installation instructions - Honda Powersports

USE AND CARE INFORMATION. Check the accessory mounts frequently and. • retighten if necessary. Before starting your motorcycle, check that the. • side...

7 downloads 749 Views 178KB Size
Accessory

INSTALLATION INSTRUCTIONS

Application

Publication No.

Mll 13973

CENTERSTAND

NC700X/XD

P/N 08M70-MGS-A30

Issue Date

January 2012

Honda Dealer: Please give a copy of these instructions to your customer. PARTS LIST

TORQUE CHART Tighten all screws, bolts, and nuts to their specified torque values. Refer to the Service Manual for the torque values of the removed parts.

(2) (6)

(4) (3)

Item (7)

kgf·m

Ibf·ft

6 mm socket bolt

12

1.2

9

Spring hook

22

2.2

16

USE AND CARE INFORMATION

(1)

(5)

No.

N·m

Description

Qty

(1)

Centerstand

1

(2)

Centerstand shaft

1

(3)

Spring (large)

1

(4)

Spring (small)

1

(5)

Spring hook

1

(6)

6 mm socket bolt

1

(7)

Rubber stop

1

TOOLS AND SUPPLIES REQUIRED Open-end wrench (12 mm) Hex wrench (5 mm) Spring tool Grease Dish soap solution (Water : dish soap / 100 : 1) Shop towel Torque wrench

© 2012 Honda Motor Co., Ltd. - All Rights Reserved.

• Check the accessor y mounts frequently and retighten if necessary. • Before starting your motorcycle, check that the sidestand and the centerstand are fully retracted. • Always set the parking brake when parking the NC700XD (DCT model) on the centerstand. • Always choose a firm, level surface when setting the centerstand.

INSTALLATION CAUTION: • To prevent burns, allow the engine, exhaust system, radiator, etc. to cool before installing the accessory. NOTE: • Be extremely careful when installing the springs as the combined tension of the springs is very strong. • Keep the motorcycle on its sidestand when installing the centerstand. • The spring installation shall be performed by two people. While one person holds the motorcycle, another person installs the spring.

87943-MGS-A500

1 of 4

1.

Remove the muffler bolts, washers, and nut as shown. NUT

3.

Apply dish soap solution to the rubber stop in the area shown.

WASHER BOLT

RUBBER STOP

WASHER

2.

DISH SOAP SOLUTION Apply.

BOLT

4.

Install the spring hook as shown.

Install the rubber stop in the position shown. RUBBER STOP

CENTERSTAND

RUBBER ST”OP

SPRING HOOK

CENTERSTAND

2 of 4

87943-MGS-A500

© 2012 Honda Motor Co., Ltd. - All Rights Reserved.

5.

Apply grease to the position shown.

8.

GREASE Apply.

Install the spring assembly as shown. • First install the spring assembly to the spring hook, then to the centerstand. • The spring installation should be performed by two people. While one person holds the motorcycle, another person installs the spring. • To ease installation, first hook the small spring. SPRING HOOK

CENTERSTAND SHAFT

6.

Install the centerstand as shown.

CENTERSTAND

SPRING ASSEMBLY

SPRING HOOK SIDE

6 mm SOCKET BOLT

CENTERSTAND SHAFT

CENTERSTAND SIDE CENTERSTAND

7.

Slide the small spring into the large spring as shown.

SPRING (small)

SPRING (large)

© 2012 Honda Motor Co., Ltd. - All Rights Reserved.

87943-MGS-A500

3 of 4

• If the spring assembly is too hard to install, remove the centerstand shaft. First hook the spring assembly, then install the centerstand shaft. 6 mm SOCKET BOLT

SPRING ASSEMBLY CENTERSTAND SHAFT Insert while aligning the holes of the frame and centerstand.

9.

CENTERSTAND

Install the muffler bolt, washer, and nut in the reverse order of removal.

4 of 4

87943-MGS-A500

© 2012 Honda Motor Co., Ltd. - All Rights Reserved.