→ PV
DC 30V/3A COS￠=1
Alarm O U T 1 O U T 2 / AL1 AT/M AL2
SET
/M
↑ ↑ ⑤ ⑥
T/C
⑦
S
0～1600℃
E
0～1000℃
Rt
Pt100 Cu50
-199～600℃ -50～150℃
mV
mV mA
mA
＋
F
↑
C
B
9:96H × 96W TA series of temperature controller
＞＞
/M
Confirm Modify
SET
Shift and flashes
Stop flashing
↑ E
G
H
In Manual operation/Non-autotune estate, press and hold / key for more than 3 seconds to enter/quit the below ＞＞
E:24VDC or 18-30V AC/DC Sizes: 4:48H × 48W 6:48H × 96W 7:72H × 72W 8:96H × 48W
Measured displaying Set displaying
↓
↑
S:SSR/Logic T:SCR Power supply:Default:90-260V AC/DC
Input up limit
↓ 3S
＋ ＋
D
＋
Input type
↓ 3S
A
Mounting and Sizes
↑
Displays temperature unit
Input low limit
menu for display range settings.
↓
Input signals:Default: K,J,T,S,Pt100/mA,lN
-T:SCR N:Non OUT1: I:4-20mA R:RELAY
↓ 3S
0-75mV
35～85%RH ≤ 350g
Environment humidity Weight
⑦.Down key
AL1:R:RELAY S:SSR/Logic T:SCR
Power on
4-20mA /0-10V Withstand voltage strength 1500V Rms (Between power terminal and the housing) Insulation resistance Min 50M Ω(500V DC)(Between power terminal and the housing) Environment temperature 0～50℃ -10～60℃ Save temperature
Models TD □□ - □□□□
autotuning estate.Press again to quite.
Self-check All LED on
AT lamp off. ⑥.Up key
In display estate,press SET and <
↑
⑤.Shift/Autotune key Press this key to shift digit of parameter value setting. Or hold this key for more than 3 seconds can enter/quit autotune estate. When enter autotune estate, AT lamp on. When quit autotune estate,
0～999℃/0～1200℃ 0～999℃ /0～1200℃ -150～400℃ (Special order)
impossible. ☆ Antotuning operation.
＞＞
①. PV / parameter symbols ②. SV / parameters preset value ③. Indication lamps OUT1: Heating/Main control output lamp On: Output Off: No output OUT2/AL2: Colling/Alarm 2 output lamp On: Output Off: No output AT/M: On: manual operation Off: auto operation Flash: under autotuning estate P/MV: SV/MV display setting On: MV manual output Off: SV setting AL1: Alarm 1 lamp On: Alarm Off: No Alarm AL2: Alarm 21 lamp On: Alarm Off: No Alarm ④.Set key Parameter Setting/Changing
Input
K J T
and
key to modify the numerals; D: Press SET key to confirm. ☆ In autotuning estate,output value modification is
＞＞
→ → P/MV
RELAY: normal open AC 250V/3A DC 30V/3A COS￠=1 SSR/LOGIC:24V DC12V/ 30mA
↑ ↑
TA series of temperature controller is available for many TC or RTD input, adopt some advanced techonology such multi digital filter circuit, autotune PID, fuzzy PID that make it is very precise, stable, strong anti-interference and simple operation. The instrument is widely applied to
AC 250V/3A
SSR/LOGIC ：24V DC ± 2V/ 20mA
OUT2/AL2: R:RELAY S:SSR/Logic
Applications
RELAY：normal open
Main output
SV
→
operation & input connect do MV settable. B: Press the ＜＜ / M key to select the digit you want to modify; C: Press
≤ 300ms
↑
This instrument should be installed in a domestic environment. Otherwires electricla shock, fire or malfunction may result. To avoid using this instrument in environment full of dust or caustic gas. To avoid using this instrument in environment of strong shock or concussion. To avoid using this instrument in environment of overflow water or explosive oil. The power supply wire should not put together with large current wire to aviod electromagnetic radiation, If it must to put together, we suggest to use a individual pipe. In case the instrument is used in environment of strong noise, (such as motor, transformer, solenoid, etc.) A current suppresser or noise filter should be used.
0.3%F.S ± 2digit
↑
Caution
④
-199～1800℃
Accuracy Sampling cycle
>>
Please do not turn on the power supply until all of the wiring is completed. Otherwise electrical shock, fire or malfunction may result. Do not wire when the power is on. Do not turn on the power supply when cleaning this instrument. Do not disassemble, repair or modify the instrument. This may cause electrical shock, fire or malfunction.Use this instrument in the scope of its specifications. Otherwise fire or malfunction may result.The use life of the output relay is quite different according to is capacity and condictions. If use out of its scope, fire or malfunction may result.
③
Display range
while off means MV manual output setting,but only on manual
↓
②
Warning
≤ 5VA
↑
①
A: In display estate,press SET,P/MV lamp on means SV setting,
Consumption
＞＞
Panel
Parameter Setting &Autotuning ☆ Parameters setting:
90-260V AC/DC 50/60Hz
Power supply
＞＞
Thanks a lot for selecting the product! Before operating this instrument, please carefully read this manual and fully understand its contents. If any probroms, please contact our sales or distributors whom you buy from. This manual is subject to change without prior notice.
Specifications
↑
Instruction Manual
>>
TD Series Temperature Controller
automation systems of mechanism, chemical industrial, chinaware, light industrial, metallurgy and petroleum chemical industrial. It is also applied to the production line of foodstuff, packing, printing, dry machine, metal heat process equipment to control the temperature.
>>
MYPIN
Low limit value, it is adjustable
Sizes Model
A
B
C
D
E
F
G
H
TD4
44.5+0.5
45+0.5
65
65
48
48
8
80
TD6
43.5+0.5
91+0.5
65
115
48
96
12
80
TD7
91+0.5
91+0.5
115
115
96
96
12
100
TD8
91+0.5
43.5+0.5
65
115
96
48
12
80
TD9
67.5+0.5
67.5+0.5
95
95
72
72
12
100
↓
by the input signal. SET
Up limit value, it is adjustable by the input signal.
↓
SET
AL1 hysteresis setting value. Range ± 90, factory setting 1.0
↓ SET 1
SET
AL2 mode: The same as AL1. SET
Range: ± 100.Display value PV = Measured value - PVF
SET
Proportional band (%) range 0.1-3600. If P=OFF, it means ON/OFF control SET
Integral time range 0.1-3600. I=OFF means
4
↓
cancel integral time.
N0
17 18
9 TD7
AL1
means unlocked. LcK=010 means locked.
Note: T1
means autotuning.
T2 G
6 ▲
8
+
6
SSR
7
-
13
2
14
3
15
4
16
5
17
6
18
7
19
8
20
N0
OUT1
Mamual/Auto Convertion: In display estate,press <
com
1
NC
+ 6
B For the very first time, please press SET and <
←
↑
↑←
↑←
↑←
HY
SET
Terminal configurations (If any changed, please refer to the product showing.) B 1 7
cancel derivative time.
↓ SET
90～260V/AC
Control directions: HEAt: heating COOL: cooling Control hysteresis, range: ± 100. It is not available when P ≠ OFF
2
SSR 0UT1 4 RELAY 4
AL1
The output control mode ,RELAY=020, SSR\SCR=001,4-20mA=000.
3 +
3
4-20 mA
↓ SET
SET
8
Parameter lock code setting. LcK=000
Derivative time range 0.1-3600. D=OFF means
↓
RELAY N C
↓
TC/m V
↓
16
↑
SET
Input signal selection TC: K, J, E, S RTD: Pt100, Cu50 The factory setting is K
↓
G
15
7
OUT1
SET
TD4
5 6
+
SSR
-
← ←
↓
T2
7 9
6
90-260V AC
↑
↓
▲
B
+
RTD
2:Absolute value HI alarm
LO ▲
HY ↑←
O N 3: Absolute value LO alarm
8
LO
△
O N
A
△
B
+ 11
11 AL2
12
5: Section inside alarm
12
SSR
-
OFF
▲
ON
HI
OFF ▲
HI
O N
OFF
4: Section outside alarm
9 10
△
△
HI OFF
△ ▲ △ HI Note: All the factory setting value of deviation alarm is 1.0.
FUSE
R J C
1 2 3 4 5 6 7 8 9
Power supply
OUT1
10 11 12 13 14 15 16
NC NO
17 18
Pt
AL1
J-1
Heating cord
SET
T1
5
13 14
1.Relay output control (forTA9)
equipment
↓
-
7 8
12
B
Heating
①
=tPV 4-20mA,
F means F degree.
SET AL1 mode: 0: Deviation HI alarm 1: Deviatian
AL2 set range: –1999-9999.
=PID,control; transmit;
Temperature unit. C means C degree,
AL1 set range: –1999-9999
↓ SET
SSR
4 RELAY
4
RTD
11
RTD
↓SET
HOLD SET ＞3 S
alarm 5: Section inside alarm 6: TC broken alarm ,The factory setting is 2
+ Only for 4-20mA
------------------------------------------
LO alarm 2: Absolute value HI alarm 3: Absolute value LO alarm 4: Section outside
-
SET
3 AL1
Application examples
A
90-260V DC/AC
↓
SSR
4-20mA
0: No decimal 1: One decimal
(when analogue is active)
3
OUT2/AL2
High analogue output
Password setting. Factory setting 015
↓
+
TC
-
↓SET
↓
2
↓ SET Decimal point setting:
10
90-260V AC/DC
← ←
↓SET
1
High analogue output (when analogue is active)
+
AL2 hysteresis setting value. Range ± 90, factory setting 1.0
Malfunction estimate ① No Display : Check all the connection and wiring if it is all correct. Specially pay attention to the power supply terminals and signal input ternimals. ② Incorrect Didplay: Check if the input signal is conformity with the selected symbol. For TC input, please use the relative compensation cable. For RTD input, please use low impedence cable. The 3 wires should at the same length. If all above mentioned is collect , pleaase use parameter PVF to modify. ③ Incorrect Control : If the instrument has been used for a long time, the user find the temperature is hard to rise up to the set value, meanwhile the outsidesystem running well, there must be something wrong with the parameters of the instrument. The user need to re-autotuning the instrument. If the instrument lost control, please check if the connection of the control is correct. If external load is shorted, broken, wrong connection or components is damaged, it will cause lost control as well. When it is necessary, please push out the PCB to check the if the output terminals is damaged and not available. ④ Display malfunction : “UUUU”: The input signal exeed the measured HI range .
2
