Syllabus B.Tech. (Electrical & Electronics Engineering), 3rd semester

Syllabus B.Tech. (Electrical & Electronics Engineering), 3rd semester 3EX1A: ELECTRONIC DEVICES & CIRCUITS (Common to EE, EX, EC and EI) B.Tech. ( Electrical & Electronics ) 3rd Semester Max. Marks: 80 3L+1T Exam Hours: 3 CONTACT UNIT CONTENTS HOURS 1 Semiconductor Physics: Mobility and conductivity, charge densities in a semiconductor, Fermi Dirac distribution, Fermi-Dirac statistics and Boltzmann 5 approximation to the Fermi-Dirac statistics, carrier concentrations and Fermi levels in semiconductor. Generation and recombination of charges, diffusion and continuity equation, transport 3 equations, Mass action Law, Hall effect. 2 Junction Diodes: Formation of homogenous and hetrojunction diodes and their energy band diagrams, calculation of contact potential and depletion width, V-I 4 characteristics, Small signal models of diode, Diode as a circuit element, diode parameters and load line concept, C-V characteristics and dopant profile. Applications of diodes in rectifier, clipping, clamping circuits and voltage multipliers.Transient behavior of PN diode.Breakdown diodes, Schottky diodes, and 4 Zener diode as voltage regulator.Construction, characteristics and operating principle of UJT. 3 Transistors: Characteristics, Current Components, Current Gains: alpha and beta. Variation of transistor parameter with temperature and current level, Operating point, 4 Hybrid model, DC model of transistor, h-parameter equivalent circuits.CE, CB and CC configuration. DC and AC analysis of single stage CE, CC (Emitter follower) and CB amplifiers AC & DC load line, Ebers-Moll model.Biasing & stabilization techniques.Thermal 4 runaway, Thermal stability. JFET & MOSFET:Construction and operationofJFET & MOSFET, noise 4 4 performances of FET, parasitic of MOSFET, small signal models of JFET & MOSFET. Biasing of JFET's & MOSFET’s. Low frequency single stage CS and CD (source 4 follower) JFET amplifiers.FET as voltage variable resistor and active load. 5 Small Signal Amplifiers at Low Frequency: Analysis of BJT and FET multistage 4 amplifier, DC and RC coupled amplifiers. Frequency response of single and multistage amplifier, mid-band gain, gains at low and high frequency. Analysis of DC and differential amplifiers, Miller's Theorem, use of Miller and 4 bootstrap configuration.Cascade and cascade configuration of multistage amplifiers (CE-CE, CE-CB, CS-CS and CS-CD), Darlington pair. Text Books S. No. Name of authors’/books/publisher 1 2

Millman Halkias, Integrated Electronics, TMH R. L. Boylestad, Louis Nashelsky, Electronic devices & circuits theory, Pearson Education

Reference Books S. No. Name of authors’/books/publisher 1 2 3 4 5 6 7

David Bell, Electronic Devices & Circuits, Oxford Publications Schultz, Grob’s Basic Electronics, TMH Millman, Electronics Devices and Circuits, ed. 3, TMH Cathey, Electronics Devices and Circuits, ed. 3, TMH J. Millman and A. Grabel, Microelectronics, McGraw Hill, International B.G. Streetman, Solid State Electronic Devices, Prentice Hall of India, New Delhi A. S. Sedra and K. C. Smith, Microelectronic Circuits, Saunder's College, Publishing

Year of pub. 2011 2009

Year of pub. 2009 2007 2006 2005 1999 2002 2014

8

Salivahnan, Electronics Devices and Circuits, ed. 3, TMH

2011

3EX2A: CIRCUIT ANALYSIS & SYNTHESIS B. Tech. (Electrical & Electronics) 3rd Semester 3L UNIT CONTENTS 1

2

3

4

5

Max. Marks: 80 Exam Hours: 3 CONTACT HOURS Network Theorems and Elements:Thevenin’s, Norton’s, Reciprocity, Superposition, 3 Compensation, Miller’s, Tellegen’s and maximum power transfer theorems. Networks with dependent sources.Inductively coupled circuits – mutual inductance, 5 coefficient of coupling and mutual inductance between portions of same circuits and between parallel branches. Transformer equivalent, inductively and conductively coupled circuits Transients Analysis: Impulse, step, ramp and sinusoidal response analysis of first 4 order and second order circuits. Time domain & transform domain (frequency, Laplace) analysis. Initial and final value theorems.Complex periodic waves and their analysis by Fourier 4 analysis.Different kind of symmetry.Power in a circuit. Network Functions: Terminals and terminal pairs, driving point impedance transfer 4 functions. Poles and zeros.Restrictions on pole and zero location in s-plane. Time domain behavior from pole and zero plot. Procedure for finding network 4 functions for general two terminal pair networks. Stability & causality.Hurwitz polynomial, positive real function. Two Port Networks: Two Port General Networks: Two port parameters (impedance, 5 admittance, hybrid, ABCD and S parameters) and their inter relations. Equivalence of two ports.Transformer equivalent, interconnection of two port 3 networks.The ladder network, image impedance, image transfer function, application to L-C network, attenuation and phase shift in symmetrical T and pi networks. Network Synthesis: The four-reactance function forms, specification for reactance 4 function. Foster form of reactance networks. Cauer form of reactance networks Synthesis of R-L and R-C and L-C networks in Foster and Cauer forms.

Text Books S. No. Name of authors’/books/publisher 1 2

Sudhakar, Circuits And Networks: Analysis And Synthesis, TMH Network Analysis and Synthesis, Ghosh&Chakrabartewton

Reference Books S. No. Name of authors’/books/publisher

4


Year of pub. 2008

1

Singh, Electrical Networks, TMH

2

Nahvi, Schaum’s Outlines of Electric Circuits (Sie), TMH

2010

3

Donald Neamen, Eelectronic Circuits: Analysis and Design (Sie), TMH

2006

4

Suresh Kumar, Electric Circuits & Networks, Pearson

5

Nilsson, Electric Circuits, Pearson

2010

6

Decarlo, Linear Circuits Analysis, Oxford

2007

7

Ramakalyan, Linear Circuits (Includes Cd), Oxford

2004

8

Sukhija, Circuits and Network: Analysis, Design, and Synthesis, Oxford

2010

3EX3A: DIGITAL ELECTRONICS (Common to EE, EX, EC, EIC, CS and IT) B.Tech. (Electrical & Electronics) 3rd Semester Max. Marks: 80 3L+1T Exam Hours: 3 UNIT CONTENTS CONTACT HOURS 1 Number Systems, Basic Logic Gates & Boolean Algebra: Binary Arithmetic & Radix representation of different numbers. Sign & magnitude representation, Fixed 3 point representation, complement notation, various codes & arithmetic in different codes & their inter conversion. Features of logic algebra, postulates of Boolean algebra.Theorems of Boolean algebra.Boolean function. Derived logic gates: Exclusive-OR, NAND, NOR gates, 5 their block diagrams and truth tables. Logic diagrams from Boolean expressions and vice-versa. Converting logic diagrams to universal logic. Positive, negative and mixed logic.Logic gate conversion. 2 Digital Logic Gate Characteristics: TTL logic gate characteristics: Theory & 4 operation of TTL NAND gate circuitry. Open collector TTL. Three state output logic. TTL subfamilies.MOS & CMOS logic families. Realization of logic gates in RTL, 4 DTL, ECL, C-MOS & MOSFET. Interfacing logic families to one another. 3 Minimization Techniques: Minterm, Maxterm, Karnaugh Map, K map upto 4 4 variables. Simplification of logic functions with K-map. Conversion of truth tables in POS and SOP form. Incomplete specified functions. 4 Variable mapping.Quinn-McKlusky minimization techniques. 4 4 Combinational Systems: Combinational logic circuit design, half and full adder, subtractor. Binary serial and parallel adders.BCD adder.Binary multiplier. Decoder: Binary to Graydecoder, BCD to decimal, BCD to 7-segment decoder. Multiplexer, demultiplexer,encoder.Octal to binary, BCD to excess-3 encoder.Diode 4 switching matrix.Design of logic circuits by multiplexers, encoders, decoders and demultiplexers. 5 Sequential Systems: Latches, flip-flops, R-S, D, J-K, Master Slave flip flops. 4 Conversions of flip-flops. Counters: Synchronous & asynchronous ripple and decade counters, Modulus counter, skipping state counter, counter design, state diagrams and state reduction 4 techniques. Ring counter. Counter applications. Registers: buffer register, shift register. Text Books S. No. Name of authors’/books/publisher 1

Herbert Taub, Donald L. Schilling, Digital Integrated Electronics, TMH

2

M. Morris Mano, Digital Logic and Computer Design, Pearson Edu.



Year of pub. 2009

1

Millman Taub, Pulse Switching and Network, TMH

2

A. Anandkumar, Fundamentals of Digital circuits, PHI

2009

3

Floyd, Digital Funadamentals, Pearson

2008

4

S. Salivahanan, Sarivazhagan, Digital circuit design, Vikas publications

2009

5

Leach, Digital Principles and Applications, ed. 7, TMH

2008

6

Mandal, Digital Electronics: Principles and Applications, TMH

2009

3EX4A: OBJECT ORIENTED PROGRAMMING (Common to EE, EX, CS and IT) B.Tech. (Electrical & Electronics) 3rd Semester Max. Marks: 80 3L Exam Hours: 3 UNIT CONTENTS CONTACT HOURS 1 Introduction: Review of structures in C, accessing members of structures using 5 structure variables, pointer to structures, passing structures to functions 3 Structures as user defined data types. 2 Introduction to Programming Paradigms: (Process oriented and Object oriented). Concept of object, class, objects as variables of class data type, difference in structures and class in terms of access to members, private and public Basics of C++: Structure of C++ programs, introduction to defining member functions within and 4 outside a class, keyword using, declaring class, creating objects, constructors & destructor functions, Initializing member values with and without use of constructors, simple programs to access & manipulate data members, cin and cout functions. Dangers of returning reference to a private data member, constant objects and members function, composition of classes, friend functions and classes, using this pointer, creating and destroying objects dynamically using new and delete operators. Static class members, container classes and iterators, proxy classes. Members of a 4 class, data & function members. Characteristics of OOP- Data hiding, Encapsulation, data security. 3 Operator Overloading: Fundamentals, Restrictions, operator functions as class 4 members v/s as friend functions. Overloading stream function, binary operators and unary operators.Converting 4 between types. 4 Inheritance: Base classes and derived classes, protected members, relationship between base class and derived classes, constructors and destructors in derived 4 classes, public, private and protected inheritance. Relationship among objects in an inheritance hierarchy, abstract classes, virtual 4 functions and dynamic binding, virtual destructors. 5 Multiple inheritance, virtual base classes, pointers to classes and class members, 8 multiple class members. Templates, exception handling. Text Books S. No. Name of authors’/books/publisher

Year of pub.

1

Dietel, How to Program C++, Pearson

2013

2

K. R. Venugopal, Mastering C++, TMH

1999


Year of pub.

1

Robert Lafore, Object Oriented Programming in C++, Pearson

2001

2

Rambaugh, Object Oriented Design & Modelling, Pearson

2004

3EX5A: ELECTRICAL MACHINES-I (Common to EE and EX) B.Tech. (Electrical & Electronics) 3rd Semester 3L+1T UNIT CONTENTS 1

2

3

4

5

Max. Marks: 80 Exam Hours: 3 CONTACT HOURS (i)Magnetic circuits:Magnetic circuits, magneto motive force magnetic field strength, 5 permeability, reluctance, analogy between electric and magnetic-circuits, B-H curve, hysteresis, series and parallel magnetic circuits, practical magnetic circuits, permanent magnet and their applications. (ii)Electromechanical energy conversion: Basic principles, conservation of energy, 3 physical phenomenon involved in conversion, energy balance, energy stored in magnetic field. DC Generators: Introduction, construction, types, emf equation, lap and wave 4 windings, armature reaction, commutation, methods of improving commutation, equalizer rings. Demagnetizing and cross magnetizing ampere turns, various characteristics of shunt, 4 series and compound generators, voltage build up, losses and efficiency, condition for maximum efficiency. DC Motors: Introduction, principals, back-emf, torque of motor, types, characteristics 4 of shunt, series and compound motors, speed control (field and armature control methods), basic idea of solid state devices in controlling of DC motors. Starting of DC motors, three point and four point starters, losses and efficiency, testing 4 (brake test and swimburnes test), electric braking of DC motors, Applications. Transformer: Construction, Principal, Types, emf equation, no load and short circuit 4 test, equivalent circuits, back-to-back (Sumpner’s test), phasor diagram, Voltage regulation. Efficiency, Condition for maximum efficiency, all day efficiency, parallel operation , 4 auto-transformer, basic idea of welding transformer, current and potential transformer,separation of losses. Polyphase Transformer: Construction,Various connections and groups, choice of 4 connections, open delta connection, Scott connection, three phase to two phase conversion and vice-versa, Applications, Parallel operation and its conditions. Three to six phase conversion.Excitation phenomenon in transformers, magnetizing 4 harmonic currents and their effects,switching currents in transformers, inrush of magnetizing current.Three winding transformer.


A. E. Fitzgerald, C. Kingsley Jr and Umans, Electric Machinery, 6th Edition McGraw Hill, International Student Edition. Kothari & Nagrath, Electric Machines, 3/e, TMH



Year of pub.

1

M. G. Say, The Performance and Design of AC machines, Pit man & Sons.

2003

2

Guru, Electric Machinery, 3e, Oxford

2000

3

R. K. Srivastava, Electrical Machines, Cengage Learning.

2013

4

P. S. Bimbhra, Electrical Machinery, Khanna Pub.

1995

5

Stephen J Chapman, Electric Machinery Fundamentals, McGraw-Hill

2001

6

Husain Ashfaq, Electrical Machines, DhanpatRai& Sons

2013

3EX6A: ADVANCED ENGINEERING MATHEMATICS-I (Common to EE and EX) B.Tech. (Electrical & Electronics) 3rd Semester 3L UNIT CONTENTS 1

2

3

4

5

Max. Marks: 80 Exam Hours: 3 CONTACT HOURS Laplace Transform: Laplace transform with its simple properties, applications to 8 the solution of ordinary and partial differential equations having constant coefficients with special reference to wave and diffusion equations, digital transforms. Fourier Transform: Discrete Fourier transform, Fast Fourier transform, Complex 4 form of Fourier transform and its inverse applications. Fourier transform for the solution of partial differential equations having constant 4 coefficients with special reference to heat equation and wave equation. Fourier Series: Expansion of simple functions in Fourier series, half range series, 5 change of interval, harmonic analysis. Calculus of Variation: Functional, strong and weak variations, simple variation 3 problems, Euler’s equation. Complex Variables: Analytic functions, Cauchy–Riemann equations, Elementary 4 conformal mapping with simple applications. Line integral in complex domain, Cauchy’s theorem, Cauchy’s integral formula. 4 Complex Variables: Taylor’s series, Laurent’s series, poles, Residues. Evaluations 8 of simple definite real integrals using the theorem of residues.Simple contour integration.

Text Books S. No. Name of authors’/books/publisher 1

M. Ray, J. C. Chaturvedi & H.C. Sharma, Differential Equations, Students friends & company

2

Chandrika Prasad, Mathematics for Engineers, Prasad Mudralaya



Year of pub. 2004

1

Bird, Higher Engineering Mathematics, ELSEVIER.

2

Jeffrey, Advanced Engineering Mathematics, ELSEVIER.

2001

3

Chandrika Prasad, Advanced Mathematics for Engineers, Prasad Mudralaya

2006

4

Ervin Kreyzig, Advanced Engineering Maths, Wiley.

2005

3EX7: ELECTRONIC DEVICE LAB (Common to EE, EX, EC and EI) 1.

Study the following devices: (a) Analog & digital multimeters (b) Function/ Signal generators (c) Regulated d. c. power supplies (constant voltage and constant current operations) (d) Study of analog CRO, measurement of time period, amplitude, frequency & phase angle using Lissajous figures.

2.

Plot V-I characteristic of P-N junction diode & calculate cut-in voltage, reverse saturation current and static & dynamic resistances.

3.

Plot V-I characteristic of zener diode and study of zener diode as voltage regulator. Observe the effect of load changes and determine load limits of the voltage regulator.

4.

Plot frequency response curve for single stage amplifier and to determine gain bandwidth product.

5.

Plot drain current - drain voltage and drain current – gate bias characteristics of field effect transistor and measure of Idss&Vp.

6.

Application of Diode as clipper & clamper.

7.

Plot gain- frequency characteristic of two stage RC coupled amplifier & calculate its bandwidth and compare it with theoretical value.

8.

Plot gain- frequency characteristic of emitter follower & find out its input and output resistances.

9.

Plot input and output characteristics of BJT in CB, CC and CE configurations. Find their h-parameters.

10. Study half wave rectifier and effect of filters on wave. Also calculate theoretical & practical ripple factor. 11. Study bridge rectifier and measure the effect of filter network on DC voltage output and ripple factor. 3EX8: CIRCUIT ANALYSIS LAB 1.

Draw the circuit symbols.

2.

Verify theorems for A. C. & D. C. circuits.

3.

PSPICE Programs for Circuit Analysis: DC: Analysis resistor networks to determine node voltages, components voltages, and component currents. b. DC: Analysis of resistor networks that have several voltage and current sources and variable load resistors. c. Transient: Analysis of RC & RL circuits to produce tables of component voltage & current levels for a given set of time instants & to produce graphs of voltages & currents versus time. d. AC: Analysis of impedance networks to determine the magnitude & phase of node voltages, components voltages and component currents. Determine the magnitude & phase and component voltages and currents in resonant circuits & produce voltage and current verses frequency graphs. Programs for Circuit Analysis: a.

4. 5.

a.

6.

Calculate the resistance of a conductor, given its dimensions & resistivity or determine the change in conductor resistance when the temp changes. b. D.C.: Analysis of resistor networks to determine all junction voltages, component voltages, and component currents. c. Transient: Analysis RC & RL circuits to produce tables of component voltage & current levels for a given set of time instants. Convert Y-connected resistor networks to delta-connected circuits.

3EX9: DIGITAL ELECTRONICS LAB (Common to EE, EX, EC, EI, CS and IT) 1.

To verify the truth tables of basic logic gates: AND, OR, NOR, NAND, NOR. Also to verify the truth table of Ex-OR, Ex-NOR (For 2, 3, & 4 inputs using gates with 2, 3, & 4 inputs).

2.

To verify the truth table of OR, AND, NOR, Ex-OR, Ex-NOR realized using NAND & NOR gates.

3.

To realize an SOP and POS expression

4.

To realize Half adder/ Subtractor& Full Adder/ Subtractor using NAND & NOR gates and to verify their truth tables.

5.

To realize a 4-bit ripple adder/ Subtractor using basic Half adder/ Subtractor& basic Full Adder/ Subtractor.

6.

To verify the truth table of 4-to-1 multiplexer and 1-to-4 demultiplexer. Realize the multiplexer using basic gates only. Also to construct and 8-to-1 multiplexer and 1-to-8 demultiplexer using blocks of 4-to-1 multiplexer and 1-to-4 demultiplexer.

7.

Design & Realize a combinational circuit that will accept a 2421 BCD code and drive a TIL -312 sevensegment display.

8.

Using basic logic gates, realize the R-S, J-K and D-flip flops with and without clock signal and verify their truth table

9.

Construct a divide by 2,4& 8 asynchronous counter. Construct a 4-bit binary counter and ring counter for a particular output pattern using D flip flop.

10. Perform input/output operations on parallel in/Parallel out and Serial in/Serial out registers using clock. Also exercise loading only one of multiple values into the register using multiplexer. Note: As far as possible, the experiments shall be performed on bread board. However, Experiment Nos. 1-4 are to be performed on bread board only. 3EX10: C++ PROGRAMMING LAB (Common to EE, EX, CS and IT) 1. 2.

3. 4. 5. 6. 7. 8.

To write a simple program for understanding of C++ program structure without any CLASS declaration. Program may be based on simple input output, understanding of keyword using. Write a C++ program to demonstrate concept of declaration of class with public & private member, constructors, object creation using constructors, access restrictions, defining member functions within and outside a class. Scope resolution operators, accessing an object’s data members and functions through different type of object handle name of object, reference to object, pointer to object, assigning class objects to each other. Program involving multiple classes (without inheritance) to accomplish a task. Demonstrate composition of class. Demonstration Friend function friend classes and this pointer. Demonstration dynamic memory management using new & delete & static class members. Demonstration of restrictions an operator overloading, operator functions as member function and/ or friend function, overloading stream insertion and stream extraction, operators, overloading operators etc. Demonstrator use of protected members, public & private protected classes, multi-level inheritance etc. Demonstrating multiple inheritance, virtual functions, virtual base classes, abstract classes

3EX11: HUMANITIES & SOCIAL SCIENCE (Common to EE and EX) Unit 1 India: Brief history of Indian Constitution, farming features, fundamental rights, duties, directive principles of state. History of Indian National Movement, socio economic growth after independence. Unit 2 Society: Social groups- concept and types, socialization- concept and theory, social control: concept, social problem in contemporary India, status and role. Unit 3 The Fundamentals of Economics: meaning, definition and importance of economics, Logic of choice, central economic problems, positive and normative approaches, economic systems-socialism and capitalism. Unit 4 Microeconomics: Law of demand supply, utility approach, indifference curves, elasticity of demand and supply and applications, consumer surplus, Law of returns to factors and returns to scale. Unit 5 Macroeconomics: concepts relating to National product–National income and its measurement, Simple Keynesian theory, simple multiplier, money and banking. Meaning, concept of international trade, determination of exchange rate, Balance of payments.

Syllabus B.Tech. (Electrical & Electronics Engineering), 4thsemester 4EX1A:ANALOG ELECTRONICS(Common to EE, EX, EC and EI) B. Tech. (Electrical & Electronics) 4th Semester 3L+1T UNIT CONTENTS 1

2

3

4

5

Max. Marks: 80 Exam Hours: 3 CONTACT HOURS 5 Feedback Amplifiers: Classification, Feedback concept, Feedback Topologies, Transfer gain with feedback, General characteristics of negative feedback amplifiers. 3 Analysis of voltage-series, voltage-shunt, current-series and current-shunt feedback amplifier.Stability criterion.Compensation techniques, miller compensation. Oscillators &Multivibrators: Classification. Criterion for oscillation.Tuned 4 collector, Hartley, Colpitts, RC Phase shift, Wien Bridge and crystal oscillators. Astable, monostable and bistablemultivibrators. Schmitt trigger. Blocking 4 oscillators. High Frequency Amplifiers: Hybrid Pi model, conductances and capacitances of 4 hybrid Pi model, high frequency analysis of CE amplifier. Gain bandwidth product, unity gain frequency fT.Emitter follower at high 4 frequencies. Tuned Amplifier:Band Pass Amplifier, Parallel resonant Circuits, Band Width of 4 Parallel resonant circuit. Analysis of Single Tuned Amplifier, Primary & Secondary Tuned Amplifier with BJT & FET. Double Tuned Transformer Coupled Amplifier. Stagger Tuned Amplifier. Pulse 4 Response of such Amplifier. Class C tuned amplifiers, Shunt Peaked Circuits for Increased Bandwidth. Power Amplifiers: Classification, Power transistors & power MOSFET (DMOS, 4 VMOS). Output power, power dissipation and efficiency analysis of Class A, class B, class AB, class C, class D and class E amplifiers as output stages. 4 Pushpull amplifiers with and without transformers. Complementary symmetry & quasi complimentary symmetry amplifiers.


Millman, Integrated Electronics, ed. 2, TMH.

2

A. S. Sedra, Kenneth C. Smith, Microelectronic Circuits, Oxford university press.



Year of pub. 2009

1

M. H. Rashid, Microelectronic Circuits Analysis and design, Cengage Learning.

2

David A. BELL, Electronic Devices and Circuits, Oxford university press.

2009

3

Salivahnan, Electronics Devices and Circuits, ed. 3, TMH.

2011

4EX2: LINEAR INTEGRATED CIRCUITS B. Tech. (Electrical & Electronics) 4th Semester 3L+1T UNIT CONTENTS 1

2

3 4

5

Max. Marks: 80 Exam Hours: 3 CONTACT HOURS Operational Amplifiers: Basic differential amplifier analysis, Single ended and double 5 ended configurations, Op-amp configurations with feedback. Op-amp parameters, Inverting and Non-Inverting configuration, Comparators, Adder. 3 Operational Amplifier Applications: Integrator, Differentiator, Voltage to 4 frequency & Frequency to voltage converters. Oscillators: Phase shift, Wien Bridge, Quadrature, square wave, triangular wave, saw 4 tooth oscillators. Voltage controlled oscillators. Active Filters: Low pass, high pass, band pass and band reject filters, all pass filter. 4 Switched capacitor filter, Butterworth filter design, Chebyshev Filter design. 4 Phase-Locked Loops: Operating Principles of PLL, Linear Model of PLL, Lock range, 4 Capture range, Applications of PLL as FM detector, FSK demodulator. AM detector, Frequency translator, phase shifter, tracking filter, signal 4 synchronizer and frequency synthesizer, Building blocks of PLL, LM565 PLL. Linear IC’s: Four quadrant multiplier & its applications, Basic blocks of linear IC voltage 4 regulators, three terminal voltage regulators, Positive and negative voltage regulators. The 555 timer as astable and monostablemultivibrators. Zero crossing detector, Schmitt 4 trigger.

Text Books S. No. Name of authors’/books/publisher

Year of pub.

1

R. A. Gayakwad - Op-amplifiers & Linear ICs, Pearson Education.

2007

2

J. M. Jacob – Applications & Design with Analog Integrated Circuits, Prentice Hall of India.

2010


Year of pub.

1

Ramakalyan: LINEAR CIRCUITS (Includes CD), Oxford.

2004

2

K. R. Botkar – Integrated Circuits, Khanna Publications.

2011

3

Salivahanan: Linear Integrated Circuits (TMH).

2010

4

S. M. Sze – VLSI Technology, Tata Mc-Graw Hill.

2006

5

D. Nagchoudhary – principles of Microelectronic Technology, Wheeler Publishing.

6

2001

7

Stephen A Campbell – The Science and Engineering of Microelectronic Fabrication, Oxford Hong Xiao – Introduction to Semiconductor Manufacturing, Prentice Hall India.

8

Kang – CMOS circuit design, Tata Mc-Graw Hill.

2003

2012

4EX3A: ELECTRICAL MEASUREMENTS (Common to EE and EX) B. Tech. (Electrical & Electronics) 4th Semester 3L+1T UNIT CONTENTS 1

2

3

4

5

Max. Marks: 80 Exam Hours: 3 CONTACT HOURS Measuring Instruments: Moving coil, moving iron, electrodynamic and induction 5 instruments-construction, operation, torque equation and errors. Applications of instruments for measurement of current, voltage, single-phase power and singlephase energy. Errors in wattmeter and energy meter and their compensation and adjustment. 3 Testing and calibration of single-phase energy meter by phantom loading. Polyphase Metering: Blondel's Theorem for n-phase, p-wire system. Measurement 5 of power and reactive kVA in 3-phase balanced and unbalanced systems: Onewattmeter, two-wattmeter and three-wattmeter methods. 3-phase induction type energy meter. Instrument Transformers: Construction and operation of current and potential transformers. Ratio and phase angle errors and their minimization. Effect of variation of power 3 factor, secondary burden and frequency on errors. Testing of CTs and PTs. Applications of CTs and PTs for the measurement of current, voltage, power and energy. Potentiometers: Construction, operation and standardization of DC 4 potentiometers– slide wire and Crompton potentiometers. Use of potentiometer for measurement of resistance and voltmeter and ammeter calibrations. Volt ratio boxes. Construction, operation and standardization of AC potentiometer 4 – in-phase and quadrature potentiometers. Applications of AC potentiometers. Measurement of Resistances: Classification of resistance. Measurement of 4 medium resistances – ammeter and voltmeter method, substitution method, Wheatstone bridge method. Measurement of low resistances – Potentiometer method and Kelvin's double 4 bridge method. Measurement of high resistance: Price's Guard-wire method. Measurement of earth resistance. AC Bridges: Generalized treatment of four-arm AC bridges. Sources and 4 detectors. Maxwell's bridge, Hay's bridge and Anderson bridge for self-inductance measurement. Heaviside's bridge for mutual inductance measurement. De Sauty Bridge for capacitance measurement. Wien's bridge for capacitance and frequency measurements. Sources of error in 4 bridge measurements and precautions. Screening of bridge components. Wagner earth device.


Year of pub.

1

H. S. Kalsi, Electronic Inst. & Measurement, TMH

2004

2

Morris, Electrical Measurements & Instrumentation, ELSEVIER

1997


Year of pub. 1994

1

Bell, Electronic Instrumentation And Measurement, Oxford

2

W. D. Cooper, Electronic Inst. & Measurement Techniques, Prentice Hall, India.

2004

3

A. K. Sawhney, Electrical & Electronic Measurement & Inst, DhanpatRai& Sons

2002

4

E. W. Golding & F. C. Widdis, Electrical Measurement & Measuring Instrument, A.W. Wheeler Forest K. Harries, Electrical Measurement, Willey Eastern Pvt. Ltd. India.

2004

5

2008

4EX4A: ELECTRICAL ENGINEERING MATERIALS B. Tech. (Electrical & Electronics) 4th Semester 3L UNIT CONTENTS

Max. Marks: 80 Exam Hours: 3 CONTACT HOURS Dielectric Materials: Polarization phenomenon, spontaneous polarization, dielectric 8 constant and loss, piezo and Ferro electricity application. Magnetic Materials: Dia, Para, ferro- ferrimagnetisms; soft and hard magnetic materials and their applications. Semi-Conductor Materials: Crystal growth, zone refining, Degenerate and no 5 degenerate semiconductors, Direct and indirect band gap semiconductors. 3 Electronic properties of silicon, Germanium, Compound Semiconductor, Gallium

1 2 3

Arsenide, gallium phosphide & Silicon carbide. Conductive & Superconductive Materials:Electrical properties of conductive and resistive materials. Important characteristics and electronic applications of specific conductor & resistance materials. Superconductor phenomenon, Type I and Type II superconductors and their applications. Passive Components &PCB Fabrication: Brief study of fabrication methods of fixed and variable type of resistors; capacitors, Inductors, solenoid and toroid, air core, iron core and Ferro core conductors. Printed Circuit Boards - Types, Manufacturing of copper clad laminates, PCB Manufacturing process, Manufacturing of single and double sided PCBs. Surface mount devices - advantages & limitations.

4

5


S. O. Kasap, “Principle of Electrical Engineering materials and devices” , 3/e, TMH B. D. Indu, “Electrical Engineering Materials”, Jain Brothers.

Reference Books S. No. Name of authors’/books/publisher 1 2 3 4 5 6

Robert M Rose, “Structures and Properties of Materials Volume IV”, Electronic Properties, Wiley. S. P. Seth and P. V. Gupta, “A Course of Electrical Engineering Materials”, DhanpatRai& Sons. C. S. Indulkar & S. Thiruvengadam, “An Introduction to Electrical Engineering Materials”, S.Chand. A.J. Dekker, “Electrical Engineering Materials”, Prentice Hall of India. C.S. Indulkar&S.Triruvagdan “An Introduction to Electrical Engg. Materials, S.Chand& Co. Solymar, “Electrical Properties of Materials” Oxford University Press.T. K. Basak, “Electrical Engineering Materials” New age International

5

3 4

4


Year of pub.

1994 2010 2010 2010

4EX5A: ELECTRICAL MACHINES –II (Common to EE and EX) B. Tech. (Electrical & Electronics) 4th Semester 3L+1T UNIT CONTENTS 1

2

3

4

5

Max. Marks: 80 Exam Hours: 3 CONTACT HOURS AC Machines Fundamentals: Introduction, emf equation, mmf of three phase AC 5 winding, production of rotating magnetic field, types of AC windings. Concentric, distributed and chorded windings, pitch factor, distribution factor, 3 effect of these factors on induced emf, effect of harmonics. 5 Polyphase Induction Motor: Introduction. Construction, cage and wound rotors, principal, starting and running torque, condition for maximum torque, equivalent circuits, no load and block rotor test. Torque-slip characteristics, losses and efficiency, circle diagram, starting of cage 3 and wound motors, speed control, cogging and crawling, double cage rotor, induction generator, application. (i) Single Phase Induction Motor:Introduction, construction, principal, double 4 revolving field theory, equivalent circuit, performance calculations, starting methods, and their types, torque slip characteristics of various types. ii) Special Machines: Single phase synchronous motor, series motor, universal 4 motor, Stepper motors variable reluctance, permanent magnet and hybrid stepper motors. 5 Synchronous Generators (Alternators): Introduction, Construction, advantages of rotating field, types of rotors, emf equation, excitation systems, equivalent circuit and their phasor diagrams, voltage regulation, synchronous impedance method, mmf method. Zero power factor method, two reaction theory of salient pole rotor, phasor 3 diagram, power developed and power angle characteristics of salient pole machine, determination of Xd and Xq, synchronization, synchronizing power and torque, parallel operation application. Synchronous Motors:Introduction, construction, principal of operation, starting of 4 synchronous motor, equivalent circuit and phasor diagrams, power and torque, performance calculation, speed torque characteristics, power factor control-effect of change of excitation. V curve and inverted V curve, synchronous condenser and reactors, synchronous 4 phase modifiers, hunting-causes and remedies, applications, synchronous induction motor application.


A. E. Fitzgerald, C. KingsleyJr and Umans, Electric Machinery, 6th Edition McGraw Hill, International Student Edition. Kothari & Nagrath, Electric Machines 3/e,TMH



Year of pub. 2002

1

M. G. Say, The Performance and Design of AC machines, Pit man & Sons.

2

Guru, Electric Machinery 3e, Oxford

2000

3

R. K. Srivastava, Electrical Machines, Cengage Learning.

2010

4

P. S. Bimbhra, Electrical Machinery, Khanna Pub.

1995

5

Stephen J Chapman, Electric Machinery Fundamentals, McGraw-Hill

2001

6

Husain Ashfaq, Electrical Machines, DhanpatRai & Sons

2012

7

Irving L. Kosow, Electric Machine and Tranformers, Prentice Hall of India.

1992

4EX6A: ADVANCED ENGINEERING MATHEMATICS-II (Common to EE and EX) B. Tech. (Electrical & Electronics) 4th Semester Max. Marks: 80 3L Exam Hours: 3 UNIT CONTENTS CONTACT HOURS 1 Numerical Analysis: Finite differences - Forward backward and central difference. 5 Newton’s forward and backward differences interpolation formulae. Sterling’s formulae, Lagrange’s interpolation formula. Solution of non-linear equations in one variable by Newton Raphson and Simultaneous algebraic equation by Gauss and Regula Falsi method. 3 Solution of simultaneous equations by Gauss elimination and Gauss Seidel methods. Fitting of curves (straight line and parabola of second degree) by method of least squares. 2 Numerical Analysis: Numerical differentiation, numerical integration trapezoidal 4 rule, Simpson’s one-third and one eighth rule. Numerical Integration of ordinary differential equations of first order. Picard’s method, Euler’s & modified Euler’s methods. Miline’s method and Runga 4 Kutta fourth order method. Simple linear difference equations with constant coefficients. 3 Special Functions: Bessel’s function of first and second kind, simple recurrence 4 relations, orthogonal property of Bessel functions, Transformation, Generating functions. Legendre’s function of first kind, simple recurrence relations, orthogonal property, 4 Generating functions. 4 Statistics & Probability: Elementary theory of probability, Baye’s theorem with 4 simple applications, Expected value. Theoretical probability distributions – Binomial, Poisson and Normal distributions. 4 5 Statistics & Probability: Lines of regression, co-relation and rank correlation. 4 4 Transforms: Z-transforms, its inverse, simple properties and application to difference equations. Text Books S. No. Name of authors’/books/publisher

Year of pub.

1

Jeffrey, Advanced Engineering Mathematics, ELSEVIER

2006

2

Ervin Kreyzig, Advanced Engineering Maths, John Wiley

2010


Year of pub.

1

Bird, Higher Engineering Mathematics , ELSEVIER

2004

2

Chandrika Prasad, Advanced Mathematics for Engineers, Prasad Mudralaya

2002

3

2008

4

Kaplan, W., Advanced Mathematics for Engineers, Addison-Wesley Publishing Co. Brigham, E.O., The Fast Fourier Transform and its Applications, Prentice-Hall

1988

5

J. N. Kapur, Mathematical Statistics, S. Chand & company Ltd

2000

6

R. K. Jain & S. R. K. Iyenger, Advance Engineering Mathematics, Narosa Pub.

2002

7

E. Kreysig, Advanced Engineering Mathematics, John Wiley & Sons

2005

4EX7A: ANALOG ELECTRONICS LAB (Common to EE, EX, EC and EI) 1.

Plot gain-frequency characteristics of BJT amplifier with and without negative feedback in the emitter circuit and determine bandwidths, gain bandwidth products and gains at 1 kHz with and without negative feedback.

2.

Study of series and shunt voltage regulators and measurement of line and load regulation and ripple factor.

3.

Plot and study the characteristics of small signal amplifier using FET.

4.

Study of push pull amplifier. Measure variation of output power & distortion with load.

5.

Study Wein bridge oscillator and observe the effect of variation in R & C on oscillator frequency.

6.

Study transistor phase shift oscillator and observe the effect of variation in R & C on oscillator frequency and compare with theoretical value.

7.

Study the following oscillators and observe the effect of variation of C on oscillator frequency: (a) Hartley (b) Colpitts.

8.

Design Fabrication and Testing of k-derived filters (LP/HP).

9.

Study of a Digital Storage CRO and store a transient on it.

10. To plot the characteristics of UJT and UJT as relaxation. 11. To plot the characteristics of MOSFET and CMOS.

4EX8A: ELECTRICAL MEASUREMENT LAB (Common to EE and EX) 1.

Study working and applications of (i) C.R.O. (ii) Digital Storage C.R.O. & (ii) C.R.O. Probes.

2.

Study working and applications of Meggar, Tong-tester, P.F. Meter and Phase Shifter.

3.

Measure power and power factor in 3-phase load by (i) Two-wattmeter method and (ii) One-wattmeter method.

4.

Calibrate an ammeter using DC slide wire potentiometer.

5.

Calibrate a voltmeter using Crompton potentiometer.

6.

Measure low resistance by Crompton potentiometer.

7.

Measure Low resistance by Kelvin's double bridge.

8.

Measure earth resistance using fall of potential method.

9.

Calibrate a single-phase energy meter by phantom loading at different power factors.

10. Measure self-inductance using Anderson's bridge. 11. Measure capacitance using De Sauty Bridge 4EX9A: INTEGRATED CIRCUIT LAB 1.

Op-Amp characteristics and get data for input bias current measure the output-offset to zero and calculate slew rate.

2.

Op-Amp in inverting and non-inverting modes.

3.

Op-Amp as scalar, summer and voltage follower.

4.

Op-Amp as differentiator and integrator. Design LPF and HPF using Op-Amp 741

5.

Design Band Pass and Band reject Active filters using Op-Amp 741.

6.

Design Oscillators using Op-Amp (i) RC phase shift (ii) Hartley (iii) Colpitts

7.

Design (i) Astable (ii) Monostablemultivibrators using IC-555 timer

8.

Design Triangular & square wave generator using 555 timer.

voltage and reduce it

9.

Design Amplifier (for given gain) using Bipolar Junction Transistor. 4EX10A: ELECTRICAL MACHINE LAB (Common to EE and EX)

1.

Speed control of D.C. shunt motor by (a) Field current control method & plot the curve for speed verses field current. (b) Armature voltage control method & plot the curve for speed verses armature voltage.

2.

To perform O.C. and S.C. test on a 1-phase transformer and to determine the parameters of its equivalent circuit its voltage regulation and efficiency.

3.

To perform back-to-back test on two identical 1-phase transformers and find their efficiency & parameters of the equivalent circuit.

4.

To determine the efficiency and voltage regulation of a single-phase transformer by direct loading.

5.

To plot the O.C.C. & S.C.C. of an alternator and to determine its Zs, Xd andregulation by synchronous impedance method.

6.

To plot the V-curve for a synchronous motor for different values of loads.

7.

To perform the heat run test on a delta/delta connected 3-phase transformer and determine the parameters for its equivalent circuit.

8.

To perform no load and blocked rotor test on a 3 phase induction motor and to determine the parameters of its equivalent circuits. Draw the circle diagram and compute the following (i) Max. Torque (ii) Current (iii) slips (iv) p.f. (v) Efficiency.

9.

To Plot V-Curve and inverted V-Curve of synchronous motor.

10. To synchronize an alternator across the infinite bus (RSEB) and control load sharing.

4EX11A: ELECTRICAL MACHINE DESIGN (Common to EE and EX) 1.

Design of transformers: output of transformer, output equation- volt per turn, core area and weight of iron & copper, optimum design–(i) minimum cost and (ii) minimum losses. Design of core and windings. Design a 3-phase transformer.

2.

Design of rotating machines: General concepts. specific loading, output equations –dc machines and ac machines, factor affecting size of rotating machines, choice of specific magnetic and electric loadings.

3.

Design of 3-phase induction motors: output equation, choice of air gap flux density and ampere conductors’parameter, main dimensions. Design of a 3-phase squirrel cage induction motor.

4.

Design of single phase induction motors: output equation, main dimensions, relative size of single phase and 3-phase induction motors. Design of a single phase capacitor start induction motor.

5.

Design of synchronous machines: output equation, choice of specific magnetic and electric loadings, main dimensions, short

Syllabus B.Tech. (Electrical & Electronics Engineering), 5thsemester 5EX1A: POWER ELECTRONICS (Common for EE and EX) B. Tech. (Electrical & Electronics) 5th Semester Max. Marks: 80 3L+1T Exam Hours: 3 UNIT 1

2

3

4

5

CONTENTS

CONTENTS

Power Semiconductor Devices:Construction, Principle of operation, Characteristics and applications of Power Transistor& Thyristor. Characteristics of GTO, DIAC, MCT, TRIAC, Power MOSFET and IGBT; TwoTransistor Model of Thyristor, Thyristor Commutation methods. SCR: Construction and characteristics, specification and ratings, pulse transformer, optical isolators, methods of turn on, triggering circuits for SCR: R, RC, UJT relaxation oscillator. Rating extension by series and parallel connections, string efficiency. Protection of SCR-Protection against over voltage, over current, dv/dt, di/dt, Gate protection. Converters-I: Single Phase half & full wave converters with RL & RLE load, Single phase dual converters, Three phase half wave converters. Three phase full converters with RL load, Three phase dual converters. Converters-II: Single and three-phase semi converters with RL & RLE load. Power factor improvement-Extinction angle control, symmetrical angle control, pulse width modulation control and sinusoidal pulse width modulation control. Inversion operation. Effect of load and source impedances. DC-DC Converters: Step Up/Down Copper, Control strategies, Chopper Configurations, Analysis of type A Chopper Voltage, current and load commutated chopper. Multiphase Chopper

3


M. D. Singh and K. B. Khanchandani: Power Electronics 2/e, MGH, 2008.

2

M. H. Rashid: Power Electronics, Circuits Devices and Applications, Pearson.

Reference Books S. No. Name of authors’/books/publisher 1

5 4

4 5 3 6

2 4 4

Year of Pub. 2008 2011

Year of Pub. 2005

2

V. R. Moorthi: Power Electronics-Devices, Circuits and Industrial Applications, Oxford. Theodore Wildi: Electrical Machines, Drives and Power Systems, Pearson.

3

Ned Mohan: Power Electronics, John Wiley.

2013

4

Krein P. T.: Elements of Power Electronics, Oxford.

1998

5

P. S. Bimbhra: Power Electronics, Khanna Publishers.

2012

2007

5EX2A: ANALOG COMMUNICATION B. Tech. (Electrical & Electronics) 5th Semester 3L UNIT CONTENTS

Max. Marks: 80 Exam Hours: 3 CONTACT HOURS Noise Effects in Communication Systems:Resistor noise, Networks with reactive 4 elements, Noise temperature, Noise bandwidth, Effective input noise temperature, Noise figure. Noise figure & equivalent noise 4 temperature in cascaded circuits. Amplitude Modulation: Frequency translation, Recovery of base band signal, 4 Spectrum & power relations in AM systems.Methods of generation & demodulation of AM-DSB, AM-DSB/SC and AM-SSBsignals. Modulation & detector circuits for AM systems. AM transmitters & receivers. 4 Frequency Modulation:Phase & freq. modulation & their relationship, Spectrum & 5 band width of a sinusoidally modulated FM signal, phasor diagram, Narrow band & wide band FM. Generation & demodulation of FM signals. FM transmitters &receivers. Comparison of AM, FM & PM. Pre emphasis & 3 demphasis. Threshold in FM, PLL demodulator. Noisein AMand FM: Calculation of signal-to-noise ratio in SSB-SC, DSBSC, DSB 6 with carrier, Noise calculation of square law demodulator & envelope detector. Calculation of S/N ratio in FM demodulators, Super heterodyne receivers. 2 Pulse Analog Modulation:Practical aspects of sampling: Natural and flat top 8 sampling. PAM, PWM, PPM modulation and demodulation methods, PAM-TDM.

1

2

3

4

5


H. Taub & D. L. Schilling: Principles of Communication Systems 3/e, MGH.

2

G. Kennedy: Electronic Communication Systems, 4/e, MGH.


Year of Pub. 2008 1999

Year of Pub. 2009

2

B.P. LATHI: Modern Digital Analog Communication Systems, Oxford University Press. Simon Haykin: Communication Systems, John Wiley & Sons.

3

B. P. Lathi: Communication Systems, John Wiley.

1988

4

Louch: Digital & Analog Communication, Pearson Education.

2011

5

Tomasi: Electronic Communication, Pearson Education.

1994

2008

5EX3A: CONTROL SYSTEMS (Common for EE and EX) B. Tech. (Electrical & Electronics) 5th Semester 3L+1T UNIT CONTENTS 1

2

3

4

5

Max. Marks: 80 Exam Hours: 3 CONTACT HOURS Introduction: Elements of control systems, concept of open loop and closed loop 5 systems, Examples and application of open loop and closed loop systems, brief idea of multivariable control systems Mathematical Modeling of Physical Systems: Representation of physical system 3 (Electro Mechanical) by differential equations, Determination of transfer function by block diagram reduction techniques and signal flow method, Laplace transformation function, inverse Laplace transformation Time Response Analysis of First Order and Second Order System:Characteristic 4 equations, response to step, ramp and parabolic inputs, Transient response analysis, steady state errors and error constants, Transient & steady 4 state analysis of LTI systems Control System Components: Constructional and working concept of ac servomotor, 5 synchronous and stepper motor Stability and Algebraic Criteria: concept of stability and necessary conditions, 3 Routh-Hurwitz criteria and limitations.Root Locus Technique: The root locus concepts, construction of root loci Frequency Response Analysis: Frequency response, correlation between time and 5 frequency responses,polar and inverse polar plots, Bode plots Stability in Frequency Domain: Nyquist stability criterion, assessment of relative 3 stability: gain margin and phase margin, M and N Loci, Nichols chart. The design problem and preliminary considerations lead, lag and lead-lag networks, 4 design of closed loop systems using compensation techniques in time domain and frequency domain. Brief idea of proportional, derivative and integral controllers. 4


Year of Pub.

1

Smarjit Ghosh, Control Systems: Theory and Applications, 2/e, Pearson Publisher.

2004

2

Dhannesh N. Manik: Control System, Cengage Learning.

2012

Reference Books S. No. Name of authors’/books/publisher 1 2

Year of Pub.

I. J. Nagrath and M. Gopal: Control Systems Engineering, 3rd Ed, New Age Publication. K. R. Varmah: Control Systems, MGH th

2008 2010

3

Anandnatrajan et. al.: Control Systems Engineering, 4 ed., Scitech Pub.

2013

4

K. Ogata: Modern Control Engineering, Prentice Hall of India.

2010

5

Norman S. Nise: Control System Engineering, John Wiley & Sons.

2011

6

Richard C. Dorf, Robert H. Bishop: Modern Control Systems, Prentice-Hall

2000

7

Robert H. Bishop: Modern Control Systems, Boyd and Fraser pub

2000

5EX4A: DATA BASE MANGEMENT SYSTEM (Common for EE and EX) B. Tech. (Electrical & Electronics) 5th Semester Max. Marks: 80 3L Exam Hours: 3 UNIT CONTENTS CONTACT HOURS 1 Introduction, need, purpose and goals of DBMS. DBMS Architecture, Concept of 8 keys, Generalization and specialization, introduction to relational data model, ER modeling, concept of ER diagram 2 Database Design: Conceptual Data Base design. Theory of normalization, Primitive 3 and composite data types, concept of physical and logical databases, Dataabstraction and data independence, relational algebra and relational calculus. 5 3 SQL, DDL and DML. Constraints assertions, views database security. Application 5 Development using SQL: Host Language interface embedded SQL programming. GL’s, Forms management and report writers. Stored procedures and triggers. Dynamic 3 SQL, JDBC. 4 Internal of RDBMS: Physical data organization in sequential, indexed, random and 8 hashed files. Inverted and multilist structures. 5 (i) Transaction Management: Transaction concept, transaction state, serializability, 4 conflict serializabiltiy, views serializability. (ii) Concurrency Control: Lock based protocol (iii) Deadlock Handling: Prevention detection, recovery. (iv) Recovery System: Log 4 based recovery. Text Books S. No. Name of authors’/books/publisher

Year of pub.

1

Silverschatz Korth and Sudarshan: Database System Concepts, 6th ed., MGH.

2011

2

Raghu Rama Krishnan: Database Management Systems, 2nd ed., MGH.

2003


Year of pub.

1

S. K Singh: Database System Concepts, Designs and Applications, Pearson Education

2011

2

Elmasari: Fundamentals of Data Base Systems, Pearson Education.

2003

3

G. K. Gupta: Database Management Systems, MGH.

2011

4

Date C. J.: An Introduction To Database System, Addition Wesley.

2003

5

Alex Berson & Stephen J. Smith: Data Warehousing, Data Mining & OLAP, MGH.

2011

6

Mallach: Data Warehousing System, MGH.

2003

7

Majumdar & Bhattacharya: Database Management System, MGH.

2011

5EX5A: TRANSMISSION & DISTRIBUTION OF ELECTRICAL POWER (Common for EE and EX) B. Tech. (Electrical & Electronics) 5th Semester Max. Marks: 80 3L+1T Exam Hours: 3 UNIT CONTENTS CONTACT HOURS 1 Supply Systems:Basic network of power system. Transmission and distribution 5 voltage, effect of system voltage on size of conductor and losses, Comparison of DC 2- wire, DC 3-wire, 1- phase AC and 3- phase AC (3- wire and 4- wire) systems. Distribution Systems:Primary and secondary distribution systems, feeder, distributor 3 and service mains. Radial and ring- main distribution systems. Kelvin’s law for conductor size. 2 Mechanical Features of Overhead Lines:Conductor material and types of conductor. 4 Conductor arrangements and spacing. 4 Calculation of sag and tension, supports at different levels, effect of wind and ice loading, stringing chart and sag template. Conductor vibrations and vibration dampers. 3 Parameters of Transmission Lines:Resistance inductance and capacitance of 4 overheadlines, effect of earth, line transposition. Geometric mean radius and distance. Inductance and capacitance of line with symmetrical and unsymmetrical spacing 4 Inductance and capacitance of double circuit lines. Skin and proximity effects.Equivalent circuits and performance of short and medium transmission lines. 4 Generalized ABCD Line Constants:equivalent circuit and performance of long 6 transmission line. Ferranti effect. Interference with communication circuits. Power flow through atransmission line Corona:Electric stress between parallel conductors. Disruptive critical voltage and 2 visual critical voltage, Factors affecting corona. Corona power loss. Effects of corona. 5 Insulators: Pin, shackle, suspension, post and strain insulators. Voltage distribution 4 acrossan insulator string, grading and methods of improving string efficiency. Underground Cables: Conductor, insulator, sheathing and armoring materials. 4 Types of cables. Insulator resistance and capacitance calculation. Electrostatic stresses and reduction of maximum stresses. Causes of breakdown. Thermal rating of cable. Introduction to oil filled and gas filled cables. Text Books S. No. Name of authors’/books/publisher 1 2

S. Sivanagaraju and S. Satyanarayana: Electric Power Transmission and Distribution, Pearson Publisher. A. S. Pabla: Electric Power Distribution, MGH.



Year of pub.

1

B. R. Gupta: Power System Analysis & Design, S. Chand Publishers.

2008

2

Soni, Gupta and Bhatnagar: A Course in Electrical Power, Dhanpat Rai.

1987

3

C. L. Wadhwa: Electrical Power Systems, New Age.

2009

4

Nagrath Kothari: Modern Power System Analysis, MGH.

2011

5

J. J. Grainger & W. D. Stevenson: Power System Analysis, MGH.

2003

6

Kamaraju: Electrical Power Distribution Systems, MGH.

2009

5EX6.1A: BIOMEDICAL INSTRUMENTATION B. Tech. (Electrical& Electronics) 5th Semester 3L+1T UNIT CONTENTS 1

2

3

4

5

Max. Marks: 80 Exam Hours: 3 CONTACT HOURS Human Body Subsystems:Brief description of neural, muscular, cardiovascular and 4 respiratory systems; their electrical, mechanical and chemical activities. Transducers and Electrodes:Principles and classification of transducers for 4 Biomedical applications, Electrode theory, different types of electrodes, Selection criteria for transducers and electrodes. Biopotentials:Electrical activity of excitable cells, ENG, EMG, ECG, ERG, EEG. 4 Neuron potential. Cardio Vascular System Measurements:Measurement of blood pressure, blood flow, cardiac output, cardiac rate, Heartsounds,Electrocardiograph, phonocardiograph, Plethysmograph, 4 Echocardiograph. Instrumentation for Clinical Laboratory:Measurement of pH valve of blood, ESR 5 measurement, hemoglobin measurement, O2and CO2concentration in blood, GSR measurement. Instrumentation for clinical laboratory: Spectrophotometry, chromatography, Hematology, Measurement of pH value, concentration in blood. Medical Imaging:DiagnosticX-rays, CAT, MRI, thermography, Ultrasonography, 3 medical use of isotopes, endoscopy. Patient Care, Monitoring and Safety Measures:Elements of Intensive care 6 monitoring basic hospital systems and components, physiological effect of electric current shock hazards from electrical equipment, safety measures, Standards & practices. Computer Applications and Biotelemetry:Real time computer applications, data 2 acquisition and processing, remote data recording and management. Therapeutic and Prosthetic Devices:Introduction to cardiac pacemakers, 8 defibrillators, ventilators, muscle stimulators, diathermy, heart lung machine, Hemodialysis, Applications of Laser.


Year of pub.

1

Webster J.G.: Medical Instrumentation, Application and Design, John Wiley and Sons.

2009

2

Jacobson, B. Webster, J.G., Medical and Clinical Engineering, PHI, International.

1967


Year of pub.

1

Cromwell: Biomedical Instrumentation and Measurements, et a1, PHI, International

1980

2

R.S. Khandpur: Handbook of Biomedical Instrumentation, MGH.

2003

3

Carr: Introduction to Biomedical Equipments, Pearson Education.

2001

4

T. Cromwell, F.J. Weibell & F. A. Pfieffer: Biomedical Instrumentation & Measurements, PHI. H.E. Thomas: Handbook of Biomedical Instrumentation and Measurement, Restone Publishing Company.

2005

5

1974

5EX6.2A: PRINCIPLE OF COMMUNICATION SYSTEMS (Common for EE and EX) B. Tech. (Electrical& Electronics) 5th Semester Max. Marks: 80 3L+1T Exam Hours: 3 UNIT CONTENTS CONTACT HOURS 1 Noise Effects in Communication Systems: Resistor noise, Networks with reactive 5 elements, Noise temperature, Noise bandwidth, effective input noise temperature, Noise figure. Noise figure & equivalent noise temperature in cascaded circuits. 3 2 Amplitude Modulation: Frequency translation, Recovery of base band signal, 4 Spectrum & power relations in AM systems. Methods of generation&demodulation of AM-DSB, AMDSB/SC and AM-SSB 4 signals. Modulation & detector circuits for AM systems. AM transmitters & receivers. 3 Frequency Modulation: Phase & freq. modulation & their relationship, Spectrum & 5 bandwidth of a sinusoidally modulated FM signal, phasor diagram, Narrow band & wide band FM. Generation & demodulation of FM signals. FM transmitters & receivers, Comparison of AM, FM & PM. Pre emphasis & de3 emphasis. Threshold in FM, PLL demodulator. 4 Noise in AM and FM: Calculation of signal-to-noise ratio in SSB-SC, DSB6 SC, DSB with carrier, Noise calculation of square law demodulator & envelope detector. Calculation of S/N ratio in FM demodulators, Super-heterodyne receivers. 2 5 Pulse Modulation Systems: Sampling theorem, Generation and demodulation 8 methods of PAM, PWM, PPM. Text Books S. No. Name of authors’/books/publisher 1 2

Year of pub.

John G. Proakis, and Masoud Salehi: Fundamentals of Communication Systems, Pearson Publisher. P. Ramakrishna Rao: Communication Systems, MGH.


2007 2013

Year of pub.

1

V. Chandra Sekar: Communication Systems, Oxford.

2006

2

Taub and Schilling: Principles of Communication Systems 3/e, MGH. th

2008

3

B. P. Lathi: Modern Analog & Digital Communication System, 4 ed., Oxford.

2009

4

Simon Hykin: Communication Systems, John Wiley and Sons.

2008

5

R. P. Singh and S. D. Sapre: Communication System Analog & Digital 2/e, MGH.

2008

6

G. Kennedy and B. Davis: Electronic Communication Systems, MGH.

1993

7

Roy Blake: Wireless Communication Technology, Thomson Asia Pvt. Ltd. Singapore.

2008

5EX6.3A INTRODUCTION TO VLSI (Common for EE and EX) B. Tech. (Electrical & Electronics) 5th Semester Max. Marks: 80 3L+1T Exam Hours: 3 UNIT CONTENTS CONTACT HOURS 1 Introduction to MOS Technology: Basic MOS transistors, Enhancement Mode 8 transistoraction, Depletion Mode transistor action, NMOS and CMOS fabrication. 4 2 Basic Electrical Properties of MOS Circuits:IDS versus VDS relationship, Aspects of threshold voltage, Transistor Trans conductance gm. The NMOS inverter, Pull up to Pull-down ratio for a NMOS Inverter and CMOS 4 Inverter (Bn/Bp), MOS transistor circuit Model, Noise Margin. 3 CMOS Logic Circuits:The inverter, Combinational Logic, NAND Gate NOR gate, 5 Compound Gates, 2 input CMOS Multiplexer, Memory latches and registers Transmission Gate, Gate delays, CMOS-Gate Transistor sizing, Power dissipation 3 4 Basic Physical Design of Simple Gates and Layout Issues: Layout issues for 6 inverter, Layout for NAND and NOR Gates, Complex Logic gates Layout, Layout optimization for performance. 2 5 Introduction to VHDL,Verilog & other design tools. VHDL Code for simple Logic 8 gates, flip-flops, shift-registers, Counters, Multiplexers, adders and subtractors. Text Books S. No. Name of authors’/books/publisher

Year of pub.

1

S. M. Sze: VLSI Technology, MGH.

2003

2

Debaprasad Das: VLSI Design, Oxford.

2011


Year of pub.

1

Angsuman Sarkaret. al.: VLSI Design and EDA Tools, Scitech Pub.

2011

2

S. M. Kang: CMOS Digital Integrated Circuits, MGH.

2003

3

Stephen A. Campbell: The Science & Engineering of Microelectronic Fabrication, Oxford. James D. Plummer, Micheal Deal & Petter B. Griffin: Silicon VLSI Tech. Fundamental Practice & Modeling, Prentice Hall.

2001

4

2000

5EX7A: POWER ELECTRONICS LAB (Common for EE and EX) 1

2 3 4 5 6 7 8 9 10 11 12

Study the comparison of following power electronics devices regarding ratings, performance characteristics and applications: Power Diode, Power Transistor, Thyristor, Diac, Triac, GTO, MOSFET, MCT and SIT. Determine V-I characteristics of SCR and measure forward breakdown voltage, latching and holding currents. Find V-I characteristicsof TRIAC and DIAC. Find output characteristics of MOSFET and IGBT. Find transfer characteristics of MOSFET and IGBT. Find UJT static emitter characteristics and study the variation in peak point and valley point. Study and test firing circuits for SCR-R, RC and UJT firing circuits. Study and test 3-phase diode bridge rectifier with R and RL loads. Study the effect of filters. Study and obtain waveforms ofsingle-phase half wave controlled rectifier with and without filters. Study the variation of output voltage with respect to firing angle. Study and obtain waveforms ofsingle-phase half controlled bridge rectifier with R and RL loads. Study and show the effect of freewheeling diode. Study and obtain waveforms ofsingle-phase full controlledbridge converter with R and RL loads. Study and show rectification and inversion operations with and without freewheeling diode. Control the speed of a dc motor using single-phase half controlled bridge rectifier and fully controlled bridge rectifier.Plot armature voltage versus speed characteristics. Reference/Suggested Books 1. P. Arora: Power Electronics Laboratory-Experiments and Organization, Narosa Pub. 2. P. B. Zbar: Industrial Electronics- A Text-Lab Manual, MGH. 5EX8A: COMMUNICATION LAB

1 2 3 4

5 6 7 8 9 10 11

Harmonic analysis of a square wave of modulated waveform Observe the amplitude modulated waveform and measures modulation index. Demodulation of the AM signal To modulate a high frequency carrier with sinusoidal signal to obtain FM signal. Demodulation of the FM signal To observe the following in a transmission line demonstrator kit : i. The propagation of pulse in non-reflecting Transmission line. ii. The effect of losses in Transmission line. iii. The resonance characteristics of al half wavelength long x-mission line. To study and observe the operation of a super heterodyne receiver To modulate a pulse carrier with sinusoidal signal to obtain PWM signal and demodulate it. To modulate a pulse carrier with sinusoidal signal to obtain PPM signal and demodulate it. To observe pulse amplitude modulated waveform and its demodulation. To observe the operation of a PCM encoder and decoder .To considers reason for using digital signal xmissions of analogsignals. Produce ASK signals, with and without carrier suppression, Examine the different processes required for demodulation inthe two cases. To observe the FSK wave forms and demodulate the FSK signals based on the properties of (a) Tuned circuits (b) On PI.L. 5EX9A: SYSTEM PROGRAMMING LAB (Common for EE and EX)

Basics of MATLAB matrices and vectors, matrix and array operations, Saving and loading data, plotting simple graphs, scripts and functions, Script files, Function files, Global Variables, Loops, Branches, Control flow, Advanced data objects, Multi-dimensional matrices, Structures, Applications in linear algebra curve fitting and interpolation. Numerical integration, Ordinary differential equation. (All contents is to be covered with tutorial sheets) Simulink: Idea about simulink, problems based on simulink. (All contents is to be covered with tutorial sheets)Write a program to generate Machine Op- code table using two pass Assembler. Reference/Suggested Books 1. Almos Gilat: MATLAB: An Introduction with Applications, Wiley India Ltd., 2004. 2. Ram N. Patel et. al.: Programming in MATLAB, Pearson.

5EX10A: DBMS LAB (Common for EE and EX) 1 2 3 4 5 6 7 8

Designing database and constraints using DDL statements. Experiments for practicing SQL query execution on designed database. Database connectivity using JDBC/ODBC. Features of embedded SQL. Designing front end in HLL and accessing data from backend database. Designing simple projects using front end-back end programming. Project for generating Electricity Bills Project for managing student’s attendance/marks details. 5EX11A: PROFESSIONAL ETHICS AND DISASTERS MANAGEMENT (Common for EE and EX)

Objectives:To help the students • To appreciate the importance and values and ethics in implementing the technology and ensure sustainable development, happiness and prosperity. • To understand the co-existence with nature and to be aware of potential natural and manmade disasters. Human Values: Effect of Technological Growth and Sustainable Development. 2 Profession and Human Values: Values crisis in contemporary society. Nature of values. Psychological Values, Societal Values and Aesthetic Values. Moral and Ethical values. 3 Professional Ethics: • Professional and Professionalism-Professional Accountability, Role of a professional, Ethic and image of profession. • Engineering Profession and Ethics-Technology and society, Ethical obligations of Engineering professionals, Roles of Engineers in industry, society, nation and the world. • Professional Responsibilities-Collegiality, Loyalty, Confidentially, Conflict of Interest, Whistle Blowing. 4 Disaster Management: Understanding Disasters and Hazards and related issues social and environmental. Risk and Vulnerability. Types of Disasters, their occurrence/ causes, impact and preventive measures: Natural Disasters- Hydro-meteorological Based Disasters like Flood, Flash Flood, Cloud Burst, Drought, Cyclone, Forest Fires; Geological Based Disasters like Earthquake, Tsunami, Landslides, Volcanic Eruptions. 5 Manmade Disasters: Chemical Industrial Hazards, Major Power Break Downs, Traffic Accidents, Fire Hazards, Nuclear Accidents.Disaster profile of Indian continent. Case studies. Disaster Management Cycle and its components. In order to fulfill objectives of course, (A) The institute shall be required to organize at least 3 expert lectures by eminent social workers/professional leaders. (B) Each student shall compulsorily be required to: I. Visit a social institution/NGO for at least 7 days during the semester and submit a Summary report. II. Perform a case study of a disaster that has occurred in last decade and submit a Summary report. Reference/Suggested Books 1. R Subramanian: Professional Ethics, oxford publishers. 2. Engineering Ethics: Concepts and cases by Charles E. Harris, Jr., Michael S. Pritchard, Michael J. Rabins. Cengage Learning, Delhi 3. Stephen H. Unger: Controlling Technology- Ethics and Responsible Engineers, John Willey and Sons. 4. Deborah Johnson: Ethical Issues in Engineering, Prentice Hall. 5. A. N. Tripathi: Human Values in the engineering Profession, Moniograph, Published by IIM Calcutta. 6. D. K. Sinha: Towards Basics of Natural Disaster Reduction, Researchco Book Center, Delhi. 7. Amita Sinvhal: Understanding Earthquake Disasters, MGH, New Delhi. 8. Selected Resources available on www.nidmindia.nic.in 1

Syllabus B.Tech. (Electrical & Electronics Engineering), 6thsemester 6EX1A: MODERN CONTROL THEORY (Common for EE and EX) B. Tech. (Electrical & Electronics) 6th Semester Max. Marks: 80 3L+1T Exam Hours: 3 UNIT CONTENTS CONTACT HOURS 1 Introduction: Concept of Linear vector space Linear Independence, Bases & 5 Representation, domain and range. Concept of Linearity, relaxedness, time invariance, causality. State Space Approach of Control System Analysis:Modern Vs conventional 3 control theory, concept of state, state variable state vector, state space, state space equations, Writing statespace equations of mechanical, Electrical systems, Analogous systems. 2 State Space Representation using physical and phase variables, comparison 5 form of system representation. Block diagram representation of state model. Signal flow graph representation. State space representation using canonical variables. Diagonal matrix. Jordan 3 canonical form, Derivation of transfer functions from state-model. 3 Solution of State Equations:Eigenvalues and Eigen vectors. Matrix.Exponential, 4 State transition matrix, Properties of state transition matrix. Computation of State transition matrix concepts of controllability & observability. 4 Pole placement by state feedback. 4 Digital Control Systems: Introduction, sampled data control systems, signal 4 reconstruction, difference equations. The z-transform, Z-Transfer Function. Block diagram analysis of sampled data 4 systems, z and s domain relationship. 5 Modeling of sample-hold circuit, steady state accuracy, stability in z-plane and Jury 4 stability criterion, bilinear transformation 4 Routh-Hurwitz criterion on s-planes, digital PID controllers, Introduction to adaptive control. Text Books S. No. Name of authors’/books/publisher 1 2

I. J. Nagrath and M. Gopal: Control Systems Engineering, 3rd Ed, New Age Publication. S. K. Bhattacharya: Control Systems Engineering, 3e, Pearson Publishers.



Year of pub.

1

Dhannesh N. Manik: Control System, Cengage Learning.

2010

2

Richard C. Dorf, Robert H. Bishop: Modern Control Systems, Prentice-Hall.

2008

3

M. Gopal: Digital Control and State Variable Methods, MGH.

2012

4

B. C. Kuo: Digital Control System, Oxford.

1980

5

C. H. Houpis and G. B. Lamont, Digital Control Systems, MGH.

1992

6

Donald E. Kiv: Optimal Control Theory- An Introduction, Prentice Hall.

2009

7

D. Roy, Choudhary: Modern Control Engineering, Prentice Hall of India.

2005

8

C. T. Chen: System Theory &Design, Oxford University Press.

1999

6EX2A: NEURAL NETWORKS B. Tech. (Electrical & Electronics) 6th Semester 3L UNIT CONTENTS 1

2

3

4

5

Max. Marks: 80 Exam Hours: 3 CONTACT HOURS Introduction: Introduction to Neural Networks, Biological basis for NN, Human 8 brain, Models of a Neuron, Directed Graphs, Feedback, Network architectures, Knowledge representation, Artificial intelligence & Neural Networks. Learning Processes:Introduction, Error-Correction learning, Memory -based 5 learning, Hebbian learning, Competitive learning, Boltzmann learning, Learning with a Teacher & without a teacher, learning tasks, Memory, Adaptation. 3 Single Layer Perceptrons: Introduction,Least-mean-square algorithm, Learning 8 Curves, Learning rate Annealing Techniques, Perceptron, Perceptron Convergence Theorem. Multilayer Perceptrons: Introduction, Back-Propagation Algorithm, XOR Problem, 8 Output representation and Decision rule, Feature Detection, Back-Propagation and Differentiation, Hessian Matrix, Generalization. Radial-basisfunction Networks &Self-organizingMaps: Introduction to Radial 5 basis function networks, Cover’s Theorem on the Separability of Patterns, Interpolation Problem, Generalized Radial-Basis function networks, XOR Problem. Self-Organizing map, Summary of SOM Algorithm, Properties of the feature map. 3


Year of pub.

1

Yagya Narayana: Artificial Neural Networks, Prentice Hall India 1999.

2009

2

James A. Freeman, David M. Skapura: Neural Networks-Algorithm, Applications and Programming Techniques. Pearson Publisher.

1991


Year of pub.

1

Satish Kumar: Neural Networks, TMH.

2004

2

James A. Anderson: An Introduction to Neural Networks.

1995

3

Dan. W. Patterson: Artificial Intelligence and Expert Systems.

1990

4

Bishop: Neural Networks for Pattern Recognition, Oxford

1993

6EX3A: SWITCHGEAR &PROTECTION (Common for EE and EX) B. Tech. (Electrical & Electronics) 6th Semester 3L+1T UNIT CONTENTS 1

2

3

4

5

Max. Marks: 80 Exam Hours: 3 CONTACT HOURS Static Relays:Introduction to static relays, merits and demerits. 6 Comparators:amplitude and phase comparators, duality between amplitude and phase comparators. Introduction to (a) amplitude comparators-circulating current type, phase splitting type and sampling type, (b) phase comparators-vector product type and coincidence type. Static over Current Relays:Introduction to instantaneous, definite time, inverse 2 time and directional overcurrent relays. Static Differential Relays:Brief description of static differential relay schemes5 single phase and three phase schemes. Introduction to static differential protection of generator and transformer. Static Distance Relays:Introduction to static impedance, reactance and mho relays. 3 Carrier Current Protection: Basic apparatus and scheme of power line carrier 4 system. Principle of operation of directional comparison and phase comparison carrier protection and carrier assisted distance protection. 4 Distance Protection:Effect of power swings on the performance of distance protection. Out of step tripping and blocking relays, mho relay with blinders. Introduction to quadrilateral and elliptical relays. Circuit Breakers-I:Electric arc and its characteristics, arc interruption-high 4 resistance interruption and current zero interruption. Arc interruption theories– recovery rate theory and energy balance theory. Restriking voltage and recovery voltage, develop expressions for restriking voltage 4 and RRRV. Resistance switching, current chopping and interruption of capacitive current. Oil circuit breakers-bulk oil and minimum oil circuit breakers. Air circuit breakers. Miniature Circuit breaker (MCB). Circuit Breakers-II: Air blast, SF6 and vacuum circuit breakers. Selection of circuit 4 breakers, rating of circuit breakers. Digital Protection: Introduction to digital protection. Brief description of block 4 diagram of digital relay. Introduction to digital overcurrent, transformer differential and transmission line distance protection.


Bhavesh Bhalja, R. P. Maheshari and Nilesh G. Chothani: Protection and Switchgear, Oxford. Bhuvanesh A. Oza and Nair: Power System Protection and Switchgear, MGH.



Year of pub.

1

B. Ravindranath and M. Chander: Power system Protection and Switchgear, Wiley.

1977

2

B. Ram and D. N. Vishwakarma: Power System Protection and Switchgear, MGH.

2001

3

Y. G. Paithankar and S. R. Bhide: Fundamentals of Power System Protection, PHI. T.S.M. Rao: Power System Protection- Static Relays with Microprocessor Applications, MGH. A. R. Van C. Warringtaon: Protective Relays-Their Theory and Practice, Vol. I & II, Jhon Willey & Sons.

2010

4 5 6

S. S. Rao: Switchgear and Protection, Khanna Publishers.

1989 1978 2008

6EX4A: ADVANCED POWER ELECTRONICS (Common for EE and EX) B.Tech. (Electrical) 6th semester 3L+1T UNIT 1

2

3

4

5

Max. Marks: 80 Exam Hours: 3 CONTENTS CONTACT HOURS AC Voltage Controllers: Principle of On-Off Control, Principle of Phase control, 5 Single Phase Bi-directional Controllers with Resistive Loads, Single Phase Controllers with Inductive Loads, Three Phase full wave AC controllers, AC Voltage Controller with PWM Control. Cyclo-converters: Basic principle of operation, single phase to single phase, 8 three-phase to three-phase and three-phase to single phase cyclo-converters. Output equation, Control circuit. Inverters: Principle of Operation, Single-phase bridge inverters. Three phase bridge 6 Inverters: 180 and 120 degree of conduction. VSI and CSI. Voltage control of Single Phase and Three Phase Inverters, Harmonic analysis, 5 harmonic reduction techniques, Pulse width modulation techniques. Resonant Pulse Inverter: Series resonant inverter with unidirectional switches, 8 parallel resonant inverter, class E resonant inverter, L –type and M-type ZCS resonant converter, ZVS resonant converter. 4 Power Supplies: Switched Mode DC Power Supplies, fly-back converter, forward converter, half and full bridge converter, resonant DC power supplies, bi-directional power supplies. Resonant AC power supplies, bidirectional AC power supplies. Multistage 4 conversions, Control Circuits: Voltage Mode Control, Current Mode Control


M. H. Rashid: Power Electronics: Circuits, Devices & Applications, Pearson Publishers. Bimal Bose: Power Electronics & Motor Drives, Elsevier-2006.

Reference Books S. No. Name of authors’/books/publisher 1 2 3 4


Year of pub.

V. R. Moorthy: Power Electronics: Devices, Circuits and Industrial Applications, Oxford. P. C. Sen: Power Electronics, MGH.

2005

Ned Mohan, T. M. Undeland and W. P. Robbins: Power Electronics- Converters, Applications and Design, Wiley India Ltd, 2008. R. Krishnan: electric motor drives- modeling, analysis and control, Pearson Edu.

2007

1987

2001

6EX5A: MICROPROCESSOR AND MICROCONTROLLER B. Tech. (Electrical & Electronics) 6th Semester 3L UNIT CONTENTS 1 2

3 4 5

Max. Marks: 80 Exam Hours: 3 CONTACT HOURS Introduction:CPU, address bus, data bus and control bus. Input/ Output devices, 8 buffers, encoders, latches and memories. 8085 Microprocessor Architecture:Internal data operations and registers, pins and 8 signals, peripheral devices and memory organization, interrupts. CISC and RISC architecture overview. 8085 Microprocessor Instructions:Classification, format and timing. Instruction set. 8 Programming and debugging, 8 bit and 16 bit instructions. 8085 Microprocessor Interfacing:8259, 8257, 8255, 8253, 8155 chips and their 8 applications. A/D conversion, memory, keyboard and display interface (8279). Introduction To 8051 Microcontroller:General features & architecture of 8051. 8 Memory, timers and interrupts. Pin details. Interfacing and applications.


Gaonkar, Ramesh S.: Microprocessor Architecture, programming and applications with the 8085, Penram International Publishing 5th Ed. Douglas Hall: Microprocessors and Interfacing, Revised Second Edition (SIE) MGH.



Year of pub.

1

Mathur A. P.: Introduction to Microprocessors, MGH.

1989

2

Ray, A. K. & Burchandi, K. M.: Advanced Microprocessors and Peripherals, MGH.

2006

3

Krishna Kant: Microprocessors and Microcontrollers, PHI Learning.

2007

4

Brey, Barry B.: INTEL Microprocessors, Prentice Hall (India).

2011

5

M. Rafiquzzaman: Microprocessors- Theory and applications, PHI

1992

6

B. Ram: Advanced Microprocessor & Interfacing, MGH.

2001

7

Liu and Gibson G. A.: Microcomputer Systems- The 8086/8088 Family, PHI.

1986

6EX6.1A: SMART GRID TECHNOLOGY B. Tech. (Electrical & Electronics) 6th Semester 3L+1T UNIT CONTENTS 1

2

3

4

5

Max. Marks: 80 Exam Hours: 3 CONTACT HOURS Introduction to Smart Grid: Evolution of Electric Grid, Concept, Definitions and 5 Need for Smart Grid, Smart grid drivers, functions, opportunities, challenges and benefits Difference between conventional & Smart Grid, Concept of Resilient &Self-Healing 3 Grid, Present development & International policies in Smart Grid, Diverse perspectives from experts and global Smart Grid initiatives. Smart Grid Technologies: Technology Drivers, Smart energy resources, Smart 5 substations, Substation Automation, Feeder Automation ,Transmission systems: EMS, FACTS and HVDC, Wide area monitoring, Protection and Control, Distribution Systems:DMS, Volt/Var control, Fault 3 Detection, Isolation and service restoration, Outage management, High-Efficiency Distribution Transformers, Phase Shifting Transformers, Plug in Hybrid Electric Vehicles (PHEV). Smart Meters and Advanced Metering Infrastructure: Introduction to Smart 4 Meters, Advanced Metering infrastructure (AMI) drivers and benefits, AMI protocols, standards and initiatives, AMI needs in the smart grid, Phasor Measurement, Unit (PMU), Intelligent 4 Electronic Devices (IED) & their application for monitoring & protection. Power Quality Management in Smart Grid: Power Quality & EMC in Smart Grid, 5 Power Quality issues of Grid connected Renewable Energy Sources, Power Quality Conditioners for Smart Grid, Web based Power Quality monitoring, 3 Power Quality Audit. High Performance Computing for Smart Grid Applications: Local Area Network 4 (LAN), House Area Network (HAN), Wide Area Network (WAN), Broadband over Power line (BPL), IP based Protocols, Basics of Web Service and CLOUD Computing to make Smart 4 Grids smarter, Cyber Security for Smart Grid


2

Vehbi C. Güngör, Dilan Sahin, Taskin Kocak, Salih Ergüt, Concettina Buccella, Carlo Cecati, and Gerhard P. Hancke: Smart Grid Technologies-Communication Technologies and Standards IEEE Transactions on Industrial Informatics, Vol. 7, No. 4, November 2011. Xi Fang, Satyajayant Misra, Guoliang Xue, and Dejun Yang: Smart Grid-The New and Improved Power Grid- A Survey, IEEE Transaction on Smart Grids.


Stuart Borlase: Smart Grid- Infrastructure, Technology and Solutions, CRC Press.

Year of pub. 2011

2011

Year of pub. 2012

6EX6.2A: POWER SYSTEM INSTRUMENTATION (Common for EE and EX) B. Tech. (Electrical & Electronics) 6th Semester Max. Marks: 80 3L+1T Exam Hours: 3 UNIT CONTENTS CONTACT HOURS 1 Theory of Errors: Accuracy and precision, systematic and random errors, limits of 8 error, probableerror and standarddeviation. Gaussian error curves, combination of errors. 2 Transducers:Construction & Operating Characteristics of active and digital 4 transducers, Measurement of temperature, pressure, displacement, acceleration, noise level. Instrumentation for strain, displacement, velocity, acceleration, force, torque and 4 temperature. 3 SignalConditioning: Instrumentation amplifiers, isolation amplifiers, analog 4 multipliers, analog dividers, function generators, timers, sample and hold, optical and magnetic isolators. Frequency to voltage converters, temperature to current converters. Shielding and 4 grounding. 8 4 Power System Instrumentation-I:Measurement of voltage, current, phase angle, frequency, active power and reactive power in power plants. Energy meters and multipart tariff meters. Basic idea of LT & HT panel’s. 5 Power System Instrumentation-II:Capacitive voltage transformers and their 8 transient behavior, Current Transformers for measurement and protection,composite errors and transient response. Text Books S. No. Name of authors’/books/publisher 1 2

R. H. Cerni and L. E. Foster: Instrumentation for Engineering Measurements, John Wiley and Sons. Curtis and D. Hohnson: Process Control Instrumentation Technology, John Wiley and sons.



Year of pub.

1

R. Morrison: Instrumentation Fundamentals and Applications, John Wiley and Sons.

1984

2

A. K. Sawhney: Advanced Measurements & Instrumentation, Dhanpat Rai & Sons.

1994

3

E.O. Decblin: Measurement System– Application & design, MGH.

1975

4

W.D. Cooper and A.P. Beltried: Electronics Instrumentation and Measurement Techniques, Prentice Hall International. A. S. Moris: Principles of Measurement & Instrumentation, Prentice Hall, 1993.

1987

5

1993

6EX6.3A: DIGITAL COMMUNICATION AND INFORMATION THEORY (Common for EE and EX) B. Tech. (Electrical & Electronics) 6th Semester 3L+1T UNIT CONTENTS 1

2 3 4

5

Max. Marks: 80 Exam Hours: 3 CONTACT HOURS PCM & DELTA Modulation Systems:PCM and delta modulation, quantization 4 noise in PCM and delta modulation. Signal-to-noise ratio in PCM and delta modulation, T1 Carrier System, Comparison of PCM and DM. Adaptive delta Modulation. Bit, 4 word and frame synchronization, Matched filter detection. Digital Modulation Techniques: Various techniques of phase shift, amplitude shift 8 and frequency shift keying. Minimum shift keying. Modulation & Demodulation. Error Probability in Digital Modulation: Calculation of error probabilities for 8 PSK, ASK, FSK & MSK techniques. Information Theory:Amount of Information, Average Information, Entropy, 4 Information rate, Increase in Average information per bit by coding, Shannon's Theorem and Shannon's bound Capacity of a Gaussian Channel, BW-S/N trade off, Orthogonal signal transmission. 4 Coding: Coding of Information, Hamming code, Single Parity-Bit Code, Linear 8 Block code, cyclic code &convolution code.


Year of pub.

1

R. N. Mutagi: Digital Communication, 2nd ed., Oxford.

2013

2

P. Ramakrishna Rao: Communication Systems, MGH.

2013


Year of pub.

1

H. Taub & D.L. Schilling: Principles of Communication Systems, MGH.

2008

2

Simon Haykin: Communication Systems, John Wiley & Sons.

2008

3

Proakis: Digital Communication, MGH.

2008

4

Sklar: Digital Communication, Pearson Education.

2009

5

P. Chakrabarti: Principles of Digital Communications, Danpatrai & Sons.

1999

6

K. Sam Shanmugam: Digital and Analog Communication System, John Wiley Sons.

2006

7

Lathi, B. P.: Modern Digital &Analog Communication System, Oxford Press.

2009

8

A.B. Carlson: Digital Communication Systems, MGH.

1988

6EX7A: CONTROL SYSTEM LAB (Common for EE and EX) 1 2 3

4 5 6

7

8 9 10 11

Introduction to MATLAB Computing Control Software. Defining Systems in TF, ZPK form. (a) Plot step response of a given TF and system in state-space. Take different values of damping ratio and wn natural undamped frequency. (b) Plot ramp response. For a given 2ndorder system plot step response and obtain time response specification. To design 1st order R-C circuits and observe its response with the following inputs and trace the curve. (a) Step (b) Ramp (c) Impulse To design 2nd order electrical network and study its transient response for step input and following cases. (a) Under damped system (b) Over damped System. (c) Critically damped system. To Study the frequency response of following compensating Networks, plot the graph and final out corner frequencies. (a) Log Network (b) Lead Network (c) Log-lead Network. To draw characteristics of ac servomotor To perform experiment on Potentiometer error detector. Check for the stability of a given closed loop system. Plot bode plot for a 2ndorder system and find GM and PM. 6EX8A: POWER SYSTEM LAB (Common for EE and EX)

1 2 3

4 5

Study the burden effect on the performance of CT and measure ratio error. Find out the sequence components of currents in three 1-Phase transformers and 3- Phase Transformerand compare their results. (i) Study over current relay. (ii) Draw the current-time characteristic of an over current relay for TMS=1 & 0.5 and PSM=1.25 &1.0. (i) Study percentage bias differential relay. (ii) Plot the characteristics of a percentage bias differential relay for 20%, 30% and 40% biasing. Study gas actuated Buchholz relay. 6EX9A: ADVANCED POWER ELECTRONICS LAB (Common for EE and EX)

1 2 3 4 5 6 7 8 9 10 11 12

Study and test AC voltage regulators using triac, antiparallel thyristors and triac & diac. Study and test single phase PWM inverter. Study and test buck, boost and buck- boost regulators. Study and test MOSFET chopper. Study and test Zero voltage switching. Study and test SCR DC circuit breaker. Control speed of a dc motor using a chopper and plot armature voltage versus speed characteristic. Control speed of a single-phase induction motor using single phase AC voltage regulator. (i) Study single-phase dual converter. (ii) Study speed control of dc motor using single phase dual converter. Study one, two and four quadrant choppers (DC-DC converters). Study speed control of dc motor using one, two and four quadrant choppers. Study single-phase cycloconverter.

6EX10A: MICROPROCESOR & MICROCONTROLLER LAB 1 2 3 4 5 6 7 8 9 10 11 12

Study the hardware, functions, memory structure and operation of 8085 microprocessor kit. Program to perform integer division: (i) 8-bit by 8-bit (ii) 16-bit by 8-bit. Transfer of a block of data in memory to another place in memory in the direct and reverse order. Searching a number in an array and finding its parity. Sorting of array in: (i) Ascending (ii) Descending order Programme to perform following conversion: (i) BCD to ASCII (ii) BCD to Hexadecimal Programme to multiply two 8-bit numbers. Programme to generate and sum 15 fibanocci numbers. Programme for rolling display of message “INDIAN”. To insert a number at correct place in a sorted array. Serial and Parallel data transfer on output port 8155 & 8255 & designing of disco light, running light, and sequential lights on off by above hardware. Generation of different waveform on 8253/ 8254 programmable timer. 6EE11A: ENTREPRENEURSHIP DEVELOPMENT (Common for EE and EX)

1 2 3 4 5 6

Definition of entrepreneur, qualities of a successful entrepreneur, Charms of being an entrepreneur, achievement- motivation, leadership and entrepreneurial competencies. Decision-making, procedures and formalities for starting own business, financial supportsystem. Identification and selection of business opportunities and market survey, business plan, Implementation and customer satisfaction. Business crises, kproblem-solving attitude, communication skill, Government policies for entrepreneurs. Knowledge based enterprises, Scope of entrepreneur in present context, area of future entrepreneurship. Marketing & Sales Promotion, Techno-Economic Feasibility Assessment by Preparation of Preliminary & Detailed project report.

Syllabus B.Tech. (Electrical & Electronics Engineering), 7thsemester 7EX1A: POWER SYSTEM PLANNING (Common for EE and EX) B. Tech. (Electrical & Electronics) 7th Semester Max. Marks: 80 3L Exam Hours: 3 UNIT CONTENTS CONTACT HOURS 1 Introduction of power planning, National and Regional Planning, structure of 4 P.S., planning tools Electricity Regulation, Electrical Forecasting, forecasting techniques modeling. 4 2 Generation planning, Integrated power generation cogeneration/captive power, 4 Power pooling and power trading. Transmission and distribution planning. Power system Economics. Power sector finance, financial planning, private 4 participation Rural Electrification investment, concept of Rational tariffs. 3 Power supply Reliability, Reliability planning. System operation planning, load 4 management, load prediction, reactive power balance Online power flow studies, state estimation, computerized management, power system 4 simulator. 4 Computer aided planning, wheeling. Environmental effects, the greenhouse effect 4 Technological impacts. Insulation coordination. Reactive compensation. 4 5 Optimal power system expansion planning : Formulation of least cost 3 optimization problem incorporating the capital, Operating and maintenance cost of candidate plants of different types (Thermal, Hydro, Nuclear, Non-conventional etc.) and minimum assured reliability constraint – 5 optimization techniques for solution by programming. Text Books S. No. Name of authors’/books/publisher 1 2

X. Wang, J. R. Mc Donald: Modern Power System Planning, MGH. A. S. Pabla: Electrical Power System Planning, Machmillan India Ltd.


M. Tllic, F. Faliana and L. Fink: Power System Restructuring Engineering and Economics, Kulwar Academic Publisher. L. L. Lie: Power System Restructuring and Deregulation, John Willey & Sons UK 2001.



7EX2A: POWER SYSTEM ANALYSIS (Common for EE and EX) B. Tech. (Electrical & Electronics) 7th Semester Max. Marks: 80 3L+1T Exam Hours: 3 UNIT CONTENTS CONTACT HOURS 1 Percent and per unit quantities. Single line diagram for a balanced 3-phase system 4 Admittance Model: Branch and node admittances Equivalent admittance network 4 and calculation of Y bus. Modification of an existing Y bus. 2 Impendence Model: Bus admittance and impedance matrices. Thevenin’s theorem 3 and Z bus. Direct determination of Z bus. Modification of an existing bus. Symmetrical fault Analysis: Transient on a Transmission line, short circuit of a 5 synchronous machine on no load, short circuit of a loaded synchronous machine. Equivalent circuits of synchronous machine under sub transient, transient and steady state conditions. Selection of circuit breakers, Algorithm for short circuit studies. Analysis of three-phase faults. 3 Symmetrical Components: Fortescue theorem, symmetrical component 4 transformation. Phase shift in star-delta transformers. Sequence Impedances of transmission lines, Synchronous Machine and Transformers, zero sequence network of transformers and transmission lines. Construction of sequence networks of power system. Fault Analysis: Analysis of single line to ground faults using symmetrical 4 components, connection of sequence networks under the fault condition. 4 Unsymmetrical Fault Analysis: (i) Analysis of line-to-line and double line to ground faults using symmetrical components, connection of sequence networks 5 under fault conditions. Analysis of unsymmetrical shunt faults using bus impedance matrix method. 3 5 Load Flow Analysis: Load flow problem, development of load flow equations, 4 bus classification Gauss Seidel, Newton Raphosn, decoupled and fast decoupled methods for load flow 4 analysis. Comparison of load flow methods. Text Books S. No. Name of authors’/books/publisher

Year of pub.

1

J. J. Grainger, William, D. Stevenson Jr.: Power System Analysis, MGH.

2003

2

T. K. Nagsarkar & M. S. Sukhija: Power System Analysis, Oxford University Press, 2007.

2007


Year of pub.

2

J. D. Glover, M. S. Sharma & T. J. Overbye: Power System Analysis and Design, Cengage Learning. Nasser Tleis: Power System Modelling and Fault Analysis, Elsevier.

2007 2007

3

Kothari & Nagrath: Modern Power System Analysis, MGH.

2011

4

Haadi Saadat: Power System Analysis.

2002

7EX3A: ARTIFICIAL INTELLIGENCE TECHNIQUES (Common for EE and EX) B. Tech. (Electrical & Electronics) 7th Semester 3L UNIT CONTENTS 1 2

3

4 5

Max. Marks: 80 Exam Hours: 3 CONTACT HOURS Artificial Intelligence: Introduction to AI and knowledge based Expert systems, 4 Introduction, Importance and Definition of AI, ES, ES building tools and shells. 4 Knowledge Representation: Concept of knowledge, Representation of knowledge 4 using logics rules, frames. Procedural versus. Declarative knowledge, forward versus backward chaining Control Strategies: Concept of heuristic search, search techniques depth first 4 search, Breath first search, Generate & test hill climbing, best first search. Artificial Neural Network: Biological Neurons and synapses, characteristics 4 Artificial Neural Networks, types of activation functions. Perceptions: Perception representation, limitations of perceptrons. Single layer and 4 multiplayer perceptrons. Perceptron learning algorithms. Basic Concepts in Learning ANN: Supervised learning, Back propagation algorithm, 8 unsupervised learning, Kohonen’s top field network & Algorithm. Fuzzy Logic: Fuzzy logic concepts, Fuzzy relation and membership functions, 4 Defuzzification, Fuzzy controllers, Genetic Algorithm: concepts, coding, reproduction, crossover, mutation, scaling and 4 fitness.


Year of pub.

1

Saroj Kaushik: Artificial Intelligence. Cengage Learning.

2007

2

Elaine Rich and Kevin Knight: Artificial Intelligence 3/e, MGH

2004


Year of pub.

1

Padhy: Artificial Intelligence & Intelligent Systems, Oxford

2005

2

James Anderson: An introduction to Neural Networks.

1995

3

Dan. W Patterson: Artificial Intelligence and Expert Systems.

1990

4

Kumar Satish: Neural Networks, 2nd ed., MGH.

2004

5

S. Rajsekaran & G. A. Vijayalakshmi Pai: Neural Networks, Fuzzy Logic and Genetic Algorithm- Synthesis and Applications, Prentice Hall of India. Siman Haykin: Neural Netowrks, Prentice Hall of India.

2003

6

2004

7EX4A: NON CONVENTIONAL ENERGY SOURCES (Common for EE and EX) B. Tech. (Electrical & Electronics) 7th Semester 3L

Max. Marks: 80 Exam Hours: 3

UNIT

CONTENTS

1

Introduction: World energy situation, conventional and non-conventional energy sources, Indian energy scene. Tidal Energy: Introduction to tidal power. Components of tidal power plants, double basin arrangement. Power generation. Advantages and limitations of tidal power generation. Prospects of tidal energy in India. Solar Energy: Solar radiation, solar radiation geometry, solar radiation on tilted surface. Solar energy collector. Flat- plate collector, concentrating collector parabolidal and heliostat. Solar pond. Basic solar power plant. Solar cell, solar cell array, basic photo-voltaic power generating system. Wind Energy: Basic principle of wind energy conversion, efficiency of conversion, site selection. Electric power generation-basic components, horizontal axis and vertical axis wind turbines, towers, generators, control and monitoring components. Basic electric generation schemes- constant speed constant frequency, variable speed constant frequency and variable speed variable frequency schemes. Applications of wind energy. Geothermal Energy: Geothermal fields, estimates of geothermal power. Basic geothermal steam power plant, binary fluid geothermal power plant and geothermal preheat hybrid power plant. Advantages and disadvantages of geothermal energy. Applications of geothermal energy. Geothermal energy in India. Nuclear Fusion Energy: Introduction, nuclear fission and nuclear fusion. Requirements for nuclear fusion. Plasma confinement – magnetic confinement and inertial confinement. Basic Tokamak reactor, laser fusion reactor. Advantages of nuclear fusion. Fusion hybridand cold fusion. Biomass Energy: Introduction, biomass categories, bio-fuels. Introduction to biomass conversion technologies. Biogas generation, basic biogas plants-fixed dome type, floating gasholder type, Deen Bandhu biogas plant, Pragati design biogas plant. Utilization of bio gas. Energy plantation. Pyrolysis scheme. Alternative liquid fuels ethanol and methanol. Ethanol production.

2

3

4

5


CONTACT HOURS 4 4

4

4 4

4 4

4 3 5

Year of pub.

1

G. D. Rao: Renewable Energy

2010

2

B. H. Khan: Non-Conventional Energy Resources, MGH.

2006


A. N. Mathur: Non-Conventional Resources of Energy. rd

Boyle: Renewable Energy, 3 ed Oxford. th


3

Bent Sorensen, 4 ed.: Renewable Energy, Elsevier.

2009

4

V. V. N. Kishore: Renewable Energy Engineering and Technology, TERI.

2006

5

Garg & Prakash: Solar Energy : Fundamentals and Applications, MGH

2000

6

David Boyles: Bio Energy, Elis Horwood Ltd.,

1984

7

N.K. Bansal, M. Kleemann, M. Heliss: Renewable energy sources and conversion technology, MGH, 1990.

1990

7EX5A: POWER SYSTEM ENGINEERING (Common for EE and EX) B. Tech. (Electrical & Electronics) 7th Semester Max. Marks: 80 3L+1T Exam Hours: 3 UNIT

CONTENTS

1

Economic Operation of Power Systems: Introduction, system constraints, optimal operation of power systems. Input output, heat rate and incremental rate curves of thermal generating units. Economic distribution of load between generating units within a plant. Economic distribution of load between power stations, transmission loss equation. Introduction to unit commitment and dynamic programming. Power System Stability-I: Power angle equations and power angle curves under steady state and transient conditions. Rotor dynamics and swing equation (solution of swing equation not included). Synchronizing power coefficient. Introduction to steady state and dynamic stabilities, steady state stability limit. Power System Stability-II: Introduction to transient stability. Equal area criterion and its application to transient stability studies under basic disturbances. Critical clearing angle and critical clearing time. Factors affecting stability and methods to improve stability. Excitation Systems: Introduction of excitation systems of synchronous machines, types of excitation systems, Elements of various excitation systems and their control (functional block diagrams and their brief description)-DC excitation systems, AC excitation systems, brushless excitation system. Interconnected Power Systems: Introduction to isolated and interconnected powers systems. Reserve capacity of power stations, spinning and maintenance resaves. Advantages and problems of interconnected power systems. Power systems inter connection in India. Tap Changing transformer, phase angle control and phase shifting transformer. Series compensation of transmission lines, location and protection of series capacitors, advantages and problems Introduction to power system security. Introduction to voltage stability.

2

3

4

5


CONTACT HOURS 3

5

5

3 4 4 4

4

5

3 Year of pub.

1

J. Nagrath and D.P. Kothari: Power System Engineering 2/e, MGH.

2011

2

J. J. Grainger and W. D. Stevenson: Power System Analysis, MGH.

2003


Year of pub.

1

B. R. Gupta: Power System Analysis and Design, Third Edition, S. Chand & Co.

2008

2

C. L. Wadhwa: Electrical Power Systems, New age international Ltd. Third Edition

2009

3

W. D. Stevenson: Element of Power System Analysis, MGH.

1955

4

B. R. Gupta: Generation of Electrical Energy, S. Chand Publication.

2009

7EX6.1A: DIGITAL SIGNAL PROCESSING B. Tech. (Electrical & Electronics) 7th Semester 3L+1T UNIT CONTENTS 1

2

3

4

5

Max. Marks: 80 Exam Hours: 3 CONTACT HOURS Sampling: Discrete time processing of Continuous-time signals, continuous-time 8 processing of discrete-time signals, changing the sampling rate using discrete-time processing. Transform Analysis of LTI Systems: Introduction, The frequency response of LTI 8 systems, System functions for systems characterized by LCCD (Linear Constant Coefficient Difference) equations, All-pass system, MinimumPhase systems, Linear systems with linear phase. Structures for Discrete-Time Systems: Block diagram and signal flow graph 8 representation of LCCD (LCCD-LinearConstant Coefficient Difference) equations, Basic structures for IIR and FIR systems, Transposed forms. Filter Design Techniques: Introduction, Analog filter Design: Butterworth & 8 Chebyshev.IIR filter design by impulse invariance & Bilinear transformation. Design of FIR filters by Windowing: Rectangular, Hanning, Hamming & Kaiser The Discrete Fourier Transform (DFT): Properties of the DFT, Linear 8 Convolution using DFT. Efficient computation of the DFT: Decimation-in-Time and Decimation-in frequency FFT Algorithms. Processing of speech signals: Vocoders, linear predictive coders.


Year of pub.

Prokis & Manolakis: Digital Signal Processing- Principles, Algorithms & Application, PHI. Salivahanan: Digital Signal Processing 2/e, TMH.


2007 2011

Year of pub. nd

Li Tan and J. Jiang: Digital Signal Processing, 2 ed., Elsevier. th

2013

2

P. Ramesh Babu: Digital Signal Processing, 4 ed., Scitech Pub.

2003

3

Chen Chi-Tsong: Digital Signal Processing, Oxford.

2001

4

Rabiner & Gold: Theory & Applications of Digital Signal Processing, PHI.

2009

5

Bhag Guru: Electromagnetic Field Theory Fundamentals, Cambridge Uni. Press.

2004

7EX6.2A: COMPUTER AIDED DESIGN OF ELECTRICAL MACHINES (Common for EE and EX) B. Tech. (Electrical & Electronics) 7th Semester Max. Marks: 80 3L+1T Exam Hours: 3 UNIT CONTENTS CONTACT HOURS 1 Basic Principles of Electrical Machine Design: Specifications, Factors affecting 4 the design, Limitations, main dimension, loadings, output equation, factor affecting the size and rating, Electrical Engineering Materials: conducting, magnetic and insulating materials. 4 Magnetic Circuit Calculation: Ohm’s law for magnetic circuit, mmf required for air gap and iron parts, tapered teeth, real and apparent flux density, magnetizing current. 2 Heating and Cooling of Electrical Machines: heat dissipation and heat flow 4 equations, Newton’s law of cooling, equations for temperature rise, Rating of Machines: Continuous, short and intermittent ratings, mean 4 temperature rise, hydrogen cooling of turbo alternators, quantity of cooling medium. 3 Computer Aided Design of Transformers: Power and Distribution 8 Transformers, core and yoke cross sections, square and stepped core, output equations, main dimensions, types & design of windings, optimization concepts. 4 Computer Aided Design of Synchronous Machines: Turbo and Hydro alternators, 8 choice of specific magnetic & electric loading, short circuit ratio and its effects air gap length, output equation, main dimensions, flow charts for design of synchronous machine, design of stator core & winding. 5 Computer Aided Design of Induction Machines: Output equation, main 8 dimensions, design criteria, flow charts for design of induction motor, air gap length, design of stator core and winding, rotor design. Text Books S. No. Name of authors’/books/publisher

Year of pub.

1

K. Sawhney: A Course in Electrical Machine Design, Dhanpat Rai & Sons.

1984

2

B. Edikins: Generalized Theory of Electrical Machines.

1995


Year of pub.

1

Fitzegerald Kingsley: Electrical Machinery.

2002

2

M. G. Say: The Performance and Design of AC Machines, Pitman & Sons.

1958

3

R. K. Agrawal: Electrical Machine Design

2009

7EX6.3A: OPERATING SYSTEM B. Tech. (Electrical & Electronics) 7 Semester 3L+1T UNIT CONTENTS th

1 2 3

4

5

Max. Marks: 80 Exam Hours: 3 CONTACT HOURS responsibilities, 8

Introduction: History, Operating system services, types, generations, LINUX, WINDOWS Process Management: Operations on process, Process state, Scheduling, Criteria, scheduling algorithms, Evaluation, Synchronization, Semaphores, Monitors. Memory Management: Swapping, Continuous memory allocation, Paging, Pure paging, Demand paging, Page-replacement algorithms, thrashing, ExamplePentium, Disk Scheduling. Information Management: File and directory concept, Access methods, Protection, Free space management, Efficiency and performance, Access matrix, Capabilitybased systems, Program threats, User authentication, Firewall. Dead Locks: System model, Dead lock characterization, Deadlock prevention, Avoidance, Detection, Recovery, Classic problems of synchronization


A. S. Tanenbaum: Modern Operating Systems, Pearson Education, Asia. D. M. Dhamdhere: Operating Systems- A Concept Based Approach 2/e, MGH.


Achyut Godble: Operating Systems, MGH.

8 8

8

8


Year of pub. 2011

7EX7A: POWER SYSTEM PLANNNG LAB (Common for EE and EX) 1. 2. 3. 4. 5. 6. 7. 8.

Status of National and Regional Planning, for power system Write components of Structure of power system Explain in detail various planning tools. Write short note on Electricity Regulation Modeling of Electrical Forecasting techniques Transmission and distribution planning concept of Rational tariffs Rural Electrification 7EX8A: POWER SYSTEM MODELLING AND SIMULATION LAB (Common for EE and EX)

1. 2. 3. 4. 5. 6. 7.

Simulate Swing Equation in Simulink (MATLAB) Modeling of Synchronous Machine. Modeling of Induction Machine. Simulate simple circuits using Circuit Maker. (a) Modeling of Synchronous Machine with PSS (b) Simulation of Synchronous Machine with FACTS device. (a) Modeling of Synchronous Machine with FACTS device (b) Simulation of Synchronous Machine with FACTS devices. FACTS Controller designs with FACT devices for SMIB system. 7EX9A: INDUSTRIAL ECONOMICS &MANAGEMENT (Common for EE and EX)

1

2

3

4

5

Money Banking and Trade: Functions of money, supply & demand for money, money price level & inflation, black money, meaning, magnitude & consequences. Functions of Commercial banks, banking system in India, shortcomings and improvements. Function of RBI, monetary policymaking, objectives and features. Sources of public revenue, principles of taxation, direct and indirect taxes, Theory of international trade, balance of trade and payment, Foreign exchange control, devaluation New economic policy: Liberalization, extending privatization, globalization. Management Principles: Management functions, responsibilities of management to society, development of management thought. Nature of planning, decision making, management by objectives, Line and staff authority relationships, decentralization and delegation of authority, span of management. Production Management: Production planning and control, inventory control, quality control and Total quality management. ISO standards Related to quality/Environment/safety etc. Tools of Project Management: CPM, PERT, project information systems. Marketing functions, management of sales and advertising marketing research. Human Resource Management: Function, application of industrial psychology for selection, training and recruitment. Communication process, media channels and barriers to effective communication, theories of motivation, leadership. Finance and Account Management: Engineering Economics: Investment decision, present worth, annual worth and rate of return methods. Payback time. Need for good cost accounting system, cost control techniques of financial control, financial statements, financial ratios, breakeven analysis, budgeting and budgetary control.

Syllabus B.Tech. (Electrical & Electronics Engineering), 8thsemester 8EX1A: EHV AC/DC TRANSMISSION (Common for EE and EX) B. Tech. (Electrical & Electronics) 8th Semester Max. Marks: 80 3L+1T Exam Hours: 3 UNIT CONTENTS CONTACT HOURS 1 EHV AC Transmission: Need of EHV transmission lines, power handling capacity 4 and surge impedance loading. Problems of EHV transmission, Bundled Conductors: geometric mean radius of bundle, properties of bundle 4 conductors. Electrostatic fields of EHV lines and their effects, corona effects: Corona loss, audio and radio noise. 2 Load Frequency Control: Introduction to control of active and reactive power flow, 4 turbine speed governing system. Speed governing characteristic of generating unit and load sharing between parallel operating generators Method of Load Frequency Control: Flat frequency, flat tie line and tie line 4 load bias control. Automatic generation control (description of block diagram only). 3 Voltage Control: No load receiving end voltage and reactive power generation. 4 Methods of voltage control. Synchronous phase modifier Shunt capacitors and reactors, saturable reactors, Thyristorised static VAR 4 compensators- TCR, FC-TCR and TSC- TCR. 4 FACTS: Introduction to FACTS controllers, types of FACTS controllers, Brief 8 description of STATCOM, Thyristor controlled series capacitors and unified power flow controller. 5 HVDC Transmission: Types of D.C. links, advantages and disadvantages of HVDC 4 transmission. Basic scheme and equipment of converter station. Ground return. Basic principles of DC link control and basic converter control characteristics. 4 Application of HVDC transmission. Text Books S. No. Name of authors’/books/publisher

Year of pub.

1

K. R. Padiyar: HVDC Power Transmission Systems. NEW AGE PUB

1990

2

K. R. Padiyar: HVDC Power Transmission System, Wiley Eastern Ltd., 1990

1990


Year of pub.

1

E. W. Kimbark: Direct Current Transmission, Vol. 1, Wiley Interscience, 1971.

1971

2

J. Arrillaga: H.V.D.C Transmission, Peter Peregrines, 1983.

1983

3

J. Arrillaga HVDC et. al, : Computer Modelling of Electrical Power System. John Wiley 1993.

1993

8EX2A: ELECTRIC DRIVES AND THEIR CONTROL (Common for EE and EX) B. Tech. (Electrical & Electronics) 8th Semester Max. Marks: 80 3L+1T Exam Hours: 3 UNIT CONTENTS CONTACT HOURS 1 Dynamics of Electric Drives: Fundamental torque equations, speed-torque 4 conventions and multi-quadrant operation, Nature and classification of load torques, steady state stability, load equalization, 4 close loop configurations of drives. 2 DC Drives: Speed torque curves, torque and power limitation in armature 4 voltage and field control, Starting, Braking: Regenerative Braking, dynamic braking and plugging. Speed 4 Control-Controlled Rectifier fed DC drives, Chopper Controlled DC drives. 3 Induction Motor Drives-I: Starting, Braking-Regenerative braking, plugging and 4 dynamic braking. Speed Control: Stator voltage control, variable frequency control from voltage 4 source, Voltage Source Inverter (VSI) Control. 4 Induction Motor Drives-II: Variable frequency control from current source, Current 4 Source Inverter (CSI) Control, Cycloconverter Control, Static rotor resistance control, Slip Power Recovery- Stator 4 Scherbius drive, Static Kramer drive. 5 Synchronous Motor Drive: Control of Synchronous Motor-Separately Controlled 4 and VSI fed Self-Controlled Synchronous Motor Drives. Dynamic and Regenerative Braking of Synchronous Motor with VSI. Control of 4 Synchronous Motor Using Current Source Inverter (CSI). Text Books S. No. Name of authors’/books/publisher 1 2

G. K. Dubey: Fundamentals of Electrical Drives, Narosa Publishing House, New Delhi. B. K. Bose: Power Electronics and Motor Drives, Elsevier.



Year of pub.

1

V. Subrahmanyam: Electric Drives- Concepts and Applications, MGH.

2011

2

Theodore Wildi: Electrical Machines, Drives and Power Systems, Pearson

2007

3

S. K. Pillai: A First Course on Electrical Drives, Wiley Eastern limited, India.

1989

4

N. K. De and Prashant K. Sen: Electric Drives, Prentice Hall of India Ltd.

1999

8EX3A: PROTECTION OF POWER SYSTEM (Common for EE and EX) B. Tech. (Electrical & Electronics) 8th Semester Max. Marks: 80 3L Exam Hours: 3 UNIT CONTENTS CONTACT HOURS 1 Causes and Consequences of Dangerous Currents: Faults, overloads and switching 4 over currents. Introduction to protection, trip circuit of a circuit breaker. Functional characteristics of a relay, zone of protection, primary and backup protection. CTs &PTs: Current transformer construction, measurement and protective CTs. 4 Type of potential transformers. Steady state ratio and phase angle errors in CTs and PTs. Transient errors in CT and CVT (Capacitive Voltage Transformer). 2 Overcurrent Protection: HRC fuse and thermal relay. Overcurrent relays – 4 instantaneous, definite time, inverse time and inverse definite minimum time overcurrent relays, time and current gradings. Induction disc type relay. Directional overcurrent relay, 300, 600 and 900connections. 4 Earth fault relay. Brief description of overcurrent protective schemes for a feeder, parallel feeders and ring mains. 3 Generator Protection: Stator protection–differential and percentage differential 4 protection, protection against stator inter-turn faults, stator overheating protection. Rotor protection-protection against excitation and prime mover failure, field 4 earth fault and unbalanced stator currents (negative sequence current protection). 4 Transformer Protection: Percentage differential protection, magnetizing inrush 4 current, percentage differential relay with harmonic restraint. Buchholz relay. Differential protection of generator transfer unit. Busbar Protection: Differential protection of busbars. Highimpedance relay scheme, 4 frame leakage protection 5 Transmission Line Protection: Introduction to distance protection. Construction, 4 operating principle and characteristics of an electromagnetic impedance relay. Effect of arc resistance.Induction cup type reactance and mho relays. Comparison between impedance, reactance and mho relays. Three stepped distance protection of transmission line. Induction Motor Protection: Introduction to various faults and abnormal operating 4 conditions, unbalance supply voltage and single phasing. Introduction to protection of induction motors- HRC fuse and overcurrent, percentage differential, earth fault and negative sequence voltage relays Text Books S. No. Name of authors’/books/publisher

Year of pub.

1

Badri Ram: Power System Protection and Switchgear, MGH

2011

2

Ravindra Nath M. Chander: Power System Protection and Switch Gear, John Wiley Eastern

1977


Year of pub.

1

Sunil S. Rao.: Power System Protection and Switch Gear, Khanna Publishers 1989

1999

2

Oza: Power System Protection and Switchgear, MGH

2010

3

T. S. Madhava Rao: Power System Protections (Static Relays), MGH, 1989.

1989

4

A. R. Van C Warrington: Protective Relays, Chapman and Hall London, 1968.

1968

5

S. K. Basu and S. Chaudhary: Power System Protection, Raju Primlan Oxford, 1983.

1983

8EX4.1A: UTILIZATION OF ELECTRICAL POWER (Common for EE and EX) B. Tech. (Electrical & Electronics) 8th Semester Max. Marks: 80 3L+1T Exam Hours: 3 UNIT CONTENTS CONTACT HOURS 1 Electric Heating: Different methods of electric heating. Principle of high frequency 4 induction and dielectric heating. Construction, operation, performance and applications of arc furnace and induction furnace Electric Welding: Welding process, welding transformer, Classification of Electric 4 Welding: arc welding, resistance welding, welding of various metals. 2 Illuminations: Definitions, laws of illuminations, polar curves, luminous efficiency, 4 photometer, incandescent lamps, filament materials, Halogen lamp, electric discharge lamps, sodium vapour lamp, mercury vapour lamp 4 and fluorescent lamp. Light Calculations: commercial, industrial, street and flood lighting. 3 Electrolytic Process: Principles and applications of electrolysis, electro-deposition, 4 Manufactures of chemicals, anodizing, electro-polishing , electro-cleaning, electroextraction, electro-refining, electro-stripping (parting) power supplies for electrolytic process. 4 Electric Traction & Means of Supplying Power: Systems of Electric 4 Traction: DC & AC Systems, Power Supply for Electric Traction System: Comparison and application of different systems. Sub-station equipment and layout, conductor rail & pantograph. 5 Traction Methods: Types of services, speed time and speed distance curves, 4 estimation of power and energy requirements, Mechanics of train movement. Co-efficient of adhesion, Adhesive weight, effective weight. Traction Motor 4 Controls: DC and AC traction motors, Series parallel starting. Methods of electric braking of traction motors. Text Books S. No. Name of authors’/books/publisher

Year of pub.

1

C. L. Wadhwa: Utilization of Electric Traction Electric Power.

1989

2

H. Partab: Art and Science of Electrical Energy, Dhanpat Rai & Sons

1975


H. Partab:Modern Electric Traction, Dhanpat Rai & Sons

Year of pub. 1973

8EX4.2A: IMAGE PROCESSING AND PATTERN RECGNITION B. Tech. (Electrical & Electronics) 8th Semester Max. Marks: 80 3L+1T Exam Hours: 3 UNIT CONTENTS CONTACT HOURS 1 Introduction: Imaging in ultraviolet and visible band. Fundamental steps in image 8 processing. Components inimage processing. Image perception in eye, light and electromagnetic spectrum, Image sensing and acquisition using sensor array. 2 Digital Image Fundamentals: Image sampling and quantization, Representing 8 digital images, Spatial and gray-level resolution, Aliasing and Moiré patterns, zooming and Shrinking digital images. 3 Image Restoration: Image restoration model, Noise Models, Spatial and frequency 4 properties of noise, noise probability density functions. Noise - only spatial filter, Mean filter Statistic filter and adaptive filter, Frequency 4 domain filters - Band reject filter, Band pass filter and Notch filter. 4 Image Compression: Compression Fundamentals - Coding Redundancy, Interpixel 4 redundancy, Psycho visual redundancy and Fidelity criteria. Image Compression models, Source encoder and decoder. Channel encoder and decoder, Lossy compression and compression standards. Color 4 space formats, scaling methodologies (like horizontal, vertical up/down scaling). Display format (VGA, NTSC, PAL). 5 Expert System and Pattern Recognition: Use of computers in problem solving, 4 information representation, searching, theorem proving, and pattern matching with substitution. Methods for knowledge representation, searching, spatial, temporal and common 4 sense reasoning, and logic and probabilistic inferencing. Applications in expertsystems and robotics. Text Books S. No. Name of authors’/books/publisher

Year of pub.

1

Rafael C. Gonzalez: Digital Image Processing, Pearson Education, Asia.

2009

2

Vipula Singh: Digital Image Processing, Elesvier.

2013


Year of pub.

1

Kenneth R. Castleman: Digital Image Processing, Pearson Education, Asia.

2007

2

Nick Effard: Digital Image Processing, Pearson Education, Asia.

2000

3

Jain A. K.: Digital Image Processing, Prentice Hall of India.

1989

4

Shinghal: Pattern Recognition- Techniques and Applications, Oxford.

2006

5

Jayaraman: Digital Image Processing, TMH.

2011

8EX4.3A: VHDL B. Tech. (Electrical & Electronics) 8 Semester 3L+1T UNIT CONTENTS th

1 2 3 4

5

Max. Marks: 80 Exam Hours: 3 CONTACT HOURS Introduction: Fundamental & history of various hardware description language, 8 Design flow of ASICs and standard logic circuits using software. Combinational Circuit Building Blocks: Multiplexer, Decoders, encoders, Code 8 Converters, VHDL Code for Combinational Circuits. Sequential Circuits: VHDL code for Flip-Flops, shift registers, counters. 8 Synchronous/Asynchronous Sequential Circuits: Mealy & Moore type FSMs, 8 VHDL Code for Mealy & Moore Machines, VHDL Codes for Serial Adder, Vending Machine. Digital System Design: Building Block circuits, Memory organization, SRAM, 8 Design examples of divider, Multiplier, Shifting & Sorting Operations, Clock Synchronization, CPU organization and design concepts.


Stephen Brown and Zvonki Vranesic: Fundamentals of Digital Logic circuit VHDL Design 2/e, MGH. Z. Navabi: Analysis and Modeling of Digital Systems, MGH.



Year of pub.

1

D. L. Perry: VHDL, 3rd ed., MGH.

1991

2

Morris Mano: Digital Logic & Computer Design, Prentice Hall of India.

1979

8EX5A: COMPUTER BASED POWER SYSTEM LAB (Common for EE and EX) 1. 2. 3. 4. 5. 6.

Fault analysis (for 3 to 6 bus) and verify the results using MATLAB or any available software for the cases: (i) LG Fault (ii) LLG Fault (iii) LL Fault and (iv) 3-Phase Fault Load flow analysis for a given system (for 3 to 6 bus) using (i) Gauss Seidal (ii) Newton Raphson (iii) Fast Decoupled Method and verify results using MATLAB or any available software Study of voltage security analysis Study of overload security analysis and obtain results for the given problem using MATLAB or any software. Study of economic load dispatch problem with different methods. Study of transient stability analysis using MATLAB/ETAP Software. 8EX6A: ELECTRICAL DRIVES AND CONTROL LAB (Common for EE and EX)

1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15.

Study and test the firing circuit of three phase half controlled bridge converter. Study and obtain waveforms of 3 phase half controlled bridge converter with R and RL loads. Study and test the firing circuit of 3-phase full controlled bridge converter. Study and obtain waveforms of 3-phase full controlled bridge converter with R and RL loads. Study and test 3-phase AC voltage regulator. Control speed of dc motor using 3-phase half controlled bridge converter. Plot armature voltage versus speed characteristic. Control speed of dc motor using 3-phase full controlled bridge converter. Plot armature voltage versus speed characteristic. Control speed of a 3-phase induction motor in variable stator voltage mode using 3-phase AC voltage regulator. Control speed of a 3-phase BLDC motor. Control speed of a 3-phase PMSM motor using frequency and voltage control Control speed of universal motor using AC voltage regulator. Study 3-phase dual converter. Study speed control of dc motor using 3-phase dual converter. Study three-phase cycloconverter and speed control of synchronous motor using cycloconverter. Control of 3-Phase Induction Motor in variable frequency V/f constant mode using 3-phase inverter

Syllabus B.Tech. (Electrical & Electronics Engineering), 3rd semester

Recommend Documents