BIX PRE-STAIN
BIX PRE-STAIN
tm
WOOD CONDITIONER MATERIAL SAFETY DATA SHEET COMPANY NAME AND ADDRESS: NFPA Rating: H=2, F=3, R=0 Office:
Plant:
(24 HOUR) EMERGENCY PHONE:
BIX MFG. CO.
BIX MFG. CO.
CHEMTREC: (800) 424-9300
108 Cude Lane
2011 Ashland City Hwy.
Effective: April 1, 1997
Madison, TN 37115
Ashland City, TN 37015
Supersedes: March 8, 1994
PHONE: (615) 868-0788 / (800) 251-1098
INGREDIENTS: Regulatory Information All ingredients used in BIX PRE-STAIN are TSCA listed. Most of the ingredients are regulated under Section 313 of Title III of SARA of 1986, and 40 CFR 372.45. Most of the ingredients are regulated as hazardous substances per 40 CFR 302 or 40 CFR 372.65. Material or Component
CAS Number
OSHA PEL
ACGIH TLV
Approx. %
Aliphatic Solvent Naphtha
64742-88-7
100 ppm
100 ppm
60 - 80 %
300 ppm
300 ppm
20 - 40 %
VM&P Naphtha
PHYSICAL DATA: Boiling Point
270-315°F
Specific Gravity @ 60°F
0.700 - 0.900
Vapor Pressure Formulation
Not determined
Melting Point
Approx. -30°C
Vapor Density (Calculated)
4.5
Appearance
Opaque liquid
Odor
Petroleum Naphtha odor
Solubility in Water
Immiscible
pH (10% Suspension)
6.2
Evaporation Rate (Ether=1)
Greater than 1
http://www.bixmfg.com/prestmsd.htm (1 of 4) [9/6/2001 5:09:26 AM]
BIX PRE-STAIN
% Volatiles (Oven, 100°C)
75.4% (w/w)
Relative Viscosity
Moderate
FIRE AND EXPLOSION HAZARD DATA: Flash Point: (Pensky-Martens CC)
32°F
Flammable Limits in Air
Not determined
Extinguisher Media
Water spray, dry chemical, carbon dioxide, and/or foam.
Special Fire Fighting Procedures
Fire fighter should have eye and full face protection and wear self contained breathing apparatus.
Unusual Fire and Explosion Hazards
Vapors are heavier than air and may travel to a source of ignition and flash back.
PHYSICAL HAZARDS / REACTIVITY DATA: Stability
Stable
Conditions to Avoid
High temperatures
Incompatibility
Strong acids and/or oxidizers
Hazardous Polymerization
Will not occur
Hazardous Decomposition
Combustion produces unidentified organics, oxides of carbon, carbon dioxide, carbon monoxide, ammonia, nitrogen oxides, hydrogen chloride, phosgene, and various hydrocarbons.
Other
Do not add nitrites due to possible formation of nitrosoamines (potential carcinogen).
SPECIAL PRECAUTIONS FOR SAFE HANDLING AND USE: Handling and Storage
Store in cool ventilated area away from ignition sources. Do not store above 100°F. Keep containers tightly closed. Do not cut, puncture, or weld on or near empty or full drums.
Other Precautions
Avoid oxidizers. No smoking or eating in handling areas. Wash hands after using and before smoking or eating. Emptied containers may retain hazardous residue and explosive vapors. Keep away from heat, sparks and flames. Follow all hazard precautions given in this data sheet until container is thoroughly cleaned or destroyed.
Material Release or Spill
Evacuate the area, ventilate, and avoid breathing vapors. Remove all sources of ignition (flames, hot surfaces, and electrical, static, or frictional sparks). Dike area to contain the spill. Wearing protective equipment, clean up spill on absorbent, non-combustible material and place in covered containers for disposal. Do not flush to sewer or open water. Avoid contamination of ground and surface waters.
Disposal of Material
Dispose of in accordance with local, state and federal regulations. Do not incinerate closed containers.
HEALTH HAZARD DATA: Route of Entry: Inhalation: Yes Skin: Yes Ingestion: Yes Health Hazards (Acute and Chronic): Aliphatic Solvent Naphtha: http://www.bixmfg.com/prestmsd.htm (2 of 4) [9/6/2001 5:09:26 AM]
BIX PRE-STAIN
No data available. Chemical ingredients listed as a carcinogen or potential carcinogen: National Toxicology Program: None IARC Monographs: None OSHA Regulated: None Signs and Symptoms of Exposure: Skin Contact causes irritation. Can cause defatting of skin which may lead to dermatitis. Eyes Contact causes irritation. Symptoms are tearing, redness and discomfort. Inhalation Causes nasal, respiratory, and throat irritation, headache, nausea, drowsiness, breathlessness, fatigue, central nervous system depression, convulsions, and loss of consciousness. Extended or repeated exposure to concentrations above the recommended exposure limits may cause brain or nervous system depression, with symptoms such as headache or nausea and if continued indefinitely, loss of consciousness, liver and kidney damage. Reports on one of the product’s components have associated repeated or prolonged occupational overexposure to solvents with permanent brain and nervous system damage. Intentional misuse by deliberately concentrating and inhaling the contents may be harmful or fatal. Ingestion Aspiration hazard. May cause mouth, throat, esophagus and stomach irritation, nausea, vomiting, diarrhea, headache, drowsiness, fatigue, pneumonitis, pulmonary edema, central nervous system depression, convulsions and loss of consciousness. Medical Conditions That May Be Aggravated by Exposure to This Product: Preexisting eye, skin, liver, kidney and respiratory disorders. Emergency and First Aid Procedures for Overexposure: Inhalation Move to fresh air. If necessary, restore and support breathing. Get prompt medical attention. Eyes Immediately flush with water for 15 minutes while lifting eyelids and rolling eyes. Get immediate medical attention. Skin Remove contaminated clothing and shoes. Wash exposed areas thoroughly with large quantities of water for at least 15 minutes. Launder contaminated clothing before reuse. Get prompt medical attention. Ingestion ONLY induce vomiting at the advice of a physician. Get immediate medical attention. Never give anything by mouth to an unconscious person. SPECIAL PROTECTION AND CONTROL MEASURES: Respiratory Protection
Do not breathe vapors. Wear an appropriate, properly fitted respirator (NIOSH/MSHA approved) during use of this product until vapors are exhausted, unless air monitoring demonstrates vapor levels are below applicable limits.
Ventilation
Provide general clean air dilution or local exhaust ventilation in volume and pattern to keep the air contaminant concentration below the lower explosion limit and below current applicable exposure limits.
Protective Gloves
Use solvent impermeable, chemical resistant gloves such as nitrile, neoprene, or other resistant material which is also resistant to naphtha.
Eye Protection
Chemical goggles, safety glasses with side shields, or face shield should be worn when working with this material. Contact lenses should not be worn when working with this material.
Other Protective Equipment
Eye fountain and/or safety shower should be readily accessible. Long sleeves, aprons or other personal clothing protection should be worn to avoid contact with this material.
Work Hygiene Practices
Avoid contact with this material. Do not eat, drink, or smoke when working with this material.
http://www.bixmfg.com/prestmsd.htm (3 of 4) [9/6/2001 5:09:26 AM]
BIX PRE-STAIN ● ❍
Note: Personal protection information given is based upon the general information as to normal uses and conditions. Where special or unusual uses or conditions exist, it is suggested that the expert assistance of an industrial hygienist or other qualified professional be sought.
The data contained herein is based on information currently available to BIX Mfg. Co., Incorporated and is believed to be factual. As a formulator, blender, and compounder, BIX Mfg. Co., Incorporated does not manufacture the raw materials used in this product and correspondingly relies on information provided to BIX Mfg. Co., Incorporated from material safety data sheets on the specific raw materials in the construction of this material safety data sheet. Such information is to the best of BIX Mfg. Co., Incorporated’s knowledge and belief to be accurate and reliable as of the date of this MSDS. HOWEVER, NO REPRESENTATION, WARRANTY OR GUARANTEE IS MADE AS TO THE ACCURACY, RELIABILITY, OR COMPLETENESS. It is the user’s responsibility to satisfy himself as to the suitability and completeness of such information for his own particular application. This information is not intended to be all-inclusive as to the manner and conditions of use, handling and storage. Other factors may involve other or additional safety or performance considerations. This data is not to be taken as a warranty or representation of which BIX Mfg. Co., Incorporated assumes legal responsibility.
Bix Pre-Stain Home Page | Bix Pre-Stain Technical Data Sheet Bix Home Page | Products | Tips from Mr. Bix | Technical Data Sheets | Manufacturer Safety Data Sheets Company Information | E-mail the Author THIS SITE BEST WHEN VIEWED WITH
http://www.bixmfg.com/prestmsd.htm (4 of 4) [9/6/2001 5:09:26 AM]
