TABLE OF CONTENTS SFS-01 Leading Edge Termination Detail for Self-Leveling and Laminate Flooring Systems SFS-02 Leading Edge Termination Detail for Mortar Flooring Systems SFS-03 Termination Detail for Mortar at Nose Angle Iron at Loading Dock or Building Joint SFS-04 Termination Detail at Nose Angle Iron at Stair Tread or Building Joint
DETAILS GUIDE STRATASHIELD STANDARD FLOORING
SFS-05 Control Joint Treatment Detail with No Potential Movement SFS-06 Control Joint Treatment Detail with Potential Movement SFS-07 Expansion/Isolation Joint Treatment Detail SFS-08 Treatment for Non-Moving Crack Treatment Detail SFS-09 Treatment for Moving Crack Treatment Detail SFS-10 Treatment for Bridging Multiple Non-Moving Hairline Cracks SFS-11 Cant Cove Detail SFS-12 Spoon Cove Detail SFS-13 Rolled Radius Cove SFS-14 Rolled Radius Cove Detail Eliminating Top Edge SFS-15 Cove Detail for Flush Transition FRP SFS-16 Cove Detail for Flush Transition Tile SFS-17 Expansion/Isolation Joint Treatment Detail at Wall/ Floor Interface for Laminate and Mortar Systems without cove SFS-18 Expansion/Isolation Joint Treatment Detail at Wall/ Floor Interface for Laminate and Mortar Systems with cove SFS-19 Expansion/Isolation Joint Treatment Detail at Wall/ Floor Interface for Laminate and Mortar Systems with cove
TNEMEC COMPANY INCORPORATED 6800 Corporate Drive, Kansas City, MO 64120 1-800-TNEMEC1 www.tnemec.com
SFS-20 Expansion/Isolation Joint Treatment Detail at Wall/ Floor Interface for Laminate and Mortar Systems with cove SFS-21 Floor Drain Detail without Sealant SFS-22 Floor Drain Detail with Sealant
Published techincal data, instructions, and pricing are subject to change without notice. Contact your Tnemec technical representative for current technical data, instructions, and pricing. Warranty information: The service life of Tnemec’s coatings will vary. For warranty, limitation of seller’s liability, and product information, please refer to Tnemec’s Product Data Sheets at www.tnemec.com or contact your Tnemec Technical Representative. 6/2014
SFS-23 Sleeved or Non-Sleeved Pipe Penetration in Floor Detail
TABLE OF CONTENTS
Rolled Radius Cove Detail..............................................................SFS-13 Rolled Radius Cove Detail Eliminating Top Edge...............................SFS-14 Cove Detail for Flush Transition FRP................................................SFS-15 Cove Detail for Flush Transition Tile................................................SFS-16 Expansion/Isolation Joint Treatment Detail at Wall/Floor Interface for Laminate and Mortar Systems without cove.....................................SFS-17 Expansion/Isolation Joint Treatment Detail at Wall/Floor Interface for Laminate and Mortar Systems with cove.........................................SFS-18 Expansion/Isolation Joint Treatment Detail at Wall/Floor Interface for Laminate and Mortar Systems with cove.........................................SFS-19 Expansion/Isolation Joint Treatment Detail at Wall/Floor Interface for Laminate and Mortar Systems with cove.........................................SFS-20 Floor Drain Detail without Sealant.................................................SFS-21 Floor Drain Detail with Sealant......................................................SFS-22 Sleeved or Non-Sleeved Pipe Penetration in Floor Detail..................SFS-23
STRATASHIELD FLOORING SYSTEM
1/4" WIDE (6.35mm) 1/4" DEEP (6.35mm)
SAWCUT TERMINATION 1/4” (6.35mm) DEEP
EXISTING CONCRETE SUBSTRATE
TNEMEC STR ATASHIELD STANDARD FLOORING DETAILS LEADING EDGE TERMINATION DETAIL FOR SELF-LEVELING AND LAMINATE FLOORING SYSTEMS
NO. SFS - 01
REV.0
CHIP CONCRETE BACK A MINIMUM OF 3”(76.2mm) FOR TRANSITION WITH A 1/2” (12.7mm) DEPTH. MINIMUM 3" (76.2mm) STRATASHIELD FLOORING SYSTEM
1/2" (12.7mm) DEEP SAWCUT
SAWCUT TERMINATION 1/2” (12.7mm) DEEP EXISTING CONCRETE SUBSTRATE
TNEMEC STR ATASHIELD STANDARD FLOORING DETAILS LEADING EDGE TERMINATION DETAIL FOR MORTAR FLOORING SYSTEMS
NO. SFS - 02
REV.0
CHIP CONCRETE BACK A MINIMUM OF 3”(76.2mm) FOR TRANSITION WITH A 1/2” (12.7mm) DEPTH. EMBEDDED NOSING ANGLE IRON
MINIMUM 3" (76.2mm) STRATASHIELD FLOORING SYSTEM
1/2" (12.7mm) SAWCUT
EXISTING CONCRETE SUBSTRATE
TNEMEC STR ATASHIELD STANDARD FLOORING DETAILS TERMINATION DETAIL FOR MORTAR AT NOSE ANGLE IRON AT LOADING DOCK OR BUILDING JOINT
NO. SFS - 03
REV.0
TREAD NOSING
STRATASHIELD FLOORING SYSTEM
THICKNESS AS SPECIFIED
EXISTING CONCRETE SUBSTRATE
TNEMEC STR ATASHIELD STANDARD FLOORING DETAILS TERMINATION DETAIL AT NOSE ANGLE IRON AT STAIR TREAD OR BUILDING JOINT
NO. SFS - 4
REV.0
STRATASHIELD FLOORING SYSTEM
FILLER MATERIAL
EXISTING CONCRETE SUBSTRATE
NOTE: USE SERIES 215 OR STRATASHIELD 100% SOLIDS EPOXY MIXED WITH FUMED SILICA, SILICA FLOUR OR FINE AGGREGATE FOR FILLER MATERIAL
TNEMEC STR ATASHIELD STANDARD FLOORING DETAILS CONTROL JOINT WITH NO POTENTIAL MOVEMENT
NO. SFS - 5
REV.0
STRATASHIELD FLOORING SYSTEM
FLEXIBLE JOINT SEALANT
1/2" (12.7mm) DEEP SAWCUT
EXISTING CONCRETE SUBSTRATE
NOTE: FLEXIBLE JOINT SEALANT WIDTH TO DEPTH RATIO SHOWN IS APPROXIMATELY 2:1. DETAIL CAN BE BUILT BY INSTALLING FLOOR SYSTEM OVER JOINT, RESAWCUTTING, AND INSTALLING SEALANT.
TNEMEC STR ATASHIELD STANDARD FLOORING DETAILS CONTROL JOINT WITH POTENTIAL MOVEMENT
NO. SFS - 06
REV.0
BACKER ROD AND FLEXIBLE JOINT SEALANT
STRATASHIELD FLOORING SYSTEM
EXISTING CONCRETE SUBSTRATE
1/2" (12.7mm) 1/4" (6.35mm)
EXISTING EXPANSION/ ISOLATION JOINT MATERIAL
NOTE: FLEXIBLE JOINT SEALANT WIDTH TO DEPTH RATIO SHOWN IS APPROXIMATELY 2:1. DETAIL CAN BE BUILT BY INSTALLING FLOOR SYSTEM OVER JOINT, RESAWCUTTING, AND INSTALLING BACKER ROD AND SEALANT.
TNEMEC STR ATASHIELD STANDARD FLOORING DETAILS EXPANSION/ISOLATION JOINT TREATMENT DETAIL
NO. SFS - 07
REV.0
PATCH WITH FILLER MATERIAL PRIOR TO INSTALLING STRATASHIELD FLOORING SYSTEM STRATASHIELD FLOORING SYSTEM
EXISTING CONCRETE SUBSTRATE
NOTE: USE SERIES 215 OR STRATASHIELD 100% SOLIDS EPOXY MIXED WITH FUMED SILICA OR SILICA FLOUR FOR FILLER MATERIAL. ROUTE OUT CRACK PRIOR TO PATCHING IF CRACK IS LARGER THAN 1/16” (1.58mm).
TNEMEC STR ATASHIELD STANDARD FLOORING DETAILS TREATMENT FOR NON-MOVING CRACKS
NO. SFS - 08
REV.0
FLEXIBLE JOINT SEALANT
ROUTE OUT EXISTING CRACK AND PATCH WITH FILLER MATERIAL PRIOR TO INSTALLING STRATASHIELD FLOORING SYSTEM
STRATASHIELD FLOORING SYSTEM
EXISTING CONCRETE SUBSTRATE
NOTE: USE SERIES 215 OR STRATASHIELD 100% SOLIDS EPOXY MIX WITH FUMED SILICA, SILICA FLOUR OR FINE AGGREGATE FOR FILLER MATERIAL FLEXIBLE JOINT SEALANT WIDTH TO DEPTH RATIO SHOWN IS APPROXIMATELY 2:1. DETAIL CAN BE BUILT BY INSTALLING FLOOR SYSTEM OVER CRACK, RESAWCUTTING, AND INSTALLING SEALANT.
TNEMEC STR ATASHIELD STANDARD FLOORING DETAILS TREATMENT FOR MOVING CRACKS
NO. SFS - 09
REV.0
SERIES 206 FLEXIBLE UNDERLAYMENT 30-40 MILS
STRATASHIELD FLOORING SYSTEM
HAIRLINE CRACKS
EXISTING CONCRETE SUBSTRATE
NOTE: USE FLEXIBLE UNDERLAYMENT TO BRIDGE HAIRLINE CRACKS IN FLOORS WHERE NO EVIDENCE OF SETTLEMENT OR MOVEMENT AND WHERE FLOOR IS NOT EXPOSED TO DRASTIC THERMAL CHANGE.
TNEMEC STR ATASHIELD STANDARD FLOORING DETAILS TREATMENT FOR BRIDGING MULTIPLE NON-MOVING HAIRLINE CRACKS
NO. SFS - 10
REV.0
CONCRETE, CMU, WALL BOARD, ETC.
45 DEGREE CANT COVE
1" - 2" HEIGHT (25.4mm - 50.8mm)
STRATASHIELD FLOORING SYSTEM
EXISTING CONCRETE SUBSTRATE
NOTE: USE DRY MIXED TROWELABLE MORTAR VERSION OF FLOORING MATERIAL TO BUILD COVE.
TNEMEC STR ATASHIELD STANDARD FLOORING DETAILS CANT COVE DETAIL
NO. SFS -11
REV.0
CONCRETE, CMU, WALL BOARD, ETC.
SPOON COVE
COVE HEIGHT 3/4”-1” (19mm-25mm)
STRATASHIELD FLOORING SYSTEM
EXISTING CONCRETE SUBSTRATE
NOTE: USE DRY TROWELABLE MORTAR VERSION OF FLOORING MATERIAL TO BUILD COVE.
TNEMEC STR ATASHIELD STANDARD FLOORING DETAILS SPOON COVE DETAIL
NO. SFS - 12
REV.0
CONCRETE, CMU, WALL BOARD, ETC.
METAL OR PLASTIC COVE STRIP (OPTIONAL)
ROLLED RADIUS COVE COVE HEIGHT 4”-6” (100mm-150mm) STRATASHIELD FLOORING SYSTEM
EXISTING CONCRETE SUBSTRATE
NOTE: USE DRY MIXED TROWELABLE MORTAR VERSION OF FLOORING MATERIAL TO BUILD COVE.
TNEMEC STR ATASHIELD STANDARD FLOORING DETAILS ROLLED RADIUS COVE DETAIL
NO. SFS - 13
REV.0
CONCRETE, CMU, WALL BOARD, ETC.
SERIES 215 SURFACING EPOXY METAL OR PLASTIC COVE STRIP
COVE HEIGHT 4”-6” (100mm-150mm)
ROLLED RADIUS COVE STRATASHIELD FLOORING SYSTEM
EXISTING CONCRETE SUBSTRATE
NOTE: USE DRY MIXED TROWELABLE MORTAR VERSION OF FLOORING MATERIAL TO BUILD COVE.
TNEMEC STR ATASHIELD STANDARD FLOORING DETAILS ROLLED RADIUS COVE DETAIL ELIMINATING TOP EDGE
NO. SFS - 14
REV.0
FRP PANEL
CONCRETE, CMU, WALL BOARD, ETC.
FRP TRIM STRIP
COVE HEIGHT 4”-6” (100mm-150mm)
ROLLED RADIUS COVE STRATASHIELD FLOORING SYSTEM
EXISTING CONCRETE SUBSTRATE
NOTE: USE DRY MIXED TROWELABLE MORTAR VERSION OF FLOORING MATERIAL TO BUILD COVE AND BASE.
TNEMEC STR ATASHIELD STANDARD FLOORING DETAILS COVE DETAIL FOR FLUSH TRANSITION FRP
NO. SFS - 15
REV.0
CONCRETE, CMU, WALL BOARD, ETC.
COVE HEIGHT 4”-6” (100mm-150mm)
TILE
ROLLED RADIUS COVE STRATASHIELD FLOORING SYSTEM
EXISTING CONCRETE SUBSTRATE
NOTE: USE DRY MIXED TROWELABLE MORTAR VERSION OF FLOORING MATERIAL TO BUILD COVE AND BASE.
TNEMEC STR ATASHIELD STANDARD FLOORING DETAILS COVE DETAIL FOR FLUSH TRANSITION TILE
NO. SFS - 16
REV.0
CONCRETE, CMU, WALL BOARD, ETC.
BACKER ROD AND FLEXIBLE JOINT SEALANT STRATASHIELD FLOORING SYSTEM
EXISTING EXPANSION / ISOLATION
EXISTING CONCRETE SUBSTRATE
TNEMEC STR ATASHIELD STANDARD FLOORING DETAILS EXPANSION/ISOLATION JOINT TREATMENT AT WALL/FLOOR INTERFACE FOR LAMINATE AND MORTAR SYSTEMS WITHOUT COVE
NO. SFS - 17
REV.0
METAL OR PLASTIC COVE STRIP (OPTIONAL) CONCRETE, CMU, WALL BOARD, ETC.
*BOND BREAKER
EXISTING EXPANSION / ISOLATION
STRATASHIELD FLOOR TOPPING SAW CUT AND FILL WITH FLEXIBLE SEALANT
POLYETHYLENE BACKER ROD EXISTING CONCRETE SUBSTRATE
NOTE: *BOND BREAKER - EXCEED RECOAT WINDOW ON PRIMER 201, 222, 237, ETC. OR USE DUCT TAPE
TNEMEC STR ATASHIELD STANDARD FLOORING DETAILS EXPANSION/ISOLATION JOINT TREATMENT AT WALL/FLOOR INTERFACE FOR LAMINATE AND MORTAR SYSTEMS WITH COVE
NO. SFS - 18
REV.0
CONCRETE, CMU, WALL BOARD, ETC. METAL OR PLASTIC COVE STRIP (OPTIONAL)
STRATASHIELD FLOOR TOPPING SAW CUT AND FILL WITH FLEXIBLE SEALANT
EXISTING CONCRETE SUBSTRATE
EXISTING EXPANSION / ISOLATION
KEY IN WITH STRATASHIELD TOPPING 1/4” (6.35mm) TO 1/2”(12.7mm) DEEP
POLYETHYLENE BACKER ROD (OPTIONAL)
TNEMEC STR ATASHIELD STANDARD FLOORING DETAILS EXPANSION/ISOLATION JOINT TREATMENT AT WALL/FLOOR INTERFACE FOR LAMINATE AND MORTAR SYSTEMS WITH COVE
NO. SFS - 19
REV.0
CONCRETE, CMU, WALL BOARD, ETC. METAL OR PLASTIC COVE STRIP (OPTIONAL)
STRATASHIELD FLOOR TOPPING METAL OR PLASTIC TERMINATION STRIP
EXISTING CONCRETE SUBSTRATE
EXISTING EXPANSION / ISOLATION
KEY IN WITH STRATASHIELD FLOOR TOPPING 1/4” (6.35mm) TO 1/2”(12.7mm) DEEP POLYETHYLENE BACKER ROD (OPTIONAL)
TNEMEC STR ATASHIELD STANDARD FLOORING DETAILS EXPANSION/ISOLATION JOINT TREATMENT AT WALL/FLOOR INTERFACE FOR LAMINATE AND MORTAR SYSTEMS WITH COVE
NO. SFS - 20
REV.0
CAST-IN-PLACE CIRCULAR FLOOR DRAIN
CHIP CONCRETE BACK A MINIMUM OF 3”(76.2mm) FOR TRANSITION WITH A 1/2” (12.7mm) DEPTH.
MIN. 3" (76.2mm) STRATASHIELD FLOORING SYSTEM
EXISTING CONCRETE SUBSTRATE
TNEMEC STR ATASHIELD STANDARD FLOORING DETAILS FLOOR DRAIN DETAIL WITHOUT SEALANT
NO. SFS - 21
REV.0
CAST-IN-PLACE CIRCULAR FLOOR DRAIN
CHIP CONCRETE BACK A MINIMUM OF 3”(76.2mm) FOR TRANSITION WITH A 1/2” (12.7mm) DEPTH.
MIN. 3" (76.2mm) STRATASHIELD FLOORING SYSTEM
FLEXIBLE JOINT SEALANT EXISTING CONCRETE SUBSTRATE
TNEMEC STR ATASHIELD STANDARD FLOORING DETAILS FLOOR DRAIN DETAIL WITH SEALANT
NO. SFS - 22
REV.0
EXISTING PIPE OR SLEEVE
1” - 2” (25.4mm - 50.5mm) HEIGHT
FLEXIBLE JOINT FILLER STRATASHIELD FLOORING SYSTEM
BACKER ROD
EXISTING CONCRETE SUBSTRATE
TNEMEC STR ATASHIELD STANDARD FLOORING DETAILS SLEEVED OR NON-SLEEVED PIPE PENETRATION IN FLOOR DETAIL
NO. SFS - 23
REV.0
