WT PMX370AP PMX370F PM X370SYL PMX370ABR TK370

flex pin, front lock pin removal tool for (370, 410, 450) fastener for Hensley C-29 lips adpt., stake-type, ESCO C-29 lip adpt., W-O, 1.5" lip adpt., stake-type, Hensley C-29 adpt., W-O, bttm. leg, 2" to 2.25" lip adpt. W-O, ctr., 2" lip adpt., W-O, RH/LH, 1.75" sp. lip adpt., W-O, ctr., 1.75" str. lip adpt., W-O, LH, 2" flush sp. lip adpt., W-O, RH, 2" flush, sp. lip adpt., W-O, ctr., 2" flush, str. lip adpt. nose rebuild kit for 370 Series adpt. nose, W-O

PMP370FL PMPRT370 PMP236 PM129X370 PM158X370 PM236X370 PM827X370 T940X370 PM936X370 PM937X370 PM947X370 PM948X370 PM949X370 PMA370NR PM370WN

rcv. disc.

non stock

9 9 9 9

STK STK STK STK STK STK STK STK STK STK STK STK N.S N.S N.S N.S STK N.S STK STK STK STK STK STK

9

9

used on

JD: 230LC, 270LC, 330LC, 370

385 Series (Top Mount) style e b c d

standard flare sharp, ribbed tiger twin tiger pin, steel pin, steel spring

description

part no. PM385 PM385F PM385SYL PMT385 PM385WT PMP385 PMP385SL

adpt., stake type, Hensley C29 adpt., stake (Akerman H12, 14, 16) adpt., W-O, bttm. leg adpt., W-O, 1-1/2 leg, 1.75" lip adpt., W-O, 1-1/2 leg, 2" lip adpt., W-O, flush, 2" lip pin removal tool for P385SL adpt., W-O nose

PM236X385 PM355X385 PM827X385 PM937X385 PM940X385 PM949X385 PMP385LRT PM385WN

rcv. disc.

non stock STK STK STK STK STK STK STK STK STK STK STK STK STK STK STK

used on

Hensley - Teeth by Series 400 Series (Top Mount) style e f c d b a a a

Fanggs

description

part no. TF400

standard tiger twin tiger flare abrasion paneled abrasion abrasion heavy short long sharp penetrator narrow pin slag pin slag pin slag pin wedge key adapter adapter adpt., stake-type, ESCO C-29 lip adpt., stake-type, for Hensley adpt., W-O, 1-1/2 leg, 1.5" lip adpt., W-O, bttm. leg, 2" to 2.25" adpt., W-O, 2 leg, ctr., 2" lip adpt., W-O, notched crnr., LH adpt., W-O, notched crnr., RH adpt., W-O, 1-1/2 leg, 2" lip adpt., W-O, 1-1/2 leg, 2" lip adpt., B-O, 2 leg, 1.75" thr. nose rebuild kit for 410 Series adpt. nose, W-O

TX400 TT400 TX400WT TX400F TX400AP PMX400ABR PMX400ABRB PMX400H PMX400LS PMX400SD TP400HD TP400SA TP400SB-S PMP400SB-OS PMK129C T802X400 PM800X400 PM129X400 PM236X400 PM604X400 PM827X400 PM830X400 PM831X400 PM832X400 PM938X400 PM940X400 PM945X400 PMA410NR PM400WN

rcv. disc.

non stock

9 9 9 9 9 9

STK STK STK STK STK STK STK STK STK STK STK STK STK STK STK STK STK N.S N.S STK STK N.S N.S N.S N.S STK N.S N.S STK STK

9

9

used on

JD: 200LC, 230LC, 270LC, 330LC, 370, 450LC, 690, 690A, 690B, 690C, 690D, 690E, 790, 790D, 790E, 792, 792D, 890, 890A, 892D, 892E, 992D, 992E, Competitive: excavators, loaders

410 Series (Top Mount) style e f d c a a b

Fanggs

description

part no. TF410

standard twin tiger tiger abrasion abrasion paneled flare long, sharp sharp, ribbed steel keeper adpt. W-O, 1-1/2 leg, 2" lip

TX410 TX410WT TT410 PMX410ABR PMX410AP PMX410F PMX410LS PMX410SYL TK410 T940X410

adpt., stake type Hensley C-29 adpt., W-O, 2 leg, 2" str. lip adpt., W-O, 2 leg, 2" sp. lip adpt., W-O, 2 leg, 2" sp. lip adapt., W-O bttm. leg adpt., W-O 1-1/2 leg 2" lip adpt., W-O 1-1/2 leg 1.75" lip adpt. nose, W-O

PM236X410 PMA464X410 PMA465X410 PMA466X410 PM827X410 PM890X410 PM937X410 PM410WN

rcv. disc. 9 9 9 9

9 9

non stock used on STK STK STK STK STK STK STK STK STK STK JD: 230LC, 270LC, 330LC, 370, 450LC STK N.S N.S N.S N.S N.S N.S N.S STK

450 Series (Top Mount) style description c tiger f standard a flare abrasion abrasion paneled d twin tiger adpt. nose, W-O

part no. PMT450 PMX450 PMX450F PMX450ABR PMX450AP PMX450WT PM450WN

rcv. disc.

non stock STK STK N.S STK STK STK STK

used on

part no. TF475

rcv. disc.

non stock

used on

Fanggs standard tiger twin tiger flare abrasion paneled abrasion slag heavy slag long slag h-bottom

TX475 TT475 TX475WT TX475F TX475AP PMX475ABR PMX475AH PMX475AHL PMX475AHS

9 9 9 9 9 9

STK STK STK STK STK STK N.S N.S N.S STK

475 Series (Top Mount) style a f c d b a a

description

Hensley - Teeth by Series long heavy slag tiger long twin tiger long pin adapter adapter adpt. nose, W-O

PMX475LP PMX475S PMT475L PMX475WTL TP475HD T303X475 PM988X475 PM475WN

9 9

N.S STK STK STK STK STK STK STK

JD: 270LC, 330LC, 450LC, 890, 890A, 892D, 892E, 992D, 922E, Competitive: excavators, loaders

500 Series (Top Mount) style f

description standard abrasion panel ribbed sharp tiger twin tiger steel key pin adapter

part no. TX500 TX500AP TX500SYL TT500 TX500WT TK500R T806X500

rcv. disc.

non stock

9 9 9

STK STK STK

9 9

STK STK

rcv. disc.

non stock

9

STK

9 9

STK STK

used on

JD: 550LC, 600CLC, 750, 800C

550 Series (Top Mount) style

description ribbed sharp tiger twin tiger steel key pin adapter

part no. TX550SYL TT550 TX550WT TK550R T806X550

used on

JD: 600CLC, 750, 800C

Hensley - Teeth by Series Sidecutters style

description strikeoff sidecutter, 3/1 pattern strikeoff sidecutter, 3/1 pattern strikeoff sidecutter, 2/2 pattern blade-type, 3/1 pattern blade-type, 3/1 pattern blade-type, 3/1 pattern blade-type, 3/1 pattern sidecutter, blade-type, RH, 2/2 sidecutter, blade-type, LH, 2/2 sidecutter, B-O, tooth-type, LH sidecutter, B-O, tooth-type, RH sidecutter, tooth-type, RH sidecutter, tooth-type, LH

part no.

rcv. disc.

PMSCB220-SO PMSCB330-SO PMSCB410-SO PMB311LH PMB312RH PMB330RH PMB331LH PMB102RH PMB103LH PM330X310 PM331X310 PM102X400 PM103X400

non stock

used on

STK STK STK STK STK STK STK STK STK N.S N.S N.S N.S

Hensley Attachments style

description

part no.

one-piece tooth, B-O PM099HX tooth, ctr., long, early style PM50CHX tooth, LH. long, early style PM50LH tooth, RH. long, early style PM50RH tooth, ctr. PM100CHX tooth, ctr. PM1020HX tooth, ctr., short PM500CHX tooth, LH PM100LH tooth, RH PM100RH tooth, LH, short PM500LH tooth, RH, short PM500RH tooth, ctr. PM1000HX tooth, LH PM1000LH tooth, RH PM1000RH tooth, ctr., continuous edge PM3000HX continuous edge ctr. tooth PM4330CHX continuous edge W-O nose PM4330WN closed lifting eye, large I.D., 10-20,000 lb. excaPM1025HX closed lifting eye, large I.D., 20-30,000 lb. excaPM2030HX closed lifting eye, large I.D., 30-40,000 lb. excaPM3040HX closed lifting eye, large I.D., 40-50,000 lb. excaPM4050HX closed lifting eye, large I.D., 50-60,000 lb. excaPM5060HX crnr. gusset PMCG6 crnr. gusset PMCG9 crnr. gusset PMCG12 closed eye lifting hook PM1030HHX closed eye lifting hook PM2060HHX closed eye lifting hook PM60100HX tooth, LH PM3000LH tooth, RH PM3000RH tooth, ctr., heavy PM3000H tooth, LH, heavy PM3000HLH tooth, RH, heavy PM3000HRH tooth, ctr. (round & T bucket) PM3000RC blade (156 nose) PM11V16L blade (156 nose) PM11V16R blade (162 nose) PM13V16L blade (162 nose) PM13V16R roll pin (2.25") PMP100 roll pin PM301P roll pin PM1000P pin PM9J2358P adpt., ctr. (156 nose) PM110HX adpt., LH (156 nose) PM110LH adpt., RH (156 nose) PM110RH adpt., ctr. (parabolic 400 nose) PM510HX adpt., LH (parabolic 400 nose) PM510LH adpt., RH (parabolic 400 nose) PM510RH adpt., ctr. PM1010HX adpt., LH PM1010LH adpt., RH PM1010RH adpt., ctr., continuous edge PM3010HX adpt., LH, continuous edge PM3010LH adpt., RH, continuous edge PM3010RH adpt., ctr. (round & T bucket) PM3010RC adpt., RH/LH (round & T bucket), less W-O nos PM3010RRL nose, W-O, ctr. PM1010WN nose, W-O LH PM1010WNL nose, W-O, RH PM1010WNR nose, W-O PM9J4354WN

rcv. disc.

non stock STK STK STK STK STK STK STK STK STK STK STK STK STK STK STK STK STK STK STK STK STK STK STK STK STK STK STK N.S. STK STK STK STK STK STK STK STK N.S. N.S. STK STK STK STK STK STK STK STK STK STK STK STK STK STK STK STK STK STK STK STK STK STK

used on

Hensley - Teeth by Series adpt. nose, W-O PM156WN nose, W-O PM220WN nose, W-O, LH (round & T bucket), ref. 3010RRPM3010LWN nose, W-O, ctr., (round & T bucket) PM3010WNRC nose, W-O, RH (round & T bucket), ref. 3010RRPM3010RWN nose, W-O, ctr. PM1030WN nose, W-O, ctr., continuous edge PM3010WN nose, W-O, LH, continuous edge PM3010WNL nose, W-O, RH, continuous edge PM3010WNR washer (old #3G9549W) PM6Y9459W

STK STK STK STK STK STK STK STK STK STK

Hensley - Teeth by Series Hensley Ripper Teeth - Applications 156 Series style c b

description

rcv. disc.

non stock

9 9

STK STK STK STK STK STK STK STK STK STK STK STK STK STK

rcv. disc.

non stock

9 9

STK STK N.S. STK STK STK STK STK STK STK STK STK

part no. PM 922X162 PM 926X162

rcv. disc.

non stock STK STK

used on

description

part no. PMT501 PM501HX PMB944 PMB977 PMP944 PM501P PMP977 PM944-501 PM977-501 PM501WN

rcv. disc.

non stock STK STK STK STK STK STK STK STK STK STK

used on

description tiger tooth tiger tooth, long twin tiger tooth twin tiger tooth, long std. tooth flex pin ripper sh., 28" (B977) ripper sh., 38" (B977) adpt. nose, W-O

part no. PMT702 PMT702L PMX702WT PMX702WTL PM702HX PM702P PM977-702 PM977-702L PM702WN

rcv. disc.

non stock STK STK STK STK STK STK STK STK STK

used on

tiger long star heavy duty star tiger, heavy duty flare, 4.375 heavy extra long roll pin box pin (B922B) ripper box ripper sh. (B922B) pin removal tool for P100, P156 nose, W-O

part no. TT156 TX156 PMS156 PMS156HD PMT156HD PMX156F PMX156H PMX156LP PM156 PM922 PMB922B PM922X156 PMPRT156 PM156WN

used on

160 Series style

description

part no.

tooth, tiger TT160 tooth, std. TX160 tooth, star PMS160 tooth, heavy duty PMX160HD adpt., B-O, 1-1/2 leg, 1.18 throat, 33 degrees ( PM552X160 adpt., W-O, bottom leg, 1-1 1/4 edge, 30 degrePM850X160 roll pin PM160 box pin (B926A) PM926 ripper box PMB926A ripper sh. (B922B) PM922X160 ripper sh. (B926A) PM926X160 pin removal tool for P160 PMRT160

used on

162 Series style

description box ripper sh. (B922B) box ripper sh. (B926A)

501 Series style teeth, tiger teeth, std. ripper box ripper box box pin (B944) flex pin (tooth) box pin (B977) ripper sh. (B944) ripper sh. (B977) adpt. nose, W-O

702 Series style

Hensley - Specifications

Ty pe

Type 1

Type 2

T Type 3

156 Series (Top Mount) style T T T T T T T T T T T T

description Fanggs standard tiger twin tiger tooth, star star h-d tiger h-d flare heavy extra long tooth, long tooth, twin tiger long adpt., ctr. (156 nose) adpt., RH (156 nose) adpt., LH (156 nose) adpt., nose, W-O blade (156 nose) blade (156 nose) adpt., W-O, 1-1/2 leg, .625" lip adpt., B-O, .81" thr., 29deg JCB 3C adpt., B-O, LH, crnr., refer to 300X156 adpt., B-O, RH, crnr. refer to 300X156 adpt., B-O, Deere no. U-41344 adpt., B-O, 1-1/2 leg, .93" throat adpt., B-O, 2 leg, step, Case #D35642 adpt., W-O, 1-1/2 leg, .625" lip adpt., W-O, 1-1/2 leg, .875" lip adpt., W-O, 1-1/2 leg, 1" lip adpt., B-O, .625" throat, 21deg adpt., W-O, 1-1/2 leg, .75"" lip adpt., W-O, flush, .75"" to .875" adpt., B-O, step (drott TD-6) adpt., B-O, 2 leg, 1.18" throat adpt., B-O, 2 leg, .81" throat adpt., W-O, bttm. leg, 1" lip adpt., W-O, bttm. leg, .625" to .875", ditch wit adpt., W-O, bttm. leg, .75"" to 1.0" lip 12" lip blade w/3 noses 14" lip blade w/3 noses 18" lip blade w/4 noses 24" lip blade w/5 noses ripper box nose weld-on

part no. TF156 TX156 TT156 TX156WT PMS156 PMS156HD PMT156HD PMX156F PMX156H PM156XLP PMX156L PMX156WTL PM110HX PM110RH PM110LH PM156WN PM11V16L PM11V16R PM230X156 PM300X156 PM301X156 PM302X156 PM344X156 PM350X156 PM401X156 PM548X156 PM549X156 PM550X156 PM551X156 PM552X156 PM681X156 PM682X156 PM683X156 PM684X156 PM805X156 PM835X156 PM836X156 PM12M156-12AHX PM14M156-12AHX PM18M156-12AHX PM24M156-12AHX PMB922B PM156WN

a 6" 4-1/4" 6-1/4" 6" 6" 6-1/16" 6-1/4" 5" 5-1/2" 6"

b 1-3/4" 1-3/4" 1/8" 3-1/8" 1-1/8" 1-1/8" point 4-3/8" 2 2-1/4"

3-1/4"

2-1/4"

c 1-5/8" 1-5/8" 1-5/8" 1-5/8" 1-5/8" 1-5/8" 1-5/8" 1-5/8" 1-5/8" 1-5/8"

d 1-5/8" 1-5/8" 1-5/8" 1-5/8" 1-5/8" 1-5/8" 1-5/8" 1-5/8" 1-5/8" 1-5/8"

lbs. 3.9 1.3 1.8 3.3 2.4 2.7 2.1 2.8 2.6 3.6 1.7 2.5 8.2 5.9 6.1 1.8 23.0 23.0 3.7 4.9 10.0 10.0 6.5 6.6 6.6 4.0 4.0 4.7 6.0 5.4 4.2 6.2 6.4 4.0 4.0 3.5 5.0 29.8 32.0 44.3 57.0 14.7 1.8

Hensley - Specifications 160 Series (Top Mount) style T T T T T T T 2

Fanggs standard tiger

description

part no. TF160 TX160 TT160

a 6-1/4" 6-7/8" 8-3/4"

b 2-1/8" 2-1/4" 1/4" 3-5/8" 6-5/8" 1" 2-5/16" 4-3/8"

c 1-5/8" 1-5/8" 1-5/8" 1-5/8" 1-5/8" 1-5/8" 1-5/8" 1-1/16"

d 2-3/8" 2-3/8" 2-3/8" 2-3/8" 2-3/8" 2-3/8" 2-3/8" 30°

twin tiger flare star std h.d. adapter adapter adapter adpt., B-O, 2 leg, .81" throat, (TCM 830) adpt., B-O, RH, crnr. adpt., B-O, LH, crnr. adpt., B-O, 2 leg 1.125" throat adpt., B-O, 2 leg, Cat #8J2930 adpt., B-O, 2 leg, Komatsu #1 13-70-22140 adpt., B-O, 1-1/2 leg, 1.31" throat (Clark 55C) adpt., B-O, 2 leg, .93" throat adpt., B-O, step adpt., B-O, step adpt., B-O, 2 leg, .90" throat, (KSS-65Z) adpt., B-O, RH, crnr., refer to 650X160 adpt., B-O, LH, crnr., refer to 650X161 adpt., B-O, step adpt., B-O, 2 leg, 1.31" throat adpt., B-O, 2 leg, 1.18" throat adpt., B-O, 2 leg, 1.06" throat adpt., B-O, 2 leg, 1.06" throat adpt., B-O, H&L #L2145-23, L-4013-23 adpt., B-O, Case/Drott 4-in.-1, #26269 adpt., B-O, Case/Drott 4-in.-1, #229291 adpt., W-O, top leg, H&L #809-24 adpt., B-O, step adpt., B-O, 1.18" throat, Deere U41344 adpt., B-O, 2 leg, 1.31" throat adpt., W-O, bttm. Leg ripper box adpt. nose, W-O

TX160WT TX160F PMS160 PMX160HD T658X160 PM552X160 PM850X160 PM168X160 PM169X160 PM170X160 PM204X160 PM309X160 PM310X160 PM314X160 PM504X160 PM510X160 PM553X160 PM650X160 PM653X160 PM654X160 PM702X160 PM706X160 PM717X160 PM718X160 PM750X160 PM775X160 PM787X160 PM792X160 PM809X160 PM840X160 PM861X160 PM927X160 PM928X160 PMB926A PM160WN

8-3/8" 4-1/2" 7-3/4" 6-5/8" 8" 6"

5-1/2"

1-1/4"

30°

lbs. 4.2 4.7 5.3 7.4 5.8 4.4 4.5 15.7 11.4 7.5 9.7 10.4 10.4 13.6 16.0 9.2 16.2 11.8 12.7 10.5 11.6 22.0 22.0 14.7 12.0 10.2 14.6 9.5 7.9 15.3 11.5 8.0 10.8 9.6 12.0 10.0 58.7 4.2

Hensley - Specifications 162 Series (Side Mount) style T T T T T

description tooth, tiger tooth, std. tooth, flare, 4" tooth, heavy duty tooth, twin tiger adpt., B-O, 1.31" throat, 30 deg, Clark 55C adpt., B-O, step adpt., B-O, step adpt., B-O, 2 leg, 1.06" throat adpt., W-O, bttm. leg, 1" to 1.25" adpt., B-O, 1.06" throat, (VME L-70) adpt., B-O, 1.25" throat, (VME L-90) adpt., B-O, LH, refer to 902X162 adpt., B-O, LH, refer to 902X163 adpt., B-O, 2 leg, 1.31" throat blade (162 nose) blade (162 nose) adpt. nose, W-O

part no. PMT162 PMX162 PMX162F PMX162HD PMX162WT PM314X162 PM510X162 PM702X162 PM750X162 PM850X162 PM901X162 PM902X162 PM903X162 PM904X162 PM927X162 PM13V16R PM13V16L PM162WN

a

b

c

d

lbs. 4.7 3.5 4.2 4.2 7.2 16.2 12.7 14.7 10.0 7.5 17.1 15.9 24.1 24.2 12.0 26.6 26.6 4.5

Hensley - Specifications 220 Series (Top Mount) style T T T T T T T T T T T T 2

Fanggs standard tiger twin tiger

description

part no. TF220 TX220 TT220 TX220WT

a 7" 7-1/8" 8" 8"

b 2-5/8" 2-3/4" 1/4" 3-7/8"

flare abrasion paneled nose weld-on star abrasion down pitch twin tiger tooth, tiger long adapter adapter adapter adapter adapter adapter adapter adapter adpt., B-O, 2 leg, 1.875" throat adpt., B-O, 2 leg, 1.625" throat adpt., W-O, 1-1/2 leg, 1" lip adpt., W-O, notched LH crnr. adpt., W-O, notched RH crnr. adpt., B-O, 1.125" throat, (D57S) adpt., B-O, crnr., RH, 1.15 thr adpt., B-O, crnr., LH, 1.15 thr adpt., B-O, 2 leg, .96" throat adpt., B-O, 2 leg, 1" throat adpt., B-O, RH, crnr. adpt., B-O, LH, crnr. adpt., B-O, step, IH #610986C1 adpt., B-O, ctr. (920, 930, 941B)(1U0257) adpt., B-O, crnr., Cat #3G4258 adpt., B-O, crnr., Cat #3G4259 adpt., B-O, step, IH #611606C1(270, 442, 444) adpt., B-O, 2 leg, 1.31" throat adpt., B-O, 2 leg, 1.06" throat adpt., B-O, 1.18" thr, 30deg (Case 750, 850) adpt., B-O, 2 leg 1"" throat, 25deg, Kom D41 adpt., B-O, 1.31" thr, ESCO #4738-25 (W36) adpt., B-O, 2 leg, 1.31" throat adpt., B-O, step, Cat #7J4415 adpt., stake-type (Poclain, PC8) adpt., B-O, ctr. 1.06" throat (Case 621, 855D) adpt., B-O, crnr. (Case 621) adpt., B-O, 2 leg, 1.03" throat adpt., B-O, RH, refer to 700X22 adpt., B-O, LH, refer to 700X22 adpt., B-O, step (Wabco 222G) adpt., B-O, step (Fiat-Allis 161) adpt., B-O, step (Wabco 222G) adpt., B-O, step adpt., B-O, 1.18" throat, (F-A 545B) adpt., B-O, 1.09" throat, Case #D49545 adpt., B-O step adpt., B-O step adpt., B-O, 1-1/2 leg, 1.06" throat

TX220F TX220AP PM220WN PMS220 PMX220ABR PMX220DP PMX220WTL PMT220L T109X220 PM100X220 PM106X220 PM102X220 PM385X220 PM544X220 PM611X220 PM900X220 PM0C1X220 PM3C1X220 PM103X220 PM107X220 PM108X220 PM111X220 PM112X220 PM113X220 PM155X220 PM168X220 PM169X220 PM170X220 PM211X220 PM257X220 PM258X220 PM259X220 PM270X220 PM295X220 PM310X220 PM311X220 PM410X220 PM473X220 PM500X220 PM613X220 PM615X220 PM621X220 PM622X220 PM700X220 PM701X220 PM702X220 PM703X220 PM706X220 PM707X220 PM710X220 PM730X220 PM747X220 PM785X220 PM786X220 PM796X220

7-1/2" 8" 4-7/8" 8-1/4" 8"

4-5/8" 3-1/2" 3 back 1-1/2" 3-3/8"

8-3/8"

220 Series (Top Mount)

c 2-1/4" 2-1/4" 2-1/4" 2-1/4" 2-1/4" 2-1/4"

4-1/8"

2-1/4" 2-1/4" 2-1/4" 2-1/4"

d 2-1/8" 2-1/8" 2-1/8" 2-1/8" 2-1/8" 2-1/8" 3-1/8 height 2-1/8" 2-1/8" 2-1/8" 2-1/8"

6" 9-1/2" 9-1/2" 8-1/2"

1-5/16" 8-1/2" 4-1/2" 7-1/4"

1" 1" 1-1/4"

30° 30° 25° 36°

8-7/8"

8-1/2"

1-1/4"

23°

lbs. 6.0 6.7 6.0 7.5 6.9 8.8 5.5 6.4 10.6 7.2 7.2 6.4 15.7 15.8 16.4 11.5 17.1 16.2 15.0 12.8 21.2 17.5 15.9 11.5 11.5 22.6 19.8 19.8 21.7 16.3 17.3 17.3 17.7 18.2 26.0 26.0 19.1 21.0 24.1 13.2 15.8 14.4 22.4 19.8 10.3 17.8 25.0 17.8 30.0 30.0 18.7 15.4 19.8 15.4 17.8 16.2 19.7 19.0 18.7

Hensley - Specifications adpt., B-O, 1-1/2 leg, .875" throat adpt., W-O, 1-1/4 leg, 1.5" throat adpt., B-O, 2 leg, 1.31" throat adpt., B-O, 2 leg, 1" throat adpt., B-O, 2 leg, 1.25" throat adpt., B-O, 1.06" throat, (Case W18) adpt., B-O, 1.31" throat adpt., W-O, bttm. leg, 2" to 2.25" adpt., B-O, 2 leg, 1.375" throat adpt., B-O, 1.68" throat adpt., B-O, step, Deere #T38783 adpt., B-O, 2 leg, 1.31" throat adpt. nose, W-O

PM797X220 PM809X220 PM810X220 PM811X220 PM812X220 PM818X220 PM824X220 PM855X220 PM856X220 PM857X220 PM860X220 PM927X220 PM220WN

13.5 10.8 16.7 19.3 25.0 12.0 12.4 13.7 23.0 21.5 17.2 14.0 5.5

225 Series (Side Mount) style T T T T T T

description tooth, tiger tooth, std. tooth, abr. paneled tooth, abr. tooth, flare, 4.5"" tooth, twin tiger adpt., B-O, 2 leg, 1.875" throat adpt., W-O, bttm. leg, 2" lip adpt., W-O, 1-1/2 leg, 1" lip adpt., B-O, 1.125" throat adpt., B-O, 2 leg, .96" throat adpt., B-O, rev., crnr., Deere #112163 adpt., B-O, ctr., .81" throat adpt., B-O, ctr., 1.06" throat adpt., B-O, crnr. (544E, 624E) adpt., B-O, 2 leg, 1.06" throat adpt., B-O, LH, crnr., Cat #3G4258 adpt., B-O, RH, crnr., Cat #3G4259 adpt., B-O, 2 leg, 1.06" throat adpt., B-O, 1.43" thr, 22deg, Clark #251 147 adpt., B-O, 1.56" thr, 33deg, Deere T35385 adpt., B-O, 1.31" throat, 22deg (Case W36) adpt., B-O, 1.31" throat, Deere T29886 adpt., B-O, step adpt., B-O, LH, crnr. adpt., B-O, 1.06" throat adpt., B-O, step (Wabco 222G) adpt., B-O, 1.09" throat adpt., B-O, 1-1/2 leg, 1.06" throat adpt., B-O, 1-1/2 leg, .875" throat adpt., B-O, 2 leg, 1.31" throat adpt., B-O, 2 leg, 1" throat adpt., B-O, 1.06" throat adpt., B-O, 1.31", Case #L58824 adpt., W-O, bttm. leg, 2" to 2.25" lip adpt., B-O, 1.68" throat adpt., B-O, step, Deere #T38783 adpt., W-O, flush, 1.25" lip, 2" adpt., B-O, ctr., 1.43" throat adpt., B-O, LH, crnr., refer to 902X225 adpt., B-O, RH, crnr., refer to 902X225 adpt., nose, W-O

part no. PMT225 PMX225 PMX225AP PMX225ABR PMX225F PMX225WT PM0C1X225 PM102X225 PM106X225 PM111X225 PM155X225 PM163X225 PM164X225 PM165X225 PM191X225 PM257X225 PM258X225 PM259X225 PM310X225 PM313X225 PM385X225 PM473X225 PM544X225 PM785X225 PM572X225 PM611X225 PM703X225 PM747X225 PM796X225 PM797X225 PM810X225 PM811X225 PM818X225 PM824X225 PM855X225 PM857X225 PM860X225 PM900X225 PM902X225 PM903X225 PM904X225 PM225WN

a

b

c

d

lbs. 5.0 6.2 8.4 11.0 6.0 8.5 21.2 15.8 16.4 22.6 21.7 15.8 12.3 14.2 20.5 18.2 24.8 24.8 24.1 23.6 17.1 14.4 16.2 19.7 15.0 15.0 18.7 16.2 18.7 13.5 16.7 19.3 12.0 12.4 13.2 21.5 17.2 12.8 24.1 30.0 30.0 5.7

Hensley - Specifications 290 Series (Top Mount) style T T T T T T 3 3

description Fanggs standard tiger twin tiger flare abrasion panel adapter adapter abrasion adapter adapter adapter adapter adapter adapter nose template kit for 290, 330 nose rebuild kit for 290 series tooth, sharp, ribbed adpt., stake type, ESCO C-19 lip adpt., W-O, 1-1/2 leg, 2" lip adpt., W-O, 1-1/2 leg, RH, 1.75" adpt., W-O, 1-1/2 leg, LH, 1.75" adpt., stake type, Hensley C-19 adpt., B-O, 2 leg, 1.25" thr. adpt., B-O LH crnr. (955L) adpt., B-O RH crnr. (955L) adpt., W-O, bttm. Leg, 1.25"" to 1.5" lip adpt., B-O, 2 leg, 1.31" thr. 23deg, (955L) adpt., B-O, 2 leg, 1.93" thr. 23deg, (85Z11) adpt., B-O, LH (85Zll), (req. 486INS) adpt., B-O, RH (85Zll), (req. 486INS) adpt., B-O, LH (80Zlll) adpt., B-O, RH (80Zlll) adpt., B-O, 2 leg, 1.03" thr. (80Z111) adpt., W-O, 1-1/2 leg, 1.375" lip adpt., stake type (Akerman H9, H11) adpt., B-O, ctr., 1.375" thr. adpt., B-O, crnr. (Case 721) adpt., B-O, crnr. (Case 821) adpt., B-O, ctr., 1.31" thr. (Case 821) adpt., B-O rev. crnr. VME L-14 adpt., B-O, 2 leg, 1.56" thr. nose weld-on

part no. TF290 TX290 TT290 TX290WT TX290F TX290AP T127X290 T158X290 PMX290ABR PM125X290 PM150X290 PM190X290 PM191X290 PM673X290 PM822X290 PMA-TEM PMA290NR PMX290SYL PM119X290 PM124X290 PM130X290 PM131X290 PM136X290 PM156X290 PM308X290 PM309X290 PM383X290 PM430X290 PM480X290 PM486X290 PM487X290 PM488X290 PM489X290 PM490X290 PM580X290 PM589X290 PM721X290 PM722X290 PM820X290 PM821X290 PM904X290 PM905X290 PM290WN

a

b

c

8-1/4" 3-1/4" 2-7/8" 8-1/4" 3-3/16" 2-7/8" 10" 3/16" 2-7/8" 9-3/4" 4-5/8" 2-7/8" 8" 6-1/4" 2-7/8" 8-1/2" 4" 2-7/8" 1-1/4" 7-1/2" 7-1/2" 1-1/2" 2-7/8" 8-3/16" 3-3/4" 1-1/4" 10" 9" 1-1/2" 10" 9" 3-13/32" 4-25/32" 1-5/16" 2-15/16"

4-3/4"

4-1/4"

3-5/8"

1-3/8"

d

lbs.

2-11/16" 2-11/16" 2-11/16" 2-11/16" 2-11/16" 2-11/16" 30° 30° 2-11/16"

10.4 8.6 8.8 10.2 11.6 10.4 21.5 22.7 10.2 23.2 19.9 21.5 21.5 27.5 22.0 11.4 2.3 9.2 18.8 24.3 22.6 22.6 20.1 31.2 39.5 39.5 18.7 30.0 24.3 34.8 34.8 37.1 37.1 23.8 20.2 26.6 21.0 24.0 27.0 24.0 36.2 26.3 7.3

1-3/16" 1-1/8"

Hensley - Specifications 295 Series (Top Mount) style T T T T T T

description std. tooth tiger tooth twin tiger tooth abr. panel tooth tooth, short, ribbed flare tooth adpt. 1-1/4" lip adpt., C-19 cast lip adpt. 1-1/2" lip adpt. B-O L.H. adpt., B-O R.H. adpt. bttm. leg W-O adpt., B-O adpt., stake type, Akerman H7 adpt., W-O nose

part no.

a

b

c

d

lbs. 8.2 8.7 10.5 10.8 10.3 12.8 21.9 20.6 22.8 39.8 39.8 19.2 30.2 26.8 8.1

a

b

c

d

lbs. 10.5 7.5 14.5 9.8 7.5 12.5 13.3 7.2

PM295 PMT295 PM295WT PM295AP PM295SYL PM295F PM127X295 PM136X295 PM158X295 PM308X295 PM309X295 PM383X295 PM430X295 PM589X295 PM295WN

300 Series (Side Mount) style T T T T T T T

description tooth, tiger tooth, std. tooth, abr. tooth, abr. paneled tooth, flare, 6"" tooth, heavy duty rock tooth, twin tiger adpt. nose, W-O

part no. PMT300 PMX300 PMX300ABR PMX300AP PMX300F PMX300R PMX300WT PM300WN

Hensley - Specifications 310 Series (Top Mount) style T T T T T T T 2

Fanggs standard

description

part no. TF310 TX310

a 7-1/2" 8"

b 3-1/4" 3-3/8"

c 3" 3"

d 2-1/8" 2-1/8"

tooth, std., 4" wide tiger

PMX310-4 TT310

9-7/8"

1/4"

twin tiger flare abrasion paneled adapter adapter key refer also to 142X330 adpt., stake-type, ESCO C-19 lip adpt., W-O, bttm. leg, 1.5" lip adpt., W-O, l-1/2 leg, 2" lip adpt., W-O, flush, 1.25" lip adpt., W-O, 1-1/2 leg, 1.25" lip adpt., W-O, 1-1/2 leg, 1.25" lip adpt., W-O, RH, 1-1/2 leg, 1.75" adpt., stake-type, C-19 lip (reqs P136) adpt., B-O, 1-1/2 leg, 1.43" throat adpt., flush, 1.5" str. lip adpt., RH, flush, 1.5" sp. lip adpt., LH flush, 1.5" sp. lip adpt., W-O, RH, 1-1/2 leg, 1.5" lip adpt., W-O, LH, 1-1/2 leg, 1.5" lip adpt., B-O, 2 leg, 1.25" thr. adpt., W-O, 1-1/2 leg, 1.5" lip adpt., W-O, LH, notched crnr. adpt., W-O, RH, notched crnr. adpt., B-O, 2 leg, 1.43" thr. adpt., B-O, RH, crnr. adpt., B-O, LH, crnr. adpt., B-O, 1.46" thr. Komatsu D65, D75 adpt., B-O, 2 leg, 1.31" thr. adpt., B-O, 2 leg, 1.81" throat adpt., B-O, LH crnr. (955L) adpt., B-O, RH crnr. (955L) adpt., B-O, 1.31" thr., 22deg, Case 1450 adpt., B-O, specialty item adpt., W-O, bttm. leg, 1.25"" to 1.5" lip adpt., B-O, 2 leg, 1.31" thr. 23deg, (955L) adpt., W-O, 1-1/2 leg, 1" lip adpt., B-O, step adpt., B-O, 2 leg, 1.81" thr, Furukawa 320A adpt., W-O, 1-1/2 leg, 1.375" lip adpt., stake-type (req. K668) adpt., B-O, 1-1/2 leg, 1.375" thr adpt., B-O, step adpt., B-O, step adpt., B-O, step adpt., B-O adpt., W-O, bttm. leg, 1.5" lip adpt., W-O, bttm. leg, .75"" to .875" adpt., W-O, 1.375" special lip adpt., B-O, 2 leg, 1.81" thr. (HD 6G, 12G) adpt., W-O, flush, 1.5" str. lip adpt., W-O, flush, LH, sp. lip adpt., W-O, flush, RH, sp. lip nose weld-on

TX310WT TX310F TX310AP T153X310 PMX310ABR PMK668 PM110X310 PM119X310 PM122X310 PM124X310 PM125X310 PM127X310 PM128X310 PM130X310 PM136X310 PM138X310 PM150X310 PM151X310 PM152X310 PM154X310 PM155X310 PM156X310 PM158X310 PM159X310 PM160X310 PM168X310 PM169X310 PM170X310 PM181X310 PM185X310 PM301X310 PM308X310 PM309X310 PM317X310 PM323X310 PM383X310 PM430X310 PM494X310 PM495X310 PM550X310 PM580X310 PM668X310 PM742X310 PM756X310 PM758X310 PM759X310 PM812X310 PM822X310 PM844X310 PM845X310 PM859X310 PM900X310 PM901X310 PM902X310 PM310WN

9-5/8" 7-7/8" 8-1/4" 7" 8-3/4"

4-3/4" 6" 4" 1-9/16" 4"

3" 3" 3" 3"

2-1/8" 2-1/8" 2-1/8" 2-1/8" 30° 2-1/4"

4-3/4"

3-3/4"

3"

lbs. 10.4 8.0 8.0 11.6 12.2 8.6 10.3 21.4 14.5 2.0 24.5 18.0 17.5 23.0 21.9 20.2 20.5 21.4 18.7 22.5 19.7 19.7 19.5 22.1 22.1 30.5 21.9 15.7 15.7 33.5 37.2 37.6 29.0 24.0 24.0 37.4 37.4 25.1 33.5 17.9 29.5 23.7 35.0 31.6 21.2 21.5 23.0 24.7 36.2 33.0 26.9 22.0 17.9 26.9 31.4 19.5 19.7 19.9 7.5

Hensley - Specifications 330 Series (Top Mount) style T T T T T T T T 2

description Fanggs standard tiger twin tiger flare abrasion panel tooth, sharp, ribbed short rock abrasion adapter adapter adapter adapter adapter adapter nose rebuild kit for 330 Series lip fastener, C-19 lips (136X330, 136X310) lip fastener, C-29 lips (236X330) steel wedge adpt., stake-type, Hensley C-19 adpt., W-O, LH, notched crnr. adpt., W-O, RH, notched crnr. adpt., W-O, 1-1/2 leg, 1.625" lip adpt., stake-type, Hensley C-29 adpt., B-O specialty item (Sauerman) adpt., W-O, bttm. leg, 1.25"" lip, 23deg adpt., B-O, ctr. (VME L150, L180) adpt., B-O, ctr. (Case 921) adpt., W-O, LH, notched crnr. adpt., W-O, RH, notched crnr. nose weld-on

part no. TF330 TX330 TT330 TX330WT TX330F TX330AP PM X330SYL PMX330SR PMX330ABR T158X330 PM190X330 PM743X330 PM744X330 PM822X330 PM937X330 PMA330NR PMP136 PMP236 PMW330 PM136X330 PM159X330 PM160X330 PM225X330 PM236X330 PM323X330 PM383X330 PM901X330 PM921X330 PM935X330 PM936X330 PM330WN

a 9-1/4" 9-1/4" 11-5/8" 11-5/8" 9-5/8" 9-1/2"

b 3-5/8" 3-5/8" 3/16" 5-1/4" 7-1/4" 4-1/2"

c 3-13/32" 3-13/32" 3-13/32" 3-13/32" 3-5/8" 3-5/8"

d 3-3/16" 3-3/16" 3-3/16" 3-3/16" 3-1/8" 3-1/8"

lbs. 15.3 11.9 11.9 14.7 18.1 15.4 14.9 14.4 15.5 35.2 32.9 64.0 44.0 28.3 32.9 2.7 0.8 2.1 0.8 24.8 28.7 28.7 30.4 47.8 41.4 23.5 41.0 29.0 29.4 29.4 10.9

8-3/8" 9-1/4" 8"

4-1/4" 4-1/4" 1-9/16"

3-5/8" 3-5/8"

3-1/8" 3-1/8" 30°

5-1/8"

4-1/4"

b

c

d

lbs. 12.5 15.1 17.9 15.3 13.2 15.3 34.6 34.5 48.7 38.3 31.7 31.7 33.1 12.1

b

c 3-1/2"

d 2-7/8"

lbs. 18.4 15.0 18.7 18.3 20.7 14.5

b

c

d

lbs.

335 Series (Top Mount) style T T T T T T

description std. tooth abr. panel tooth flare tooth tooth, short, ribbed tiger tooth twin tiger tooth adpt., 1.5" lip adpt., W-O, flush 1.625" - 1.75" lip, 30 deg adpt., C-29 Hensley cast lip adpt., stake (Akerman H12, 14, 16) adpt., L.H. crnr., 1.75" lip adpt., R.H. crnr. 1.75" lip adpt., 1.75" lip adpt., W-O nose

part no. PM335 PM335AP PM335F PM335SYL PMT335 PM335WT PM158X335 PM190X335 PM236X335 PM355X335 PM935X335 PM936X335 PM937X335 PM335WN

a

350 Series (Top Mount) style T T T T T

description standard tooth, tiger tooth, abr. paneled, short tooth, flare tooth, twin tiger adpt. nose, W-O

part no. TX350 PMT350 PMX350APS PMX350F PMX350WT PM350WN

a 11"

4"

370 Series (Top Mount) style

description

part no.

a

Hensley - Specifications T T T T T T T T 1

Fanggs standard tiger twin tiger abrasion paneled flare

TF370 TX370 TT370 TX370WT PMX370AP PM370F

tooth, sharp, ribbed abrasion steel keeper adpt. W-O, 1-1/2 leg, 2" lip fastener for Hensley C-29 lips adpt., stake-type, ESCO C-29 lip adpt., W-O, 1.5" lip adpt., stake-type, Hensley C-29 adpt., W-O, bttm. leg, 2" to 2.25" lip adpt. W-O, ctr., 2" lip adpt., W-O, RH/LH, 1.75" sp. lip adpt., W-O, ctr., 1.75" str. lip adpt., W-O, LH, 2" flush sp. lip adpt., W-O, RH, 2" flush, sp. lip adpt., W-O, ctr., 2" flush, str. lip nose rebuild kit for 370 Series nose weld-on

PM X370SYL PM370ABR TK370S T940X370 PMP236 PM129X370 PM158X370 PM236X370 PM827X370 T940X370 PM936X370 PM937X370 PM947X370 PM948X370 PM949X370 PMA370NR PM370WN

10-1/4" 10-1/4" 12" 12" 10-7/8" 10-1/4"

4" 4-1/8" point 6" 5" 8"

3-5/8" 3-5/8" 3-5/8" 3-5/8" 3-5/8" 3-5/8"

3-3/8" 3-3/8" 3-3/8" 3-3/8" 3-3/8" 3-3/8"

11-3/4"

4-5/8"

3-5/8"

3-3/8"

5-1/4"

10-3/4"

2-1/16"

30°

5-3/4"

4-5/8"

c

d

22.9 17.8 18.2 21.0 21.4 22.9 19.4 25.6 1.0 36.4 2.1 33.7 35.3 52.0 35.2 36.4 41.9 35.6 40.5 40.5 38.7 4.8 14.7

385 Series (Top Mount) style T T T T T

description tooth, std. tooth, flare tooth, sharp, ribbed tooth, tiger tooth, twin tiger adpt., stake type, Hensley C29 adpt., stake (Akerman H12, 14, 16) adpt., W-O, bttm. leg adpt., W-O, 1-1/2 leg, 1.75" lip adpt., W-O, 1-1/2 leg, 2" lip adpt., W-O, flush, 2" lip adpt., W-O nose

part no. PM385 PM385F PM385SYL PMT385 PM385WT PM236X385 PM355X385 PM827X385 PM937X385 PM940X385 PM949X385 PM385WN

a

b

lbs. 21.4 30.9 24.9 22.1 24.1 57.0 44.5 44.3 44.7 43.4 51.5 19.7

Hensley - Specifications 400 Series (Top Mount) style T T T T T T T T T T T

2

description Fanggs

part no. TF400

a 9-1/4"

b 4-1/2"

c 4" 4" 4" 4" 4" 4" 4" 4" 4" 4" 4"

d 2-7/8" 2-7/8" 2-7/8" 2-7/8" 2-7/8" 2-7/8" 3" 3" 3" 30 3"

standard tiger twin tiger flare abrasion paneled abrasion abrasion heavy short long sharp penetrator narrow slag pin slag pin slag pin adapter adapter wedge key adpt., stake-type, ESCO C-29 lip adpt., stake-type, for Hensley adpt., W-O, 1-1/2 leg, 1.5" lip adpt., W-O, bttm. leg, 2" to 2.25" adpt., W-O, 2 leg, ctr., 2" lip adpt., W-O, notched crnr., LH adpt., W-O, notched crnr., RH adpt., W-O, 1-1/2 leg, 2" lip adpt., W-O, 1-1/2 leg, 2" lip adpt., B-O, 2 leg, 1.75" thr. nose rebuild kit for 410 Series nose weld-on

TX400 TT400 TX400WT TX400F TX400AP PMX400ABR PMX400ABRB PMX400H PMX400LS PMX400SD PMP400SA PMP400SB-S PMP400SB-OS T802X400 PM800X400 PMK129C PM129X400 PM236X400 PM604X400 PM827X400 PM830X400 PM831X400 PM832X400 PM938X400 PM940X400 PM945X400 PMA410NR PM400WN

10" 12-1/4" 12-1/4" 10-1/2" 10-5/8" 11" 11" 8-7/8" 12-5/8" 10-3/4"

4" 3/8" 6" 8" 5-1/2" 4-3/4" 4-3/4" 4-3/4" 4-1/4" 2-1/4"

9"

2-1/16"

6"

5-1/4"

part no. TF410 TX410 TX410WT TT410 PMX410ABR PMX410AP PMX410F PMX410LS PMX410SYL TK410S T940X410 PM236X410 PMA464X410 PMA465X410 PMA466X410 PM827X410 PM890X410 PM937X410 PM410WN

a 11-1/4" 11-3/8" 13-5/8" 13-5/8" 13" 12" 11-3/8"

b 4-3/8" 4-9/16" 6-5/8" point 5-1/8" 5-1/2" 9"

c 4-1/16" 4-1/16" 4-1/16" 4-1/16" 4-1/16" 4-1/16" 4-1/16"

d 3-3/4" 3-3/4" 3-3/4" 3-3/4" 3-3/4" 3-3/4" 3-3/4"

5-1/4"

11"

2-1/16"

30°

30°

lbs. 10.4 16.2 18.6 24.1 21.6 21.8 25.8 28.9 21.7 23.0 17.9 0.3 0.3 0.3 48.0 40.0 2.5 36.5 54.0 36.8 48.0 45.3 41.0 41.0 44.9 46.0 52.0 5.3 16.7

410 Series (Top Mount) style T T T T T T T T T 1

description Fanggs standard twin tiger tiger abrasion abrasion paneled flare tooth, long, sharp tooth, sharp, ribbed steel keeper adpt. W-O, 1-1/2 leg, 2" lip adpt., stake type Hensley C-29 adpt., W-O, 2 leg, 2" str. lip adpt., W-O, 2 leg, 2" sp. lip adpt., W-O, 2 leg, 2" sp. lip adapt., W-O bttm. leg adpt., W-O 1-1/2 leg 2" lip adpt., W-O 1-1/2 leg 1.75" lip nose weld-on

lbs. 28.5 21.7 27.6 22.6 36.3 28.3 32.9 25.2 26.5 1.2 43.4 57.0 60.7 62.4 62.4 44.2 45.8 44.5 19.7

Hensley - Specifications 450 Series (Top Mount) style T T T T T T

description tiger standard flare abrasion abrasion paneled twin tiger nose weld-on

part no. PMT450 PMX450 PMX450F PMX450ABR PMX450AP PMX450WT PM450WN

a 15" 12-1/2" 12-1/2" 14-3/8" 13-1/4" 15"

b point 4-7/8" 10" 5-5/8" 6" 7-1/4"

c 4-9/16" 4-9/16" 4-9/16" 4-9/16" 4-9/16" 4-9/16"

d 4-5/16" 4-5/16" 4-5/16" 4-5/16" 4-5/16" 4-5/16"

lbs. 31.3 30.2 44.8 46.5 40.8 37.5 28.0

part no. TF475 TX475 TT475 TX475WT TX475F TX475AP T303X475 PMX475ABR PMX475AH PMX475AHL PMX475AHS PMX475LP PMX475S PMT475L PMX475WTL PM988X475 PM475WN

a 11-7/8" 12-1/2" 14-1/4" 14-3/8" 11-5/8" 13-1/4" 8/14" 13" 12-5/16" 15" 12-13/16" 12-1/8" 9-13/16" 15-1/2" 15-1/2"

b 5/34" 5/34" 1/4" 7" 8-7/8" 6-1/2" 2-9/16" 5-3/4" 5-3/4" 5-3/4" 6-3/4" 6-1/4" 5-3/4" point 7"

c 4-3/4" 4-3/4" 4-3/4" 4-3/4" 4-3/4" 4-3/4" 4-3/4" 4-3/4" 4-3/4" 4-3/4" 4-3/4" 4-3/4" 4-3/4" 4-3/4"

d 3-1/2" 3-1/2" 3-1/2" 3-1/2" 3-1/2" 3-1/2" 30° 3-1/2" 3-1/2" 3-1/2" 3-1/2" 3-1/2" 3-1/2" 3-1/2" 3-1/2"

7-1/4"

6-1/2"

lbs. 40.7 39.5 31.1 37.0 29.9 40.0 75.0 40.3 43.8 49.1 59.0 39.5 30.9 37.6 37.6 86.3 28.0

part no. TX500 TX500AP TX500SYL T806X500

a 14" 14-3/4" 15-1/2" 10"

b 5-5/8" 6-3/4" 6" 3-1/16"

c 5" 5" 5" 8"

d 4-11/16" 4-11/16" 4-11/16" 30°

lbs. 48.5 54.0 50.0 104.0

part no. TX550SYL T806X550

a 18-1/4" 12"

b 7" 3-1/16"

c 5-7/8" 9"

d 5-5/8" 30°

lbs. 91.0 165.0

475 Series (Top Mount) style T T T T T T 2

description Fanggs standard tiger twin tiger flare abrasion paneled adapter abrasion slag heavy slag long slag h-bottom long heavy slag tiger long twin tiger long adapter nose weld-on

500 Series (Top Mount) style T T T

description std. tooth abrasion panel ribbed sharp adapter

550 Series (Top Mount) style T

description ribbed sharp adapter

Hensley - Specifications Sidecutters style

description strikeoff sidecutter, 3/1 pattern strikeoff sidecutter, 3/1 pattern strikeoff sidecutter, 2/2 pattern blade-type, 3/1 pattern blade-type, 3/1 pattern blade-type, 3/1 pattern blade-type, 3/1 pattern sidecutter, blade-type, RH, 2/2 sidecutter, blade-type, LH, 2/2 sidecutter, B-O, tooth-type, LH sidecutter, B-O, tooth-type, RH sidecutter, B-O, tooth-type, RH sidecutter, B-O, tooth-type, LH

part no. PMSCB220-SO PMSCB330-SO PMSCB410-SO PMB311LH PMB312RH PMB330RH PMB331LH PMB102RH PMB103LH PM330X310 PM331X310 PM102X400 PM103X400

a

b

c

d

lbs. 21.9 33.0 41.8 29.8 29.9 45.2 45.2 59.2 59.5 28.0 28.0 61.0 61.0

part no. PM099HX PM50CHX PM50LH PM50RH PM100CHX PM1020HX PM500CHX PM100LH PM100RH PM500LH PM500RH PM1000HX PM1000LH PM1000RH PM3000HX PM4330CHX PM4330WN PM1025HX PM2030HX PM3040HX PM4050HX PM5060HX PMCG6 PMCG9 PMCG12 PM1030HHX PM2060HHX PM60100HX PM3000LH PM3000RH PM3000H PM3000HLH PM3000HRH PM3000RC PM11V16L PM11V16R PM13V16L PM13V16R PM110HX

a

b

c

d

lbs. 3.5 21.0 21.0 71.5 11.7 2.6 21.0 3.1 3.1 21.2 21.0 2.5 1.8 1.8 6.9 13.8 22.5 4.4 10.0 18.4 34.0 61.0 2.1 6.8 16.6 8.6 16.0 32.8 5.9 5.9 6.7 5.9 5.9 8.0 23.0 23.0 26.6 26.6 8.2

Hensley Attachments style

description one-piece tooth, B-O tooth, ctr., long, early style tooth, LH. long, early style tooth, RH. long, early style tooth, ctr. tooth, ctr. tooth, ctr., short tooth, LH tooth, RH tooth, LH, short tooth, RH, short tooth, ctr. tooth, LH tooth, RH tooth, ctr., continuous edge continuous edge ctr. tooth continuous edge W-O nose closed lifting eye, large I.D., 10-20,000 closed lifting eye, large I.D., 20-30,000 closed lifting eye, large I.D., 30-40,000 closed lifting eye, large I.D., 40-50,000 closed lifting eye, large I.D., 50-60,000 crnr. gusset crnr. gusset crnr. gusset closed eye lifting hook closed eye lifting hook closed eye lifting hook tooth, LH tooth, RH tooth, ctr., heavy tooth, LH, heavy tooth, RH, heavy tooth, ctr. (round & T bucket) blade (156 nose) blade (156 nose) blade (162 nose) blade (162 nose) adpt., ctr. (156 nose)

lb. lb. lb. lb. lb.

excav. excav. excav. excav. excav.

Hensley - Specifications Hensley Attachments style

description adpt., LH (156 nose) adpt., RH (156 nose) adpt., ctr. (parabolic 400 nose) adpt., LH (parabolic 400 nose) adpt., RH (parabolic 400 nose) adpt., ctr. adpt., LH adpt., RH adpt., ctr., continuous edge adpt., LH, continuous edge adpt., RH, continuous edge adpt., ctr. (round & T bucket) adpt., RH/LH (round & T bucket), less W-O nose nose, W-O, ctr. nose, W-O, LH nose, W-O, RH nose, W-O nose, W-O nose, W-O nose, W-O, LH (round & T bucket), ref. 3010RRL nose, W-O, ctr. (round & T bucket) nose, W-O, RH (round & T bucket), ref. 3010RRL nose, W-O, ctr. nose, W-O, ctr., continuous edge nose, W-O, LH, continuous edge nose, W-O, RH, continuous edge washer (old #3G9549W)

part no. PM110LH PM110RH PM510HX PM510LH PM510RH PM1010HX PM1010LH PM1010RH PM3010HX PM3010LH PM3010RH PM3010RC PM3010RRL PM1010WN PM1010WNL PM1010WNR PM9J4354WN PM156WN PM220WN PM3010LWN PM3010WNRC PM3010RWN PM1030WN PM3010WN PM3010WNL PM3010WNR PM6Y9459W

a

b

part no. TT156 TX156L PMS156 PMS156HD PMT156HD PMX156F PMX156H PMX156LP PM156 PMB922B PM922X156 PM156WN

a 6-1/4"

b 1/8"

6" 6-1/16" 6-1/4" 5" 5-1/2"

1-1/8" 1-1/8" point 4-3/8" 2"

description part no. tooth, tiger TT160 tooth, std. TX160 tooth, star PMS160 tooth, heavy duty PMX160HD adpt., B-O, 1-1/2 leg, 1.18 throat, 33 degrees (JD444) PM552X160 adpt., W-O, bottom leg, 1-1 1/4 edge, 30 degrees PM850X160 ripper box PMB926A ripper sh. (B922B) PM922X160 ripper sh. (B926A) PM926X160

a

c

d

lbs. 6.1 5.9 70.5 40.0 40.0 7.0 4.5 4.5 19.1 14.7 14.7 36.0 17.8 3.2 2.2 2.2 10.7 1.8 5.5 7.5 10.5 7.5 2.6 8.9 6.9 6.9 0.1

c 1-5/8"

d 1-5/8"

1-5/8" 1-5/8" 1-5/8" 1-5/8" 1-5/8"

1-5/8" 1-5/8" 1-5/8" 1-5/8" 1-5/8"

lbs. 1.8 1.7 2.4 2.7 2.1 2.8 2.6 3.6 0.1 14.7 23.0 1.8

Hensley Ripper Teeth - Specifications 156 Series style T T T T T T T T

description tooth, tiger tooth, long tooth star tooth, heavy duty star tooth , tiger, heavy duty tooth, flare, 4.375 tooth, heavy tooth, extra long roll pin ripper box ripper sh. (B922B) nose, W-O

160 Series style T T T T

b

c

d

lbs. 4.2 3.5 4.4 4.5 11.4 7.5 58.7 22.6 50.0

Hensley - Specifications 162 Series style

description box ripper sh. (B922B) box ripper sh. (B926A)

part no. PM922X162 PM926X162

a

b

c

d

lbs. 23.6 50.0

501 Series style T T

description

part no. TT501 PM501HX PMB944 PMB977 PM944-501 PM977-501 PM501WN

a

b

c

d

lbs. 12.5 10.7 80.0 164.0 72.5 114.0 14.0

description tiger tooth tiger tooth, long twin tiger tooth twin tiger tooth, long std. tooth ripper sh., 28" (B977) ripper sh., 38" (B977) nose, W-O

part no. TT702 TT702L PMX702WT PMX702WTL PM702HX PM977-702 PM977-702L PM702WN

a

b

c

d

lbs. 25.2 26.9 31.0 30.0 25.5 141.0 210.4 37.8

teeth, tiger teeth, std. ripper box ripper box ripper sh. (B944) ripper sh. (B977) nose, W-O

702 Series style T T T T T

Replacements for Hensley Products

Retainers


TK290 290 Series

TK330 330 Series

TP400HD 350, 400 Series

TP475 475 Series


Hensley 17

Replacements for Hensley Products

Retainers


TP156 - 156 Series (Except Fanggs)

TF13P - 156 Series (Fanggs or Other)

TP160 - 160; 220; 310 Series (Except 310 Fanggs)

TP160L - 310 Series Fanggs


Hensley 18

John Deere Replacements for H & L Products Various information can be determined from the part number system. Refer to the following charts for basic part numbering information.

Part Number Explanation for Teeth Part Number Explanation H & L Products Prefix TF TF T T T T T T T TT

Suffix D L F R SP L ST WT A, C CR

Examples: Part Number T250F Part Number T230ST

Explanation Fangg Digging Fangg Loading Standard Flare Rock Standard Long Star Twin Tiger Tiger Crimp-On Crimp-On Rock

Note: 1 or 2 digits in the part number indicates fabricated teeth. 3 digits in the part number indicates steel or ADI teeth. TF_P indicates Fanggs Flex Pin. T_P indicates STD Flex Pin.

25 Series Flare Tooth 23 Series Star Tooth

Part Number Explanation for Adapters Part Number Explanation for Replacement H & L Adapters Relate the correlating digit and part no. to the explanation below: Digit: 1 2 3 4 5 6 7 8 Part No.

T 4 2 7 X 2 4 0 T427X240 = Weld-On Center Adapter for 24 Series

Digit Explanation 1 (T) John Deere Part 2 Adapter Style Code 1 - Bolt-On Center 2 - Bolt-On End 3 - Weld-On End 4 - Weld-On Center 5 - Weld-On Left-Hand 6 - Weld-On Right-Hand 7 - Weld-On Bottom Leg 8 - Weld-On Flush Mount 9 - Scarifier/Ripper 3-4 Leg Spread (mm) 5 (X) Adapter Part 6-7-8 Tooth Series

Fanggs Digging Teeth (TF_D) (Non-Centerline)

Fanggs Loading Teeth (TF_L) (Non-Centerline)

Flare Teeth (T_F) (Centerline)

•

•

•

•

For general-purpose-toheavy digging. Provides a clean start and close crowd.

•

For general purpose to heavy digging/loading conditions. Flat bottom for better bucket control.

For digging in loose and mud-like conditions.

Standard Teeth (T_SP) (Non-Centerline)

Standard Teeth Fabricated (T_) (Non-Centerline)

Long Rock Teeth (T_R) (Non-Centerline)

•

•

•

•

For general-purpose to heavy-duty digging and loading Excellent penetration and wear.

For light-duty, general digging and applications.

•

For heavy-duty and extra heavy-duty applications. Additional wearlife.

Star Teeth (T_ST) (Non-Centerline)

Tiger Teeth (TT_) (Non-Centerline)

Twin Tiger Teeth (T_WT) (Non-Centerline)

•

•

•

Excellent penetration in rock, hardpan, and frost.

High penetration for frost and tough material.

•

For digging and loading in extremely tight material. Use as a corner tooth with tiger teeth in the center.

John Deere Replacements for H & L Products Various information can be determined from the part number system. Refer to the following charts for basic part numbering information.

Part Number Explanation for Teeth Part Number Explanation H & L Products Prefix TF TF T T T T T T T TT

Suffix D L F R SP L ST WT A, C CR

Examples: Part Number T250F Part Number T230ST

Explanation Fangg Digging Fangg Loading Standard Flare Rock Standard Long Star Twin Tiger Tiger Crimp-On Crimp-On Rock

Note: 1 or 2 digits in the part number indicates fabricated teeth. 3 digits in the part number indicates steel or ADI teeth. TF_P indicates Fanggs Flex Pin. T_P indicates STD Flex Pin.

25 Series Flare Tooth 23 Series Star Tooth

Part Number Explanation for Adapters Part Number Explanation for Replacement H & L Adapters Relate the correlating digit and part no. to the explanation below: Digit: 1 2 3 4 5 6 7 8 Part No.

T 4 2 7 X 2 4 0 T427X240 = Weld-On Center Adapter for 24 Series

Digit Explanation 1 (T) John Deere Part 2 Adapter Style Code 1 - Bolt-On Center 2 - Bolt-On End 3 - Weld-On End 4 - Weld-On Center 5 - Weld-On Left-Hand 6 - Weld-On Right-Hand 7 - Weld-On Bottom Leg 8 - Weld-On Flush Mount 9 - Scarifier/Ripper 3-4 Leg Spread (mm) 5 (X) Adapter Part 6-7-8 Tooth Series

Fanggs Digging Teeth (TF_D) (Non-Centerline)

Fanggs Loading Teeth (TF_L) (Non-Centerline)

Flare Teeth (T_F) (Centerline)

•

•

•

•

For general-purpose-toheavy digging. Provides a clean start and close crowd.

•

For general purpose to heavy digging/loading conditions. Flat bottom for better bucket control.

For digging in loose and mud-like conditions.

Standard Teeth (T_SP) (Non-Centerline)

Standard Teeth Fabricated (T_) (Non-Centerline)

Long Rock Teeth (T_R) (Non-Centerline)

•

•

•

•

For general-purpose to heavy-duty digging and loading Excellent penetration and wear.

For light-duty, general digging and applications.

•

For heavy-duty and extra heavy-duty applications. Additional wearlife.

Star Teeth (T_ST) (Non-Centerline)

Tiger Teeth (TT_) (Non-Centerline)

Twin Tiger Teeth (T_WT) (Non-Centerline)

•

•

•

Excellent penetration in rock, hardpan, and frost.

High penetration for frost and tough material.

•

For digging and loading in extremely tight material. Use as a corner tooth with tiger teeth in the center.

H & L Products

New Product

Polyurethane "Swamper" 2 Series style

f d -

description standard long rock adapter adpt., W-O, flush

part no. T2A T2AR T716X2A PML2520W2AHX

rcv. disc. non stock 9 9 JD: 172TX 9

used on

rcv. disc. non stock 9 9

used on

3 Series style

d h a a -

description part no. long rock T3CR flare T3CF standard PMT3C standard PM3CHXL adapter T716X3C adpt., W-O, flush, cast-in placPM1001-3CHX adpt., W-O, flush PM1002-3CHX

9

JD: 27ZTS, 35ZTS

23 Series style

g e a f b c h i d h j i -

description part no. fanggs d TF23D fanggs l TF23L pin TF23P standard T230SP standard T23 tiger TT230L twin tiger T230WTL flare T230F star T230ST long rock T23R flare PM23HXF Swamper T230SWPR tooth, star (heavy duty) PMS230 pin T23P pin PM23PB pin PM23PC pin PM23PD adapter T417X230 adapter T728X230 adapter U43792 PM230010 adapter adapter PM2300FL adpt., W-O, long leg on bttm.PMD834-23HX adpt. nose, W-O PM23WN adpt., W-O, .875" lip PM2740AW-23 adpt., W-O, .75" lip PM2740MW-23 12" lip blade, w/(3) PM12M480-12A 18" lip blade w/4 noses PM18M480-12A 24" lip blade w/5 noses PM24M480-12A

rcv. disc. non stock 9 9 9 9 9 9 9 9 9 9

used on

9 9

9 9 9

JD: Buckets with 23 Series-type adapter, 210C, 210CL, 300D, 500C, 510, 500A, 500B, 310, 310A, 310B, 310C, 310D, 310E, 310SE, 401D, 410, 410B, 410C, 410D, 410E, 315C, 315D, 315E, 510B, 510C, 510D, 610B, 610C, 710B, 710C, 710D, 315SE, 50ZTS, Skid-Steer: JD14, JD24, JD24-A, Case: 480F, 580K, 580L, 590, 590L, 680L, 780D, Competitive: Buckets with 23 Series-type adapters, Ford: 555D, 575D, 655D, 710D, 755B

H & L - Applications 24 Series style

a a I b c d h -

description standard standard rock star tiger twin tiger long sharp tooth, flare, 4" tip pin pin adapter adpt., W-O, misc. adpt., W-O, 1.25" lip adpt., nose, W-O

part no. T240

PM24HD PM24R PMS240 TT240 T240WT

rcv. disc. non stock used on Competitive: Backhoes with 24 Series-type adapters. 9 9 9 9 9 9

PM24SPHX PM24HXSS PM24HXF T24P

9

PM24PBHX T427X240 PM809-24HX PM2740-24HX PM24WN

9

N.S. N.S.

25 Series style description part no. TF252 g fanggs d - pin TF25P a standard T252 h flare T252F I star T252ST PM250TW c twin tiger d long PM251HX - pin T25P PM25/26PD - oversize pin - adapter PM2500150 - adapter T440X252 adpt., W-O, long leg on bttm. PM855-252HX adpt., W-O, 1.25" lip PM2740AW-252 adpt., W-O, 1.625" lip PM2740FW-252 adpt., W-O, long leg on bttm. PM3000W-252HX adpt., B-O (case 850/1150B) PML4079-252HX

rcv. disc. non stock used on 9 JD: 690, 690A, 690B, 690C, 690D, 690E, 200LC, 120LC Competitive: Excavators with 25-Series 9 type adapters 9 9 9 9 9

9 N.S.

N.S. N.S.

26 Series style

a a b

description standard standard tiger pin oversize pin

part no. T260 PM26HX PMT26 T25P PM25/26PD

rcv. disc. non stock used on 9 670, 670A, 670B, 672A, 672B, 170, 770A, 770B, 772A 772B, 772D BH, 772BH

9

27 Series style

a a a h d b c -

description part no. standard T271 PM27 standard standard PM271HX flare 7" PM27HXF long PM27HXL tiger PMT27 twin tiger PM27WT pin T27P adpt., W-O, long leg on bttm.PM3000W-27HX adapter PM2700150

rcv. disc. non stock used on 9 Competitive: Excavators with 27 Series-type adapters, Komatsu: PC150LC-5, PC200LC-5 9

N.S. 9 N.S.

H & L Ripper Teeth - Applications 18, 20, 21, 22, 23 Series style

description tooth, ripper, standard tooth, ripper, sharp tooth, ripper, tiger flex pin tooth, standard, rock tooth, standard, tooth, tiger tooth, ripper, standard tooth, ripper, standard flex pin adpt., nose, W-O ripper

part no. PM18HX PM18SSHX PMT18 PM18P PM20HXR PM20HXS PMT20 PM21HX PM22HX PM21/22 PM23RWN

rcv. disc. non stock N.S.

N.S. N.S.

used on

H&L - Specifications

Type 1

Type 2

T Type 3

2 Series style T T 2 T T T

description

part no.

standard T2A long rock T2AR adapter T716X2A standard PMT3C flare T3CF standard PM3CHXL adpt., W-O, flush PML2520W2AHX adpt., W-O, flush, cast-in place PM1001-3CHX adpt., W-O, flush PM1002-3CHX

a 4-1/4" 4-5/16" 4-3/4" 4-15/16"

b 1-3/4" 1-3/4" 1" 2-1/4"

c d 1-1/16" 1-1/16" 1-1/16" 1-5/16" 4" 30° 1-9/16" 1-11/16"

lbs. 1.1 1.2 1.5 1.4

2.4 3.9 3.7

18 Series style T T T

description rip standard rip sharp rip tiger

part no. PM18TL

a 10-1/2"

b point

c 2-1/2"

d 3-1/4"

lbs. 3.1

PM18HX PM18SSHX PMT18

10-5/9"

2-3/8"

2-1/2"

3-1/4"

14.7

9"

2-5/8"

2-1/2"

3-1/4"

10-1/2"

point

2-1/2"

3-1/4"

14

H&L - Specifications 23 Series style description T fanggs d T T T T T T T T T T T T -

-

fanggs l standard standard standard tiger twin tiger tiger h-d flare flare star long rock flare adapter adapter adpt., W-O, long leg on bttm. adpt. nose, W-O adpt., W-O, .875" lip adpt., W-O, .75" lip 12" lip blade, w/(3) 18" lip blade, w/4 noses 24" lip blade, w/5 noses adapter adapter adapter

part no. TF23D TF23L T230 T230SP T23 TT230 T230WT TT230HD T230F PM23HXF T230ST T23R PM23HXF PM230010 PM2300FL PMD834-23HX PM23WN PM2740AW-23HX PM2740MW-23HX PM12M480-12AHX PM18M480-12AHX PM24M480-12AHX T417X230 T728X230 U43792

a 6"

b 1-3/4"

c 1-1/2"

d 1-5/8"

lbs. 3.6

5-7/8"

1-3/4"

1-1/2"

1-5/8"

3.4

5-7/8" 5-7/8" 5-1/8" 6-3/4" 6-5/8" 6-3/16" 5-3/8"

2" 2" 2-1/4" 3/16" 3" 3/8" 4-3/4"

1-1/2" 1-1/2" 1-1/2" 1-1/2" 1-1/2" 1-1/2" 1-1/2"

1-5/8" 1-5/8" 1-5/8" 1-5/8" 1-5/8" 1-5/8" 1-5/8"

2.8 2.9 2 3.2 3.7 3.2 3.7

6-3/8" 5-7/16" 5-1/4" 3-3/8" 2-7/8"

2" 2-1/4" 4-3/8" 1-1/16" 3/4"

1-1/2" 1-1/2" 1-1/2" 2"

1-5/8" 1-5/8" 1-5/8" 23° 23°

3-5/8"

11/16" 3/4" 13/16"

1-3/4" 4-1/16" 1-1/2"

27° 25° 23°

2.6 2.4 3.2 4 3.8 3.1 1.7 3.4 4.3 31 43.7 59 3.7 3.1 3.5

3"

H&L - Specifications 24 Series style T T T T T T T T 2 T

description standard standard standard tiger twin tiger long sharp star adapter star pin tooth, flare, 4" tip adpt., W-O, misc. adpt., W-O, 1.25" lip adpt. Nose, W-O

part no.

PM24R TT240 T240WT PM24SPHX

a 6-3/4" 6-3/8" 6-1/2" 7-1/2" 7-1/2" 7-1/2"

b 2-1/4" 2-3/8" 2-3/8" 2-1/4" 2-1/8" 2-1/4"

c 1-9/16" 1-9/16" 1-9/16" 1-9/16" 1-9/16" 1-3/5"

d 2-1/8" 2-1/8" 2-1/8" 2-1/18" 2-1/8" 2-1/8"

PM24HXSS PMS240

6-4/5"

2-1/4"

1-3/5"

2-1/8"

7-5/8"

point

1-3/5"

2-1/8"

T427X240 PMS240 PM24PBHX PM 24HXF PM 809-24HX PM 2740-24HX PM 24WN

3-3/4"

1-1/8"

2"

23°

description fanggs d standard standard twin tiger flare

part no. TF252 T252 PM251HX

a 7-1/2" 6-7/8"

b 2-1/2" 2-7/8"

c 2-1/16" 2-1/16"

d 2-1/8" 2-1/8"

lbs. 8.8 6.7

PM250TW T252F

7-9/16" 6-3/4"

3-9/16" 5-3/4"

2-1/16" 2-1/16"

2-1/8" 2-1/8"

6.8 5.5

star long adapter adapter adpt., W-O, long leg on bttm. adpt., W-O, 1.25" lip adpt., W-O, 1.625" lip adpt., W-O, long leg on bttm. adpt., B-O, (case 850/1150B)

T252ST

8-1/4"

1-1/8"

2-1/16"

2-1/8"

6.1

PM251HX PM2500150

7-1/3" 3" 3"

2-7/8" 1-3/4" 1-9/16"

2" 2" 2"

2-1/8" 23° 23°

5.2 8 7.3 14 7.5 7.5 9.2 12

a 8-1/3" 9-4/5"

b 2-7/8" point

c 2" 2" 2" 2" 2"

d 2-4/5" 2-4/5" 2-4/5" 2-4/5" 2-4/5"

lbs. 8.5 8.7

a 7"

b 2-1/8"

c 2-7/8"

d 2-1/8"

lbs. 7.9

T240

PM24HD

lbs. 4.5 3.6 3.3 4 5.1 4.3 3.5 4.2 4.8

4.5 8.8 7.4 4

25 Series style T T T T T T T 2 3

T440X252 PM 855-252HX PM 2740AW-252HX PM 2740FW-252HX PM 3000W-252HX PM L4079-252HX

26 Series style T T T T T

standard tiger standard standard tiger

description

part no. PM26HX PMT26 T260 PM26HX PMT26

oversize pin pin

PM25126PD T25P

27 Series style description standard T

part no. T271

H&L - Specifications T T T T

standard standard flare long

PM27 PM271HX PM27HXF PM27HXL

7-1/2" 7.63 7" 9"

3-5/8" 3.69 7" 3-3/4"

2-7/8" 2.88 2-7/8" 2-7/8"

2-1/8" 2.13 2-1/8" 2-1/8"

8 8 8 9.6

T T 2

tiger twin tiger adapter adpt., W-O, long leg on bttm.

PMT27 PM27WT PM2700150 PM 3000W-27HX

9-1/2" 9" 7-7/8"

Point 4" 1-11/16"

2-7/8" 2-7/8" 3"

2-1/8" 2-1/8" 23°

9.5 10.3 20 13.1

part no. PM18HX PM18SSHX PMT18

a

b

c

d

lbs.

part no. PM20HXR PM20HXS PMT20

a

b

c

d

lbs.

part no. PM21HX

a

b

c

d

lbs.

part no. PM22HX

a

b

c

d

lbs.

part no. PM 23RWN

a

b

c

d

lbs.

H & L Ripper Teeth - Specifications 18 Series style

description tooth, ripper, standard tooth, ripper, sharp tooth, ripper, tiger

20 Series style

description tooth, standard, rock tooth, standard, tooth, tiger

21 Series style

description tooth, ripper, standard

22 Series style

description tooth, ripper, standard

23 Series style

description adpt., nose, W-O ripper

Replacements for H & L Hardware Illustrated parts are actual size.

T23P 23 Series

T24P 24 Series

TF23P 23 Series Fanggs

T25P 25 Series

TF25P 25 Series Fanggs

T27P 27 Series


H&L 14

Ripper and Scarifier Teeth John Deere offers a selection of both centerline and penetration-style ripper teeth. Remember these basic concepts: 1. Longer teeth offer more wearable material. 2. Shorter tips provide more strength. Generally, use a long centerline tooth because it provides good penetration and more wearable material. If better initial penetration is needed, use the penetration-style tooth.


Ripper/Scarifier and Miscellaneous 1

Rippers/Scarifiers

John Deere Scarifier Motor Graders

Series

Tooth Part No.

Standard

T1L Crimp-On

Shank

T114792

Series

Tooth Part No.

Standard

U15517

Pin

34M7070

Shank

T66192

Pin

U15522

Shank

T75520

Series

Tooth Part No.

Standard

T2D5572 Shank


T114792

-ALength 6″

-B-CWidth Point 1-9/16″ 3/16″ Fabricated 1.8 lb. JD: 570, 570A, 570B, 670B, 672B, 760, 760A, 770A, 770B, 772A, 772B

-ALength 5-7/8″

-B-CWidth Point 2-1/8″ 3/8″ Cast 3.1 lb. (34M7070) JD: 450G, 550G, 670, 670A, 670B, 672A, 672B, 770, 770A, 770B, 772A, 772B (U15522) JD: 350, 350B, 350C, 450, 450B, 450C, 455D, 455E, 555, 555A, 555B

-A-B-CLength Width Point 7-3/8″ 1-7/8″ 3/16″ JD: 570, 570A, 570B, 670A, 670B, 672A, 672B, 770A, 770B, 772A, 772B


Rippers/Scarifiers

John Deere Scarifier Motor Graders (Continued)

Series

Tooth Part No.

Standard

T260

Pin

T25P


Shank

T44319

-ALength 7-1/4″

-BWidth 3″

-CPoint 1/4″ Fabricated 9.0 lb. JD: 670, 670A, 670B, 672A, 672B, 770, 770A, 770B, 772A, 772B


Rippers/Scarifiers

Ripper Teeth

Reference 1

Reference 2

Series

Tooth Part No.

25 Series

EX25R12

Ref.

-ALength 12″

-BWidth 2″

-CPoint 1/4″ Cast

Pin Bushing

EX25RPG EX25RBG

Intermediate Centerline Top Bottom

Top Bottom

Penetration Pin

Penetration Pin

Pin Retainer

Pin

T9W2668

1

11-1/8″ 2″ 3/8″ 2-1/4″ 3-3/8″ T149204 (Shank) JD: 670B, 672B, 770B, 772B PM9J6586 (Shank) Cat: 4, 5, 6, 7, 12, 14, 16, 130, 140, 931, 941, 951, 955, 963, 973, 977, 983, D3, D4, D8, D8L, D8N, D9, D9L, D9N, D10, D10N, D10R, D11N, D11R 13-1/8″ 3″ 7/16″ 3-1/4″ 4-7/8″ Cat: D8, D8K, D8L, D8N, D8R, D9, D9N, D92, D94 14-1/2″ 2-1/4″ 7/16″ 2-3/4″ 4-7/16″ Cat: 4, 5, 6, 7, 12, 14, 16, 130, 140, 931, 941, 951, 955, 963, 973, 977, 983, D3, D8, D8L, D8N, D9, D9L, D9N, D10, D10N, D10R, D11N, D11R

PM4T5452 1

Cat: D8, D8L, D9

1

Cat: D9L, D10, D10N, D11

1

(No Shank Available) Cat: 943, 953

PM4T5502

PM3G0500

Penetration

PM9J4259 PM8E6258 PM8E6259


4-7/8″

Cat: D7, D8, D9

1

PM4T2479

Intermediate

3-3/8″

1

T6Y0359

Intermediate

3/8″

Cat: D8, D8K, D8L, D8N, D8R, D9, D9H, D9N, D9R

1

PM4T2479 PM6J8811

T8E6358 T8E6359

3-1/2″

1

PM9W2451

Long Pin Washer

15-1/8″

T6Y0309

T9W2668 T8E6359

Short

Deere: Misc.

PM7J3310

PM4J2479 PM6J8811

Long/Penetration Pin Washer

PM9W2452

PM4T2479 PM6J8811

Intermediate Top Bottom

2

Pocket Pocket Width Height 2-11/16″ 3-3/16″ 10.8 lb.


Rippers/Scarifiers Series

Tooth Part No.

Penetration Pin

Ref.

-ALength

-BWidth

-CPoint

PM4T5501 PM3G0500

Long Pin Retainer

Ripper Teeth (Continued)

1

(No Shank Available) Cat: D9L, D10, D10N, D11

PM1U3202 PM8E6208 PM8E6209

Short

(No Shank Available) Cat: 931, D3

PM1U3251 (No Shank Available) Cat: 943, 953



John Deere

Part No.

T75220 T66192

Part No.

T149204

Part No.

T44319

Part No.

T114792


Ripper Shanks

Description Scarifier - 40˚

A 19-1/2″

B 3-5/8″

C 1″

D 7/8″

E 1″

F 1″

G 3/4″

Wt. (lb.) 15.4

Scarifier - 28˚

19-1/2″

3-5/8″

1″

7/8″

1″

1″

3/4″

17.5

Description Shank

A 24-1/2″

B 5-1/2″

C 2-1/4″

D 4-13/64″

E 7″

Wt. (lb.) 88.4

Description Shank, Ripper

A 28-29/32″

B 5″

C 2″

D 2-1/2″

E 9″

Wt. (lb.) 75.3

Description Shank

A 19″

B 3″

C 1″

D 2-7/16″

E 1″


F 3/4″

G 3/4″

Wt. (lb.) 14.7

Miscellaneous Replacements

ADCO, Bofors, Case, Fiat-Allis, Ford, Komatsu

Reference 1

Reference 2

Series

Tooth Part No.

100 Series

T100C

Pin

TF13P

100 Series Pin

(Center)

Ref.

Part No.

-B-CPocket Pocket Width Point Width Height 3-3/16″ 1/2″ 1-5/8″ 1-5/8″ Cast 3.4 lb. Competitive: Backhoes with ADCO buckets.

1

11/16″ 1-5/8″ 1-5/8″ Cast 3.1 lb. Competitive: Backhoes with ADCO buckets.

T100 TF13P

-ALength 6-3/16″

6-3/16″

(Interchangeable right/left)

2

1/2″

Description

Pin / Description

PM3031537

Tooth

PM6254677 (Lock)

PM3031539

Tooth

PM6254682 (Lock)

PMD48212

Adapter, Weld-On

23 Series

PMD49586

Adapter, Bolt-On

23 Series

PMD49940

Adapter, Bolt-On

25 Series

Standard Tooth

PM20853P (Pin)

PM2027012130

Standard Tooth

PM0924402496

PM2057019570

Standard Tooth

PM0924402496

PM2077014151

Standard Tooth

PM1757821810

PM2087014152

Standard Tooth

PM0924403036

PM27

Fabricated Tooth

T27P

Bofors

Case

Fiat-Allis PM20853

Komatsu



Caterpillar Compactor Replacement Parts Model 834, 835 824B, 825B, 825G, 834, 835 825C, 825G 825C, 825G 815B 815, 815F

Dirt Tamping Foot PM8K9171* PM7K2939*** PM8K9171* PM2V6628 PM2V7053 PM8K9189**

Rock Tamping Foot PM7K2939***

Base (riser)

Cleaner Bar PM4S7928 PM3S3228

Rock Cleaner Bar PM4S7928 PM3S3228

PM3S3228 PM4V0668 PM4V3851

Cleaner Bar Retainer PM3S3225 PM3S3225 PM3S3225

PM5V4311# PM7K6908 PM5V4311# PM7K6908 PM4S7928

* Bolt-on requires (2) 7/8" X 2-1/2" bolt, (2) 7/8" nut, and (4) PM4D6419 washer ** Bolt-on requires (2) 5/8" X 2-1/2" bolt, (2) 5/8" nut, and (4) PM5S0581 washer *** Pin on foot # Finger shank, uses replaceable tip T3G8250, requires T9J2258 pin, T3G9609 retainer

PM3S3225

Your bucket tooth - Plasterer

Recommend Documents